2005-2008 Yaris · Service Manual HEATER & AIR CONDITIONING SYSTEM

PTC Heater Circuit

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

PTC heater relays are closed in accordance with signals from the air conditioning amplifier and power is supplied to the PTC heater assembly installed on the radiator heater unit.

WIRING DIAGRAM

E120474E01

INSPECTION PROCEDURE


1. INSPECT FUSE (HTR SUB1, HTR SUB2)
  1. Remove the HTR SUB1 and HTR SUB2 fuses from the engine room relay block.

  1. Measure the resistance.

    Standard resistance:
    Tester Item
    Specified Condition
    HTR SUB1 fuse
    Below 1 Ω
    HTR SUB2 fuse
    Below 1 Ω

  1. Reinstall the HTR SUB1 and HTR SUB2 fuses.



NG
REPLACE FUSE
OK


2. INSPECT AIR CONDITIONING AMPLIFIER
E115805E03
  1. Remove the air conditioning amplifier with its connectors still connected.

  1. Turn the ignition switch on (IG).

  1. When the PTC heater operating conditions are met (engine at idling speed or faster, ambient temperature is 10°C (50°F) or less, engine coolant temperature is 65°C (149°F) or less, set temperature switch is set to MAX HOT), turn the blower switch to the Lo setting.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Specified Condition
    E11-3 (PTC1) - Body ground
    10 to 14 V
    E11-22 (PTC2) - Body ground
    10 to 14 V
    E11-4 (PTC3) - Body ground
    10 to 14 V

  1. Reinstall the air conditioning amplifier.



NG
REPLACE AIR CONDITIONING AMPLIFIER
OK


3. INSPECT PTC HEATER RELAY (HTR SUB1, HTR SUB2, HTR SUB3)
E115946E01
  1. Remove the HTR SUB1 relay from the engine room relay block.

  1. Remove the HTR SUB2 and HTR SUB3 relays from the engine room sub relay block.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω (when battery voltage is applied to terminals 1 and 2)

  1. Reinstall the HTR SUB1 relay.

  1. Reinstall the HTR SUB2 and HTR SUB3 relays.



NG
REPLACE PTC HEATER RELAY
OK


4. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - PTC HEATER RELAY)
E120467E03
  1. Remove the HTR SUB1 relay.

  1. Remove the HTR SUB2 and HTR SUB3 relays.

  1. Turn the ignition switch on (IG).

  1. When the PTC heater operating conditions are met (engine at idling speed or faster, ambient temperature is 10°C (50°F) or less, engine coolant temperature is 65°C (149°F) or less, set temperature switch is set to MAX HOT), turn the blower switch to the Lo setting.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Specified Condition
    HTR SUB1-2 - Body ground
    10 to 14 V
    HTR SUB2-2 - Body ground
    10 to 14 V
    HTR SUB3-2 - Body ground
    10 to 14 V

  1. Reinstall the HTR SUB1 relay.

  1. Reinstall the HTR SUB2 and HTR SUB3 relays.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - BODY GROUND)
E120467E03
  1. Remove the HTR SUB1 relay.

  1. Remove the HTR SUB2 and HTR SUB3 relays from the engine room sub relay block.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified condition
    HTR SUB1-1 - Body ground
    Below 1 Ω
    HTR SUB2-1 - Body ground
    Below 1 Ω
    HTR SUB3-1 - Body ground
    Below 1 Ω

  1. Reinstall the HTR SUB1 relay.

  1. Reinstall the HTR SUB2 and HTR SUB3 relays.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT PTC HEATER ASSEMBLY
E115947E03
  1. Disconnect the A17 PTC heater assembly connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified condition
    1 - 2
    Below 1 Ω
    2 - 3
    Below 1 Ω
    1 - 3
    Below 1 Ω

  1. Reconnect the PTC heater assembly connector.



NG
REPLACE PTC HEATER ASSEMBLY
OK


7. CHECK HARNESS AND CONNECTOR (BATTERY - PTC HEATER RELAY)
E120467E03
  1. Remove the HTR SUB1 relay.

  1. Remove the HTR SUB2 and HTR SUB3 relays.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Specified condition
    HTR SUB1-5 - Body ground
    10 to 14 V
    HTR SUB2-5 - Body ground
    10 to 14 V
    HTR SUB3-5 - body ground
    10 to 14 V

  1. Reinstall the HTR SUB1 relay.

  1. Reinstall the HTR SUB2 and HTR SUB3 relays.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - PTC HEATER ASSEMBLY)
E120290E03
  1. Remove the HTR SUB1 relay.

  1. Remove the HTR SUB2 and HTR SUB3 relays.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    HTR SUB1-3 - A17-2 (B)
    Below 1 Ω
    HTR SUB2-3 - A17-3 (B)
    Below 1 Ω
    HTR SUB3-3 - A17-1 (B)
    Below 1 Ω

  1. Reinstall the HTR SUB1 relay.

  1. Reinstall the HTR SUB2 and HTR SUB3 relays.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER


← Blower Motor Circuit (from Aug 2005)IG Power Source Circuit (from Aug 2005) →