2005-2008 Yaris · Service Manual ENGINE

P2101 Throttle Actuator Control Motor Circuit Range/Performance

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

The throttle actuator is operated by the ECM, and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the Throttle Position (TP) sensor, which is mounted on the throttle body. The TP sensor provides feedback to the ECM in order that it can control the throttle actuator, and therefore the throttle valve, appropriately in response to driver inputs.

HINT:
This ETCS (Electronic Throttle Control System) does not use a throttle cable.

DTC No.
DTC Detection Condition
Trouble Area
P2101
The driving IC detects a malfunction inside itself during operation (1 trip detection logic)
  1. ECM
P2102
The driving IC detects a short in the throttle control motor circuit during operation (1 trip detection logic)
  1. Short in throttle control motor circuit
  2. Throttle body assembly
P2103
The driving IC detects a open in the throttle control motor circuit during operation (1 trip detection logic)
  1. Open in throttle control motor circuit
  2. Throttle body assembly
P2111
Either of following conditions is met: (1 trip detection logic)
  1. When the absolute values for difference between the target throttle angle and actual throttle angle is more than threshold for 0.5 seconds or more
  2. The motor drive duty ratio for opening or closing the throttle valve is 80 % or more for 5 seconds or more
  1. Open or short in throttle control motor circuit
  2. Throttle body assembly
P2118
The driving IC detects a high-current malfunction causing overheat in the throttle control motor circuit during operation (1 trip detection logic)
  1. Throttle body assembly

HINT:
The monitor always runs while the ignition switch is on (IG) or the engine is running.


WIRING DIAGRAM

A116140E01

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK OUTPUT DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the output DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P2102 and P2111
    A
    P2103 and P2111
    A
    P2111 and P2118
    A
    P2111
    B
    P2101 and P2111
    C



B
Go to step 3

C
REPLACE ECM
A


2. CHECK HARNESS AND CONNECTOR (ECM - THROTTLE BODY)
A113691E03
  1. Disconnect the throttle body assembly connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    M+ (A32-2) - M+ (C39-4)
    Below 1 Ω
    M- (A32-3) - M- (C39-1)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    M+ (A32-2) - Body ground
    10 kΩ or higher
    M- (A32-3) - Body ground
    10 kΩ or higher

  1. Reconnect the throttle body assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK THROTTLE BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
  1. Remove the throttle body assembly.

  1. Check for contamination between the throttle valve and the housing, and check that the throttle valve moves smoothly.

    OK:
    No contamination between the throttle valve and the housing, and the throttle valve moves smoothly.

  1. Reinstall the throttle body assembly.

  1. Perform electronic throttle learning (Click here).



NG
CLEAN THROTTLE BODY ASSEMBLY
OK


4. REPLACE THROTTLE BODY ASSEMBLY
  1. Replace the throttle body assembly.

  1. Perform electronic throttle learning (Click here).


NEXT


5. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Throttle Pos.

  1. Read the value when the accelerator pedal is operated.

    OK:
    The throttle position sensor value varies with changes in the angle of the accelerator pedal.



NG
CHECK HARNESS AND CONNECTOR (THROTTLE BODY - ECM)
OK

CHECK WHETHER DTC OUTPUT RECURS


← P1127 Condition for ETCS initialization (from Aug 2005)P2109 Throttle / Pedal Position Sensor "A" Minimum Stop Performance (from Aug 2005) →