2005-2008 Yaris · Service Manual BRAKE

CALIBRATION

Troubleshooting · Vehicles built from Aug 2005


DESCRIPTION
  1. After replacing components relating to the VSC or performing "Front wheel alignment adjustment", clear and read the sensor calibration data.
  2. Follow the chart to perform calibration.
    Replacing Parts / Operation
    Necessary Operation
    Skid Control ECU
    Yaw rate and deceleration sensor zero point calibration.
    Yaw Rate Sensor
    1. Zero point calibration data clearance.
    2. Yaw rate and deceleration sensor zero point calibration.
    Front Wheel Alignment Adjustment
    1. Zero point calibration data clearance.
    2. Yaw rate and deceleration sensor zero point calibration.

CLEAR ZERO POINT CALIBRATION DATA (USING INTELLIGENT TESTER)

  1. A107926E08
    Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG).

  3. C107606
    Operate the intelligent tester to erase the codes (select "Reset Memory").

    HINT:
    Refer to the intelligent tester operator's manual for further details.

  4. Using the intelligent tester, perform the zero point calibration of the yaw rate and deceleration sensor.


PREFORM ZERO POINT CALIBRATION OF YAW RATE AND DECELERATION SENSOR (USING INTELLIGENT TESTER)

NOTICE:
  1. While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it and keep it stationary. (Do not start the engine.)
  2. Perform this on a level surface (with an inclination of less than 1 degree).

  1. Procedures for Test Mode.

    1. A/T: Check that the shift lever is in the P position and apply the parking brake.
      M/T: Check that the shift lever is in neutral and apply the parking brake.

      NOTICE:
      DTC C1210/36 and C1336/39 will be recorded if the shift lever is not in neutral (M/T) or the P position (A/T) (Click here).

    2. A107926E08
      Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch on (IG).

    4. Set the intelligent tester to test mode (select "Test Mode").

      HINT:
      Refer to the intelligent tester operator's manual for further details.

  2. Obtain the zero point of the yaw rate and deceleration sensor.

    1. Keep the vehicle stationary on a level surface for 2 seconds or more.

    2. BR03904E22
      Check that the VSC warning light blinks as shown in the illustration.

      HINT:
      1. If the VSC warning light does not blink, perform the zero point calibration again.
      2. The zero point calibration is performed only once after the system enters test mode.
      3. Calibration cannot be performed again until the stored data is cleared once.

    3. Turn the ignition switch off.


CLEAR ZERO POINT CALIBRATION DATA (USING SST CHECK WIRE)
  1. Turn the ignition switch on (IG).

  2. F100115E01
    Using SST, connect and disconnect terminals TS and CG of the DLC3 4 times or more within 8 seconds.
    SST
    09843-18040  

  3. Check that the VSC warning light comes on.

  4. Remove the SST from the terminals of the DLC3.

  5. Using a check wire, perform the zero point calibration of the yaw rate and deceleration sensor.


PERFORM ZERO POINT CALIBRATION OF YAW RATE AND DECELERATION SENSOR (USING SST CHECK WIRE)

NOTICE:
  1. While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it and keep it stationary. (Do not start the engine.)
  2. Perform this on a level surface (with an inclination of less than 1 degree).

  1. Procedures for Test Mode.

    1. Turn the ignition switch off.

    2. F100115E01
      Using SST, connect terminals TS and CG of the DLC3.
      SST
      09843-18040  

    3. A/T: Check that the shift lever is in the P position and apply the parking brake.
      M/T: Check that the shift lever is in neutral and apply the parking brake.

      NOTICE:
      DTC C1210/36 and C1336/39 will be recorded if the shift lever is not in neutral (M/T) or the P position (A/T) (Click here).

  2. Obtain the zero point of the yaw rate and deceleration sensor.

    1. Turn the ignition switch on (IG).

    2. Keep the vehicle stationary on a level surface for 2 seconds or more.

    3. BR03904E22
      Check that the VSC warning light blinks as shown in the illustration.

      HINT:
      1. If the VSC warning light does not blink, perform the zero point calibration again.
      2. The zero point calibration is performed only once after the system enters test mode.
      3. Calibration cannot be performed again until the stored data is cleared once.

    4. Turn the ignition switch off.

← CHECK FOR INTERMITTENT PROBLEMS (from Aug 2005)TEST MODE PROCEDURE (from Aug 2005) →