2005-2008 Yaris · Service Manual BRAKE

C1231/31 Steering Angle Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

The steering sensor signal is sent to the skid control ECU via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the steering sensor zero point malfunction diagnostic function.
DTC No.
DTC Detecting Conditions
Trouble Areas
C1231/31
When IG1 terminal voltage 9.5 V or more, steering angle sensor malfunction signal received.
  1. Steering sensor
  2. Steering sensor circuit
  3. Steering sensor power supply
  4. CAN communication system

WIRING DIAGRAM

C121696E01
C118707E01

INSPECTION PROCEDURE

HINT:
  1. When U0073/94, U0123/62, U0124/95 or U0126/63 is output together with C1231/31, inspect and repair the trouble areas indicated by U0073/94, U0123/62, U0124/95 or U0126/63 first.
  2. When there are problems with the speed sensor or the yaw rate sensor, DTCs for the steering sensor may be output even when the steering sensor is normal. When DTCs for the speed sensor or yaw rate sensor are output together with other DTCs for the steering sensor, inspect and repair the speed sensor and yaw rate sensor first, and then inspect and repair the steering sensor.
  3. Start the inspection from step 1 when using the intelligent tester and from step 2 when not using the intelligent tester.


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruptions in the wire harness and connectors between the skid control ECU and the steering sensor (Click here).

    DATA LIST: ABS/VSC/TRC 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    Steering Open
    Steering angle sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal

    OK:
    There are no momentary interruptions.

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 4
OK


2. CHECK DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG) again and check that no CAN communication system DTC is output.

  1. Drive the vehicle and turn the steering wheel to the right and left at a speed of 35 km/h (24 mph) and check that no speed and yaw rate sensor DTCs are output.

    Result
    Proceed to
    DTC not output
    A
    CAN communication system DTC output
    B
    Speed sensor or yaw rate sensor DTC output
    C



B
CAN COMMUNICATION SYSTEM

C
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
A


3. INSPECT STEERING SENSOR
  1. Remove the steering wheel and the column cover lower.

  1. C122523E01
    Disconnect the steering sensor connector.

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Conditions
    D62-1(IG) - Body ground
    Ignition switch on (IG)
    10 to 14 V
    D62-3 (BAT) - Body ground
    Always
    10 to 14 V

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Conditions
    D62-2 (ESS) - Body ground
    Ignition switch off
    Below 1Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEERING SENSOR

4. CHECK AND REPLACE HARNESS AND CONNECTOR

NEXT


5. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle and turn the steering wheel to the right and left at a speed of 45km/h (28 mph) or more for several seconds.

  1. Check if the same DTC is recorded (Click here).

    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
Go to step 2
A

END


← C1223/43 ABS Control System Malfunction (from Aug 2005)C1232/32 Stuck in Deceleration Sensor (+ 7 more codes) (from Aug 2005) →