2005-2008 Yaris · Service Manual BRAKE

C1232/32 Stuck in Deceleration Sensor

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

The skid control ECU receives signals from the yaw rate and deceleration sensor via the CAN communication system.
The yaw rate sensor has a built-in deceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).
If there is trouble in the bus lines between the yaw rate and deceleration sensor and the CAN communication system, DTC U0123/62 (malfunction in CAN communication with the yaw rate sensor) and U0124/95 (malfunction in CAN communication with the deceleration sensor) are output.
These DTCs are also output when the calibration has not been completed.
DTCs C0371/71 and C1279/79 are deleted when the yaw rate and deceleration sensor sends a yaw rate and/or deceleration signal or test mode ends. DTCs C0371/71 and C1279/79 are output only in test mode.
DTC No.
DTC Detecting Conditions
Trouble Areas
C1232/32
At vehicle speed of 10 km/h (6 mph) or more, either GL1 or GL2 (input signal) does not change for 30 seconds or more.
  1. Yaw rate sensor
  2. Yaw rate sensor circuit
C0371/71
Detected only during test mode
  1. Yaw rate sensor
  2. Yaw rate sensor circuit
C1234/34
Sensor malfunction signal received from yaw rate sensor.
  1. Yaw rate sensor
  2. Yaw rate sensor circuit
C1243/43
While vehicle speed changes from 30 km/h (19 mph) to 0 km/h (0 mph), condition that values of GL1 and GL2 do not change occurs 16 times or more.
  1. Yaw rate sensor
  2. Yaw rate sensor circuit
C1244/44
When either of following conditions (1 or 2) detected:
  1. Data malfunction signal received from deceleration sensor.
  2. After difference between GL1 and GL2 becomes 0.6 G or more with vehicle stationary, difference remains 0.4 G or more for 60 seconds or more.
  1. Yaw rate sensor
  2. Yaw rate sensor circuit
C1245/45
At vehicle speed of 30 km/h (19 mph) or more, difference between forward and backward G calculated from deceleration sensor value and that calculated from vehicle speed sensor value exceeds 0.35 G for 60 seconds or more.
  1. Yaw rate sensor
  2. Yaw rate sensor circuit
C1279/79
Detected only during test mode.
  1. Yaw rate sensor
  2. Yaw rate sensor circuit
C1381/97
At vehicle speed of more than 3 km/h (2 mph), deceleration sensor power source malfunction signal received for 10 seconds or more.
  1. Yaw rate sensor
  2. Yaw rate sensor circuit

WIRING DIAGRAM

Click here.

INSPECTION PROCEDURE

HINT:
When U0123/62, U0124/95 or U0126/63 is output together with C1232/32, C1234/34, C1243/43, C1244/44, C1245/45, or C1387/97, inspect and repair the trouble areas indicated by U0123/62, U0124/95 or U0126/63 first.


1. CHECK DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG) again and check that no CAN communication system DTC(s) is output.

  1. Drive the vehicle at a speed of 30 km/h (19 mph) or more and check that no DTCs are output.

    Result
    Proceed to
    DTC output (relating to yaw rate and deceleration sensor)
    A
    DTC output (relating to CAN communication system)
    B
    DTC not output
    C



B
CAN COMMUNICATION SYSTEM

C
END
A


2. CHECK YAW RATE SENSOR INSTALLATION
  1. Check that the yaw rate sensor has been installed correctly (Click here).

    OK:
    The sensor is tightened to the specified torque.
    The sensor is not tilted.



NG
INSTALL YAW RATE SENSOR CORRECTLY
OK


3. INSPECT YAW RATE SENSOR
  1. Disconnect the yaw rate sensor connector.

  1. Turn the ignition switch on (IG).

  1. C121701E01
    Measure the voltage.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D63-5 (IG) - Body ground
    Ignition switch on (IG)
    11 to 14 V

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    D63-1 (GND) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. REPLACE YAW RATE SENSOR

NEXT

PERFORM YAW RATE AND DECELERATION SENSOR ZERO POINT CALIBRATION


← C1231/31 Steering Angle Sensor Circuit Malfunction (from Aug 2005)C1241/41 Low Battery Positive Voltage or Abnormally High Battery Positive Voltage (from Aug 2005) →