2005-2008 Yaris · Service Manual BODY ELECTRICAL

Speaker Circuit

Circuit diagnosis · Vehicles built from Jan 2006

Versions by build date: Aug 2005 – Dec 2005 from Jan 2006

DESCRIPTION

Sound signals that have been amplified by the stereo component amplifier are sent to the speakers from the radio receiver through this circuit. If there is a short in this circuit, the sound cannot be heard from the speakers even though there is no malfunction in the speakers.

WIRING DIAGRAM

I101508E06
E118196E04
E122654E02
E118196E05

INSPECTION PROCEDURE


1. CHECK SPEAKER
  1. Check whether sounds is emitted from the speakers.

    Result
    Proceed to
    Front No. 1 speakers have problems (Front and rear 4-speaker system and SEDAN)
    A
    Front No. 1 speakers have problems (6-speaker system and Front 4-speaker system)
    B
    Front No. 2 speakers have problems (6-speaker system and Front 4-speaker system)
    C
    Rear No. 1 speakers (6-speaker system Front and rear 4-speaker system and SEDAN)
    D



B
Go to step 4

C
Go to step 7

D
Go to step 9
A


2. INSPECT FRONT NO. 1 SPEAKERS
  1. Check the left and right front No. 1 speakers.

    HINT:
    1. for HATCHBACK (Click here )
    2. for SEDAN (Click here )

    OK:
    Front No. 1 speakers are normal.



NG
REPLACE FRONT NO. 1 SPEAKER
OK


3. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - FRONT NO. 1 SPEAKER)
  1. Disconnect the D10 radio receiver connector.

  1. Disconnect the front No. 1 speaker connector.

  1. I044961E04
    Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    D10-2 (FL+) - G6-1
    Below 1 Ω
    D10-6 (FL-) - G6-2
    Below 1 Ω
    D10-2 (FL+) - Body ground
    10 kΩ or higher
    D10-6(FL-) - Body ground
    10 kΩ or higher
    D10-1 (FR+) - F6-1
    Below 1 Ω
    D10-5 (FR-) - F6-2
    Below 1 Ω
    D10-1 (FR+) - Body ground
    10 kΩ or higher
    D10-1 (FR+) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

4. CHECK FRONT NO. 2 SPEAKERS
  1. Check whether sound is emitted from both the left and right front No. 2 speakers.

    OK:
    Sound is emitted from the speakers.



NG
Go to step 7
OK


5. CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER - FRONT NO. 2 SPEAKER)
  1. Disconnect the front No. 1 and front No. 2 connectors.

  1. E126349E01
    Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    F6-1 - D47-3
    Below 1 Ω
    F6-1 - Body ground
    10 kΩ or higher
    F6-2 - D47-1
    Below 1 Ω
    F6-2 - Body ground
    10 kΩ or higher
    G6-1 - D48-3
    Below 1 Ω
    G6-1 - Body ground
    10 kΩ or higher
    G6-2 - D48-1
    Below 1 Ω
    G6-2 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT FRONT NO. 2 SPEAKERS
  1. Disconnect the front No. 2 speaker connectors.

  1. E126350E01
    Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    1 - 2
    Below 1 Ω
    3 - 4
    Below 1 Ω
    1 - Body ground
    10 kΩ or higher
    3 - Body ground
    10 kΩ or higher



NG
REPLACE FRONT NO. 2 SPEAKER
OK

REPLACE FRONT NO. 1 SPEAKER

7. INSPECT FRONT NO. 2 SPEAKERS
  1. Check that the malfunction disappears when another speaker in good condition is installed.

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the left and right speakers.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.



OK
REPLACE FRONT NO. 2 SPEAKER
NG


8. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - FRONT NO. 2 SPEAKER)
  1. Disconnect the D10 radio receiver connector.

  1. Disconnect the front No. 2 speaker connectors.

  1. E126355E01
    Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    D10-2 (FL+) - D48-4
    Below 1 Ω
    D10-6 (FL-) - D48-2
    Below 1 Ω
    D10-2 (FL+) - Body ground
    10 kΩ or higher
    D10-6 (FL-) - Body ground
    10 kΩ or higher
    D10-1 (FR+) - D47-4
    Below 1 Ω
    D10-5 (FR-) - D47-2
    Below 1 Ω
    D10-1 (FR+) - Body ground
    10 kΩ or higher
    D10-5 (FR-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

9. INSPECT REAR SPEAKERS
  1. Check the left and right rear No. 1 speakers.

    HINT:
    1. for 5Dr HATCHBACK (Click here )
    2. for 3Dr HATCHBACK (Click here )
    3. for SEDAN (Click here )

    OK:
    Rear No. 1 speakers are normal.



NG
REPLACE REAR SPEAKER
OK


10. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - REAR NO. 1 SPEAKER)
  1. Disconnect the D11 radio receiver connector.

  1. Disconnect the rear speaker connectors.

  1. for HATCHBACK:

    1. I043620E03
      Measure the resistance.

      Standard Resistance:
      Tester Connection
      Specified Condition
      D11-2 (RL+) - J27-1 (I4-1)
      Below 1 Ω
      D11-6 (RL-) - J27-2 (I4-2)
      Below 1 Ω
      D11-2 (RL+) - Body ground
      10 kΩ or higher
      D11-6 (RL-) - Body ground
      10 kΩ or higher
      D11-1 (RR+) - J26-1 (H4-1)
      Below 1 Ω
      D11-3 (RR-) - J26-2 (H4-2)
      Below 1 Ω
      D11-1 (RR+) - Body ground
      10 kΩ or higher
      D11-3 (RR-) - Body ground
      10 kΩ or higher

  1. for SEDAN:

    1. C141219E01
      Measure the resistance.

      Standard Resistance:
      Tester Connection
      Specified Condition
      D11-2 (RL+) - J46-1
      Below 1 Ω
      D11-6 (RL-) - J46-2
      Below 1 Ω
      D11-2 (RL+) - Body ground
      10 kΩ or higher
      D11-6 (RL-) - Body ground
      10 kΩ or higher
      D11-1 (RR+) - J45-1
      Below 1 Ω
      D11-3 (RR-) - J45-2
      Below 1 Ω
      D11-1 (RR+) - Body ground
      10 kΩ or higher
      D11-3 (RR-) - Body ground
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE


← Speaker Circuit (Aug 2005 – Dec 2005)Radio Receiver Power Source Circuit (from Aug 2005) →