2005-2008 Yaris · Service Manual STEERING

Unable to Lock Steering Wheel

Circuit diagnosis · Vehicles built from Aug 2005

WIRING DIAGRAM

C117908E01

INSPECTION PROCEDURE

HINT:
Connect the intelligent tester to the DLC3 with the engine switch off, and turn any door courtesy switch ON and OFF at 1.5 second intervals until communication between the intelligent tester and the vehicle begins.


1. CHECK DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Read the DTCs of the certification ECU by following the prompts displayed on the intelligent tester.

    OK:
    No DTCs related to the certification ECU output.



NG
REPAIR OR REPLACE PARTS AND COMPONENTS INDICATED BY OUTPUT DTCS
OK


2. CHECK DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Read the DTCs of the main body ECU by following the prompts displayed on the intelligent tester.

OK:
No DTCs related to the main body ECU output.



NG
REPAIR OR REPLACE PARTS AND COMPONENTS INDICATED BY OUTPUT DTCS
OK


3. READ VALUE OF DATA LIST (LOCK/UNLOCK RECEIVE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Check the Data List of the certification ECU by following the prompts displayed on the intelligent tester.

    Result:
    Item
    Measurement Item/
    Range
    Normal Condition
    Lock / Unlock Receive
    Steering lock command reception record/
    YES or NO
    YES: Steering lock / unlock signal received
    NO: Steering lock / unlock signal not received



NO
Go to step 5
YES


4. INSPECT STEERING LOCK ACTUATOR ASSEMBLY (IGE - SGND VOLTAGE)

  1. C104383E01
    Turn the engine switch on (IG).

  1. Move the shift lever into the P position and turn the engine switch off.

  1. Open the driver door and immediately measure the voltage.

    Result:
    Tester Connection
    Result
    Proceed to
    IGE (D56-3) - SGND (D56-2)
    Decreases to less than 1 V
    A
    IGE (D56-3) - SGND (D56-2)
    Remains at 10 to 14 V
    B



B
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


5. CHECK STEERING LOCK (FUNCTION)
  1. Open the front passenger door.

  1. Lock the doors using the wireless remote door lock key.

  1. Check that no doors are locked and the steering lock does not operate.

    OK:
    No doors are locked and steering lock is not locked.



NG
GO TO WIRELESS DOOR LOCK CONTROL SYSTEM
OK


6. READ VALUE OF DATA LIST (S CODE CHECK)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Check the Data List of the certification ECU by following the prompts displayed on the intelligent tester.

    Result:
    Item
    Measurement Item/
    Range
    Normal Condition
    S Code Check
    S code match record/
    NG or OK
    NG: S code not matched
    OK: S code matched



OK
Go to step 8
NG


7. REPLACE ID CODE BOX
  1. Replace the ID code box with a normally functioning or new one.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Check the Data List of the certification ECU by following the prompts displayed on the intelligent tester.

    Result:
    Item
    Measurement Item/
    Range
    Normal Condition
    S Code Check
    S code match record/
    NG or OK
    NG: S code not matched
    OK: S code matched



OK
END
NG

REPLACE CERTIFICATION ECU

8. READ VALUE OF DATA LIST (L CODE CHECK)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Check the Data List of the certification ECU by following the prompts displayed on the intelligent tester.

    Result:
    Item
    Measurement Item/
    Range
    Normal Condition
    L Code Check
    L code match record/
    NG or OK
    NG: L code not matched
    OK: L code matched



OK
Go to step 10
NG


9. REPLACE ID CODE BOX
  1. Replace the ID code box with a normally functioning or new one.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Check the Data List of the certification ECU by following the prompts displayed on the intelligent tester.

    Result:
    Item
    Measurement Item/
    Range
    Normal Condition
    L Code Check
    L code match record/
    NG or OK
    NG: L code not matched
    OK: L code matched



OK
END
NG

REPLACE STEERING LOCK ACTUATOR ASSEMBLY

10. REPLACE STEERING LOCK ACTUATOR ASSEMBLY
  1. Replace the steering lock actuator assembly with a normally functioning or new one.

  1. Depress the brake pedal and then turn the engine switch on (IG).

  1. Check whether the steering lock can be released by turning the steering wheel, and check that the engine starts.

    OK:
    Steering lock is released and the engine starts.



OK
END
NG

REPLACE CERTIFICATION ECU


← Unable to Unlock Steering Wheel (from Aug 2005)Power Source Circuit (from Aug 2005) →