Front Fog Light Circuit
Circuit diagnosis · Vehicles built from Aug 2005
DESCRIPTION
When the front fog light switch is turned on, the front fog light relay illuminates the front fog lights.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. INSPECT WHETHER FRONT FOG LIGHTS ILLUMINATE |
Check whether the front fog lights illuminate.
- Result:
Condition
Proceed to
Neither left nor right fog light illuminates
A
Either left or right fog light illuminates
B
|
|
||||
| A | |
| 2. INSPECT FUSE (FR FOG, PANEL1*) |
Remove the FR FOG and PANEL1* fuses from the main body ECU.
Measure the resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the FR FOG and PANEL1* fuses.
- HINT:
- *: w/o Daytime running light system
|
|
||||
| OK | |
| 3. INSPECT FRONT FOG LIGHT RELAY |
Remove the front fog light relay.

Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
3 - 5
10 kΩ or higher
3 - 5
Below 1 Ω (Apply battery voltage to terminals 2 and 1)
Reinstall the front fog light relay.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (BATTERY - FRONT FOG LIGHT RELAY) |
Remove the front fog light relay.

Measure the voltage.
- Standard voltage:
Tester Connection
Condition
Specified Condition
2 - Body ground
Light control switch TAIL
10 to 14 V
5 - Body ground
Always
10 to 14 V
Reinstall the front fog light relay.
|
|
||||
| OK | |
| 5. INSPECT HEADLIGHT DIMMER SWITCH |
Remove the headlight dimmer switch.

Inspect the fog light switch.
Measure the resistance.
- Standard resistance:
- LHD and RHD for Europe:
Tester Connection
Condition
Specified Condition
3 (BFG) - 4 (LFG)
Fog light switch OFF
10 kΩ or higher
3 (BFG) - 4 (LFG)
Fog light switch ON
Below 1 Ω
- RHD except Europe:
Tester Connection
Condition
Specified Condition
1 (LFG) - 2 (BFG)
Fog light switch OFF
10 kΩ or higher
1 (LFG) - 2 (BFG)
Fog light switch ON
Below 1 Ω
Reinstall the headlight dimmer switch.
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (FRONT FOG LIGHT RELAY - HEADLIGHT DIMMER SWITCH) |
Disconnect the D4 headlight dimmer switch connector.

Measure the voltage.
- Standard voltage:
- LHD and RHD for Europe:
Tester Connection
Condition
Specified Condition
D4-3 (BFG) - Body ground
Always
10 to 14 V
- RHD except Europe:
Tester Connection
Condition
Specified Condition
D4-2 (BFG) - Body ground
Always
10 to 14 V
Reconnect the headlight dimmer switch connector.
|
|
||||
| OK | ||
| ||
| 7. INSPECT BULB (FRONT FOG LIGHT BULB) |
Remove the front fog light assembly.

Apply battery voltage to the terminals and check that the front fog light illuminates.
- Standard:
Measurement Condition
Standard
Positive battery - Terminal 2
Negative battery - Terminal 1
Front fog light illuminates
Reinstall the front fog light assembly.
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (FRONT FOG LIGHT RELAY - FRONT FOG LIGHT ASSEMBLY) |
Disconnect the B9 and B10 front fog light assembly connectors.

Measure the voltage.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
B9-2 - Body ground
Ignition switch on (IG)
Light control switch TAIL
Fog light switch ON
10 to 14 V
B10-2 - Body ground
Ignition switch on (IG)
Light control switch TAIL
Fog light switch ON
10 to 14 V
Reconnect the front fog light assembly connectors.
|
|
||||
| OK | ||
| ||
