Rear Fog Light Circuit
Circuit diagnosis · Vehicles built Aug 2005 – Oct 2006
Versions by build date: Aug 2005 – Oct 2006 from Nov 2006
DESCRIPTION
When the fog light switch is turned on, the rear fog light relay turns on to illuminate the rear fog light.WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. INSPECT FUSE (RR FOG, PANEL1*) |
 |
Remove the RR FOG and PANEL1* fuses from the main body ECU.
Measure the resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the RR FOG and PANEL1* fuses.
- HINT:
- *: w/o Daytime running light system
|
NG |
 |
|
|
|
| OK |
|
 |
|
| 2. INSPECT BULB (REAR FOG LIGHT BULB) |
 |
Remove the rear combination light assembly.
Apply battery voltage to the terminals and check that the rear fog light illuminates.
- Standard:
Measurement Condition
|
Standard
|
Positive battery - Terminal 2 Negative battery - Terminal 6
|
Rear fog light illuminates
|
Reinstall the rear combination light assembly.
|
NG |
 |
|
|
|
| OK |
|
 |
|
| 3. INSPECT HEADLIGHT DIMMER SWITCH |
 |
- Remove the headlight dimmer switch.
Inspect the fog light switch.
Measure the resistance.
- Standard resistance:
- Europe:
Tester Connection
|
Condition
|
Specified Condition
|
2 (B) - 3 (BFG) - 4 (LEG)
|
Fog light switch OFF
|
10 kΩor higher
|
2 (B) - 3 (BFG) - 4 (LEG)
|
Fog light switch ON
|
Below 1 Ω
|
- Australia:
Tester Connection
|
Condition
|
Specified Condition
|
1 (LFG) - 2 (BFG) - 3 (B)
|
Fog light switch OFF
|
10 kΩor higher
|
1 (LFG) - 2 (BFG) - 3 (B)
|
Fog light switch ON
|
Below 1 Ω
|
Reinstall the headlight dimmer switch.
|
NG |
 |
|
| REPLACE HEADLIGHT DIMMER SWITCH |
|
|
| OK |
|
 |
|
| 4. CHECK VEHICLE TYPE |
 |
Check whether the vehicle is equipped with the rear fog light relay.
- Result:
Rear fog light relay
|
Proceed to
|
without
|
A
|
with
|
B
|
|
B |
 |
|
|
|
| A |
|
 |
|
| 5. CHECK HARNESS AND CONNECTOR (FUSE - HEADLIGHT DIMMER SWITCH) |
 |
Disconnect the D4 headlight dimmer switch connector.
Measure the voltage.
- Standard voltage:
- Europe:
Tester Connection
|
Condition
|
Specified Condition
|
D4-2 (B) - Body ground
|
Always
|
10 to 14 V
|
- Australia:
Tester Connection
|
Condition
|
Specified Condition
|
D4-3 (B) - Body ground
|
Always
|
10 to 14 V
|
Reconnect the headlight dimmer switch connector.
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 6. CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH - REAR COMBINATION LIGHT) |
 |
Disconnect the D4 headlight dimmer switch connector.
Disconnect the J3 or J4 rear combination light assembly connectors.
Measure the resistance.
- Standard resistance:
- Europe (LHD):
Tester Connection
|
Specified Condition
|
D4-4 (LFG) - J4-2
|
Below 1 Ω
|
D4-4 (LFG) or J4-2 - Body ground
|
10 kΩ or higher
|
- Europe (RHD):
Tester Connection
|
Specified Condition
|
D4-4 (LFG) - J3-2
|
Below 1 Ω
|
D4-4 (LFG) or J3-2 - Body ground
|
10 kΩ or higher
|
- Australia:
Tester Connection
|
Specified Condition
|
D4-1 (LFG) - J3-2
|
Below 1 Ω
|
D4-1 (LFG) or J3-2 - Body ground
|
10 kΩ or higher
|
Reconnect the headlight dimmer switch connector.
Reconnect the rear combination light assembly connector.
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - BODY GROUND) |
|
| 7. INSPECT REAR FOG LIGHT RELAY |
 |
- Remove the rear fog light relay.
Measure the resistance.
- Standard resistance:
Tester Connection
|
Specified Condition
|
3 - 5
|
10 kΩor higher
|
3 - 5
|
Below 1 Ω (Battery voltage applied to terminals 1 and 2)
|
Reinstall the rear fog light relay.
|
NG |
 |
|
| REPLACE REAR FOG LIGHT RELAY |
|
|
| OK |
|
 |
|
| 8. CHECK HARNESS AND CONNECTOR (FUSE - REAR FOG LIGHT RELAY) |
 |
- Remove the rear fog light relay.
Measure the voltage.
- Standard voltage:
Tester Connection
|
Condition
|
Specified Condition
|
2 - Body ground
|
Light control switch TAIL
|
10 to 14 V
|
5 - Body ground
|
Always
|
10 to 14 V
|
Reinstall the rear fog light relay.
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 9. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - HEADLIGHT DIMMER SWITCH) |
 |
- Disconnect the D4 headlight dimmer switch connector.
Measure the voltage.
- Standard voltage:
- Europe:
Tester Connection
|
Condition
|
Specified Condition
|
D4-2 (B) - Body ground
|
Always
|
10 to 14 V
|
- Australia:
Tester Connection
|
Condition
|
Specified Condition
|
D4-3 (B) - Body ground
|
Always
|
10 to 14 V
|
Reconnect the headlight dimmer switch connector.
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 10. CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH - BODY GROUND) |
 |
- Disconnect the D4 headlight dimmer switch connector.
Measure the resistance.
- Standard resistance:
- Europe:
Tester Connection
|
Specified Condition
|
D4-4 (LFG) - Body ground
|
Below 1 Ω
|
- Australia:
Tester Connection
|
Specified Condition
|
D4-1 (LFG) - Body ground
|
Below 1 Ω
|
Reconnect the headlight dimmer switch connector.
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 11. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - REAR COMBINATION LIGHT ASSEMBLY) |
 |
- Disconnect the J3 or J4 rear combination light assembly connector.
Measure the voltage.
- Standard voltage:
- LHD:
Tester Connection
|
Condition
|
Specified Condition
|
J4-2 - Body ground
|
Ignition switch on (IG) Light control switch TAIL Fog light switch ON
|
10 to 14 V
|
- RHD:
Tester Connection
|
Condition
|
Specified Condition
|
J3-2 - Body ground
|
Ignition switch on (IG) Light control switch TAIL Fog light switch ON
|
10 to 14 V
|
Reconnect the rear combination light assembly connector.
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - BODY GROUND) |
|