Turn Signal Light Circuit
Circuit diagnosis · Vehicles built Aug 2005 – Oct 2006
Versions by build date: Aug 2005 – Oct 2006 from Nov 2006
DESCRIPTION
LHD models: The turn signal flasher relay in the main body ECU turns on when it receives signals from the headlight dimmer switch integrated with the turn signal switch, causing the turn signal lights to flash.RHD models: The turn signal flasher relay turns on when it receives signals from the headlight dimmer switch integrated with the turn signal switch, causing the turn signal lights to flash.
WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. INSPECT VEHICLE TYPE |
Check the vehicle type.
- Result:
Vehicle Type
Proceed to
LHD models
A
RHD models
B
|
|
||||
| A | |
| 2. CHECK OPERATION OF TURN SIGNAL LIGHT |
When the turn signal light switch is operated, check that the appropriate turn signal light flashes.
- Result:
Condition
Proceed to
No lights flash
A
Front turn signal light (LH or RH) does not flash
B
Side turn signal light (LH or RH) does not flash
C
Rear turn signal light (LH or RH) does not flash
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 3. INSPECT FUSE (GAUGE, HAZ) |
Remove the GAUGE fuse from the main body ECU.
Remove the HAZ fuse from the engine room relay block.
Measure the resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the GAUGE and HAZ fuses.
|
|
||||
| OK | |
| 4. INSPECT HEADLIGHT DIMMER SWITCH |
Remove the headlight dimmer switch.

Inspect the turn signal light switch.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
6 (TR) - 7 (E)
Right
Below 1 Ω
6 (TR) - 7 (E)
Neutral
10 kΩ or higher
5 (TL) - 7 (E)
Left
Below 1 Ω
5 (TL) - 7 (E)
Neutral
10 kΩ or higher
Reinstall the headlight dimmer switch.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (FUSE - MAIN BODY ECU) |
Disconnect the 4B main body ECU connector.

Measure the voltage.
- Standard voltage:
Tester Connection
Condition
Specified Condition
4B-32 - Body ground
Always
10 to 14 V
Reconnect the main body ECU connector.
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH - MAIN BODY ECU) |
Disconnect the D4 headlight dimmer switch connector.

Disconnect the 4S and 4E main body ECU connectors.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
D4-5 (TL) - 4S-11 (EL)
Below 1 Ω
D4-6 (TR) - 4S-12 (ER)
Below 1 Ω
D4-7 (E) - 4E-28 (GND)
Below 1 Ω
D4-5 (TL) or 4S-11 (EL) - Body ground
10 kΩ or higher
D4-6 (TR) or 4S-12 (ER) - Body ground
10 kΩ or higher
D4-7 (E) or 4E-28 (GND) - Body ground
10 kΩ or higher
Reconnect the headlight dimmer switch connector.
Reconnect the main body ECU connectors.
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND) |
Disconnect the 4E main body ECU connector.

Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
4E-17 (GND) - Body ground
Below 1 Ω
Reconnect the main body ECU connector.
|
|
||||
| OK | ||
| ||
| 8. INSPECT BULB (FRONT TURN SIGNAL BULB) |
Hatchback:
Remove the front turn signal light.

Apply battery voltage to the terminals and check that the front turn signal light illuminates.
- Standard:
Measurement Condition
Standard
Positive battery - Terminal 1
Negative battery - Terminal 2
Front turn signal light illuminates
Reinstall the front turn signal light.
Sedan:
Remove the front turn signal light.

Apply battery voltage to the terminals and check that the front turn signal light illuminates.
- Standard:
Measurement Condition
Standard
Positive battery - Terminal 1
Negative battery - Terminal 2
Front turn signal light illuminates
Reinstall the front turn signal light.
|
|
||||
| OK | |
| 9. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT TURN SIGNAL LIGHT BULB) |
Hatchback:

Disconnect the B1 and B8 front turn signal light connectors.
Disconnect the 4B main body ECU connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
4B-31 (LR) - B1-1
Below 1 Ω
4B-14 (LL) - B8-1
Below 1 Ω
4B-31 (LR) or B1-1 - Body ground
10 kΩ or higher
4B-14 (LL) or B8-1 - Body ground
10 kΩ or higher
Reconnect the front turn signal light connectors.
Reconnect the main body ECU connector.
Sedan:

Disconnect the B16 and B17 front turn signal light connectors.
Disconnect the 4B main body ECU connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
4B-31 (LR) - B16-1
Below 1 Ω
4B-14 (LL) - B17-1
Below 1 Ω
4B-31 (LR) or B16-1 - Body ground
10 kΩ or higher
4B-14 (LL) or B17-1 - Body ground
10 kΩ or higher
Reconnect the front turn signal light connectors.
Reconnect the main body ECU connector.
|
|
||||
| OK | ||
| ||
| 10. INSPECT BULB (SIDE TURN SIGNAL LIGHT BULB) |
Remove the side turn signal light assembly.

Apply battery voltage to the terminals and check that the side turn signal light illuminates.
- Standard:
Measurement Condition
Standard
Positive battery - Terminal 1
Negative battery - Terminal 2
Side turn signal light illuminates
Reinstall the side turn signal light assembly.
|
|
||||
| OK | |
| 11. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SIDE TURN SIGNAL LIGHT ASSEMBLY) |
Disconnect the A1 and A2 side turn signal light assembly connectors.

Disconnect the 4B main body ECU connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
4B-31 (LR) - A1-1
Below 1 Ω
4B-14 (LL) - A2-1
Below 1 Ω
4B-31 (LR) or A1-1 - Body ground
10 kΩ or higher
4B-14 (LL) or A2-1 - Body ground
10 kΩ or higher
Reconnect the side turn signal light assembly connectors.
Reconnect the main body ECU connector.
|
|
||||
| OK | ||
| ||
| 12. INSPECT BULB (REAR TURN SIGNAL LIGHT BULB) |
Hatchback:
Remove the rear combination light assembly.

Apply battery voltage to the terminals and check that the rear turn signal light illuminates.
- Standard:
Measurement Condition
Standard
Positive battery - Terminal 3
Negative battery - Terminal 6
Rear turn signal light illuminates
Reinstall the rear combination light assembly.
Sedan:
Remove the rear combination light assembly.

Apply battery voltage to the terminals and check that the rear turn signal light illuminates.
- Standard:
Measurement Condition
Standard
Positive battery - Terminal 2
Negative battery - Terminal 6
Rear turn signal light illuminates
Reinstall the rear combination light assembly.
|
|
||||
| OK | |
| 13. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REAR TURN SIGNAL LIGHT BULB) |
Hatchback:
Disconnect the J3 and J4 rear combination light assembly connectors.

Disconnect the 4A main body ECU connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
4A-28 (LR) - J3-3
Below 1 Ω
4A-27 (LL) - J4-3
Below 1 Ω
4A-28 (LR) or J3-3 - Body ground
10 kΩ or higher
4A-27 (LL) or J4-3 - Body ground
10 kΩ or higher
Reconnect the rear combination light assembly connectors.
Reconnect the main body ECU connector.
Sedan:
Disconnect the J41 and J42 rear combination light assembly connectors.

Disconnect the 4A main body ECU connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
4A-28 (LR) - J41-2
Below 1 Ω
4A-27 (LL) - J42-2
Below 1 Ω
4A-28 (LR) or J41-2 - Body ground
10 kΩ or higher
4A-27 (LL) or J42-2 Body ground
10 kΩ or higher
Reconnect the rear combination light assembly connectors.
Reconnect the main body ECU connector.
|
|
||||
| OK | ||
| ||
| 14. CHECK OPERATION OF TURN SIGNAL LIGHT |
When the turn signal light switch is operated, check that the appropriate turn signal light flashes.
- Result:
Condition
Proceed to
No lights flash
A
Front turn signal light (LH or RH) does not flash
B
Side turn signal light (LH or RH) does not flash
C
Rear turn signal light (LH or RH) does not flash
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 15. INSPECT FUSE (GAUGE, HAZ) |
Remove the GAUGE fuse from the main body ECU.
Remove the HAZ fuse from the engine room relay block.
Measure the resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the GAUGE and HAZ fuses.
|
|
||||
| OK | |
| 16. INSPECT TURN SIGNAL FLASHER RELAY |
Measure the voltage.

- Standard voltage:
Tester Connection
Condition
Specified Condition
D71-2 (LR) - Body ground
Turn signal switch (right turn) OFF → ON
0 V → 10 to 14 V (60 to 120 times per minute)
D71-3 (LL) - Body ground
Turn signal switch (left turn) OFF → ON
0 V → 10 to 14 V (60 to 120 times per minute)
D71-5 (EL) - Body ground
Turn signal switch (left turn) OFF → ON
10 to 14 V → 0 V
D71-6 (ER) - Body ground
Turn signal switch (right turn) OFF → ON
10 to 14 V → 0 V
|
|
||||
| OK | |
| 17. CHECK HARNESS AND CONNECTOR (FUSE - TURN SIGNAL FLASHER RELAY) |
Disconnect the D71 turn signal flasher relay connector.

Measure the voltage.
- Standard voltage:
Tester Connection
Condition
Specified Condition
D71-1(IG) - Body ground
Ignition switch on (IG)
10 to 14 V
D71-4 (B) - Body ground
Always
10 to 14 V
Reconnect the turn signal flasher relay connector.
|
|
||||
| OK | |
| 18. INSPECT HEADLIGHT DIMMER SWITCH |
Remove the headlight dimmer switch.

Inspect the turn signal light switch.
Measure the resistance.
- Standard resistance:
- Europe:
Tester Connection
Condition
Specified Condition
6 (TR) - 7 (E)
Right
Below 1 Ω
6 (TR) - 7 (E)
Neutral
10 kΩ or higher
5 (TL) - 7 (E)
Left
Below 1 Ω
5 (TL) - 7 (E)
Neutral
10 kΩ or higher
- Except Europe:
Tester Connection
Condition
Specified Condition
11 (E) - 13 (TR)
Right
Below 1 Ω
11 (E) - 13 (TR)
Neutral
10 kΩ or higher
11 (E) - 12 (TL)
Left
Below 1 Ω
11 (E) - 12 (TL)
Neutral
10 kΩ or higher
Reinstall the headlight dimmer switch.
|
|
||||
| OK | |
| 19. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER RELAY - HEADLIGHT DIMMER SWITCH) |
Disconnect the D4 headlight dimmer switch connector.

Disconnect the D71 turn signal flasher relay connector.
Measure the resistance.
- Standard resistance:
- Europe:
Tester Connection
Specified Condition
D4-5 (TL) - D71-5 (EL)
Below 1 Ω
D4-6 (TR) - D71-6 (ER)
Below 1 Ω
D4-7 (E) - D71-7 (E)
Below 1 Ω
D4-5 (TL) or D71-5 (EL) - Body ground
10 kΩ or higher
D4-6 (TR) or D71-6 (ER) - Body ground
10 kΩ or higher
D4-7 (E) or D71-7 (E) - Body ground
10 kΩ or higher
- Except Europe:
Tester Connection
Specified Condition
D4-11 (E) - D71-7 (E)
Below 1 Ω
D4-12 (TL) - D71-5 (EL)
Below 1 Ω
D4-13 (TR) - D71-6 (ER)
Below 1 Ω
D4-11 (E) or D71-7 (E) - Body ground
10 kΩ or higher
D4-12 (TL) or D71-5 (EL) - Body ground
10 kΩ or higher
D4-13 (TR) or D71-6 (ER) - Body ground
10 kΩ or higher
Reconnect the headlight dimmer switch connector.
Reconnect the turn signal flasher relay connector.
|
|
||||
| OK | |
| 20. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER RELAY - BODY GROUND) |
Disconnect the D71 turn signal flasher relay connector.

Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
D71-7 (E) - Body ground
Below 1 Ω
Reconnect the turn signal flasher relay connector.
|
|
||||
| OK | ||
| ||
| 21. INSPECT BULB (FRONT TURN SIGNAL LIGHT BULB) |
Hatchback:
Remove the front turn signal light.

Apply battery voltage to the terminals and check that the front turn signal light illuminates.
- Standard:
Measurement Condition
Standard
Positive battery - Terminal 1
Negative battery - Terminal 2
Front turn signal light illuminates
Reinstall the front turn signal light.
Sedan:
Remove the front turn signal light.

Apply battery voltage to the terminals and check that the front turn signal light illuminates.
- Standard:
Measurement Condition
Standard
Positive battery - Terminal 1
Negative battery - Terminal 2
Front turn signal light illuminates
Reinstall the front turn signal light.
|
|
||||
| OK | |
| 22. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER RELAY - FRONT TURN SIGNAL LIGHT) |
Hatchback:
Disconnect the D71 turn signal flasher relay connector.

Disconnect the B1 and B8 front turn signal light connectors.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
D71-2 (LR) - B1-1
Below 1 Ω
D71-3 (LL) - B8-1
Below 1 Ω
D71-2 (LR) or B1-1 - Body ground
10 kΩ or higher
D71-3 (LL) or B8-1 - Body ground
10 kΩ or higher
Reconnect the turn signal flasher relay connector.
Reconnect the front turn signal light connectors.
Sedan:
Disconnect the D71 turn signal flasher relay connector.

Disconnect the B16 and B17 front turn signal light connectors.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
D71-2 (LR) - B16-1
Below 1 Ω
D71-3 (LL) - B17-1
Below 1 Ω
D71-2 (LR) or B16-1 - Body ground
10 kΩ or higher
D71-3 (LL) or B17-1 - Body ground
10 kΩ or higher
Reconnect the turn signal flasher relay connector.
Reconnect the front turn signal light connectors.
|
|
||||
| OK | ||
| ||
| 23. INSPECT BULB (SIDE TURN SIGNAL BULB) |
Remove the side turn signal light assembly.

Apply battery voltage to the terminals and check that the side turn signal light illuminates.
- Standard:
Measurement Condition
Standard
Positive battery - Terminal 1
Negative battery - Terminal 2
Side turn signal light illuminates
Reinstall the side turn signal light assembly.
|
|
||||
| OK | |
| 24. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER RELAY - SIDE TURN SIGNAL LIGHT ASSEMBLY) |
Disconnect the D71 turn signal flasher relay connector.

Disconnect the A1 and A2 side turn signal light assembly connectors.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
D71-2 (LR) - A1-1
Below 1 Ω
D71-3 (LL) - A2-1
Below 1 Ω
D71-2 (LR) or A1-1 - Body ground
10 kΩ or higher
D71-3 (LL) or A2-1 - Body ground
10 kΩ or higher
Reconnect the turn signal flasher relay connector.
Reconnect the side turn signal light assembly connectors.
|
|
||||
| OK | ||
| ||
| 25. INSPECT BULB (REAR TURN SIGNAL BULB) |
Hatchback:
Remove the rear combination light assembly.

Apply battery voltage to the terminals and check that the rear turn signal light illuminates.
- Standard:
Measurement Condition
Standard
Positive battery - Terminal 3
Negative battery - Terminal 6
Rear turn signal light illuminates
Reinstall the rear combination light assembly.
Sedan:
Remove the rear combination light assembly.

Apply battery voltage to the terminals and check that the rear turn signal light illuminates.
- Standard:
Measurement Condition
Standard
Positive battery - Terminal 2
Negative battery - Terminal 6
Rear turn signal light illuminates
Reinstall the rear combination light assembly.
|
|
||||
| OK | |
| 26. CHECK HARNESS AND CONNECTOR (TURN FLASHER RELAY - REAR TURN SIGNAL LIGHT) |
Hatchback:
Disconnect the D71 turn signal flasher relay connector.

Disconnect the J3 and J4 rear combination light assembly connectors.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
D71-2 (LR) - J3-3
Below 1 Ω
D71-3 (LL) - J4-3
Below 1 Ω
D71-2 (LR) or J3-3 - Body ground
10 kΩ or higher
D71-3 (LL) or J4-3 - Body ground
10 kΩ or higher
Reconnect the turn signal flasher relay connector.
Reconnect the rear combination light assembly connectors.
Sedan:
Disconnect the D71 turn signal flasher relay connector.

Disconnect the J41 and J42 rear combination light assembly connectors.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
D71-2 (LR) - J41-2
Below 1 Ω
D71-3 (LL) - J42-2
Below 1 Ω
D71-2 (LR) or J41-2 - Body ground
10 kΩ or higher
D71-3 (LL) or J42-2 - Body ground
10 kΩ or higher
Reconnect the turn signal flasher relay connector.
Reconnect the rear combination light assembly connectors.
|
|
||||
| OK | ||
| ||
