2005-2008 Yaris · Service Manual BODY ELECTRICAL

Rear Fog Light Circuit

Circuit diagnosis · Vehicles built from Nov 2006

Versions by build date: Aug 2005 – Oct 2006 from Nov 2006

DESCRIPTION

When the fog light switch is turned on, the rear fog light relay turns on to illuminate the rear fog light.

WIRING DIAGRAM

E132070E02
B135310E03

INSPECTION PROCEDURE


1. INSPECT FUSE (RR FOG, PANEL1*)
  1. Remove the RR FOG and PANEL1* fuses from the main body ECU.

  1. Measure the resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the RR FOG and PANEL1* fuses.

HINT:
*: w/o Daytime running light system



NG
REPLACE FUSE
OK


2. INSPECT BULB (REAR FOG LIGHT BULB)

  1. B129860E01
    Except 2ZR-FE Engine:
    1. Remove the rear combination light assembly.

    2. Apply battery voltage to the terminals and check that the rear fog light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 2
      Negative battery - Terminal 6
      Rear fog light illuminates

    3. Reinstall the rear combination light assembly.

  1. B160039E04
    2ZR-FE Engine:
    1. Remove the rear fog light assembly.

    2. Apply battery voltage to the terminals and check that the rear fog light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 2
      Negative battery - Terminal 1
      Rear fog light illuminates



NG
REPLACE BULB
OK


3. INSPECT HEADLIGHT DIMMER SWITCH

  1. B126089E02
    Remove the headlight dimmer switch.

  1. Inspect the fog light switch.

  1. Measure the resistance.

    Standard resistance:
    Europe:
    Tester Connection
    Condition
    Specified Condition
    2 (B) - 3 (BFG) - 4 (LFG)
    Fog light switch OFF
    10 kΩor higher
    2 (B) - 3 (BFG) - 4 (LFG)
    Fog light switch ON
    Below 1 Ω
    Australia:
    Tester Connection
    Condition
    Specified Condition
    1 (LFG) - 2 (BFG) - 3 (B)
    Fog light switch OFF
    10 kΩor higher
    1 (LFG) - 2 (BFG) - 3 (B)
    Fog light switch ON
    Below 1 Ω

  1. Reinstall the headlight dimmer switch.



NG
REPLACE HEADLIGHT DIMMER SWITCH
OK


4. CHECK VEHICLE TYPE
  1. Check whether the vehicle is equipped with the rear fog light relay.

    Result:
    Rear fog light relay
    Proceed to
    without
    A
    with
    B



B
Go to step 7
A


5. CHECK HARNESS AND CONNECTOR (FUSE - HEADLIGHT DIMMER SWITCH)
B126090E07
  1. Disconnect the D4 headlight dimmer switch connector.

  1. Measure the voltage.

    Standard voltage:
    Europe:
    Tester Connection
    Condition
    Specified Condition
    D4-2 (B) - Body ground
    Always
    10 to 14 V
    Australia:
    Tester Connection
    Condition
    Specified Condition
    D4-3 (B) - Body ground
    Always
    10 to 14 V

  1. Reconnect the headlight dimmer switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH - REAR COMBINATION LIGHT)
E145043E01
  1. Disconnect the D4 headlight dimmer switch connector.

  1. Disconnect the J3 or J4 rear combination light assembly connectors.

  1. Measure the resistance.

    Standard resistance:
    Europe (LHD):
    Tester Connection
    Specified Condition
    D4-4 (LFG) - J4-2
    Below 1 Ω
    D4-4 (LFG) or J4-2 - Body ground
    10 kΩ or higher
    Europe (RHD):
    Tester Connection
    Specified Condition
    D4-4 (LFG) - J3-2
    Below 1 Ω
    D4-4 (LFG) or J3-2 - Body ground
    10 kΩ or higher
    Australia:
    Tester Connection
    Specified Condition
    D4-1 (LFG) - J3-2
    Below 1 Ω
    D4-1 (LFG) or J3-2 - Body ground
    10 kΩ or higher

  1. Reconnect the headlight dimmer switch connector.

  1. Reconnect the rear combination light assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - BODY GROUND)

7. INSPECT REAR FOG LIGHT RELAY

  1. E109078E04
    Remove the rear fog light relay.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩor higher
    3 - 5
    Below 1 Ω
    (Battery voltage applied to terminals 1 and 2)

  1. Reinstall the rear fog light relay.



NG
REPLACE REAR FOG LIGHT RELAY
OK


8. CHECK HARNESS AND CONNECTOR (FUSE - REAR FOG LIGHT RELAY)

  1. B125720E04
    Remove the rear fog light relay.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    2 - Body ground
    Light control switch TAIL
    10 to 14 V
    5 - Body ground
    Always
    10 to 14 V

  1. Reinstall the rear fog light relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - HEADLIGHT DIMMER SWITCH)

  1. B126090E02
    Disconnect the D4 headlight dimmer switch connector.

  1. Measure the voltage.

    Standard voltage:
    Europe:
    Tester Connection
    Condition
    Specified Condition
    D4-2 (B) - Body ground
    Always
    10 to 14 V
    Australia:
    Tester Connection
    Condition
    Specified Condition
    D4-3 (B) - Body ground
    Always
    10 to 14 V

  1. Reconnect the headlight dimmer switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH - BODY GROUND)

  1. B126090E03
    Disconnect the D4 headlight dimmer switch connector.

  1. Measure the resistance.

    Standard resistance:
    Europe:
    Tester Connection
    Specified Condition
    D4-4 (LFG) - Body ground
    Below 1 Ω
    Australia:
    Tester Connection
    Specified Condition
    D4-1 (LFG) - Body ground
    Below 1 Ω

  1. Reconnect the headlight dimmer switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. CHECK VEHICLE TYPE
  1. Check the engine type.

    Result:
    Vehicle type
    Proceed to
    Except 2ZR-FE engine
    A
    2ZR-FE engine
    B



B
Go to step 13
A


12. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - REAR COMBINATION LIGHT ASSEMBLY)

  1. B126092E04
    Disconnect the J3 or J4 rear combination light assembly connector.

  1. Measure the voltage.

    Standard voltage:
    LHD:
    Tester Connection
    Condition
    Specified Condition
    J4-2 - Body ground
    Ignition switch on (IG)
    Light control switch TAIL
    Fog light switch ON
    10 to 14 V
    RHD:
    Tester Connection
    Condition
    Specified Condition
    J3-2 - Body ground
    Ignition switch on (IG)
    Light control switch TAIL
    Fog light switch ON
    10 to 14 V

  1. Reconnect the rear combination light assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - BODY GROUND)

13. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - REAR FOG LIGHT ASSEMBLY)
E144620E01
  1. Disconnect the L5 and L6 rear fog light assembly connectors.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    L5-2 - Body ground
    Ignition switch on (IG)
    Light control switch TAIL
    Fog light switch ON
    10 to 14 V
    L6-2 - Body ground
    Ignition switch on (IG)
    Light control switch TAIL
    Fog light switch ON
    10 to 14 V

  1. Reconnect the rear fog light assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR FOG LIGHT ASSEMBLY - BODY GROUND)


← Rear Fog Light Circuit (Aug 2005 – Oct 2006)Turn Signal Light Circuit (Aug 2005 – Oct 2006) →