2005-2008 Yaris · Service Manual BODY ELECTRICAL

Turn Signal Light Circuit

Circuit diagnosis · Vehicles built from Nov 2006

Versions by build date: Aug 2005 – Oct 2006 from Nov 2006

DESCRIPTION

LHD models: The turn signal flasher relay in the main body ECU turns on when it receives signals from the headlight dimmer switch integrated with the turn signal switch, causing the turn signal lights to flash.
RHD models: The turn signal flasher relay turns on when it receives signals from the headlight dimmer switch integrated with the turn signal switch, causing the turn signal lights to flash.

WIRING DIAGRAM

B129618E04
B135327E02

INSPECTION PROCEDURE


1. INSPECT VEHICLE TYPE
  1. Check the vehicle type.

    Result:
    Vehicle Type
    Proceed to
    LHD models
    A
    RHD models
    B



B
Go to step 15
A


2. CHECK OPERATION OF TURN SIGNAL LIGHT
  1. When the turn signal light switch is operated, check that the appropriate turn signal light flashes.

    Result:
    Condition
    Proceed to
    No lights flash
    A
    Front turn signal light (LH or RH) does not flash
    B
    Side turn signal light (LH or RH) does not flash
    C
    Rear turn signal light (LH or RH) does not flash
    D



B
Go to step 8

C
Go to step 10

D
Go to step 12
A


3. INSPECT FUSE (GAUGE, HAZ)
  1. Remove the GAUGE fuse from the main body ECU.

  1. Remove the HAZ fuse from the engine room relay block.

  1. Measure the resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the GAUGE and HAZ fuses.



NG
REPLACE FUSE
OK


4. INSPECT HEADLIGHT DIMMER SWITCH

  1. E123010E16
    Remove the headlight dimmer switch.

  1. Inspect the turn signal light switch.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    6 (TR) - 7 (E)
    Right
    Below 1 Ω
    6 (TR) - 7 (E)
    Neutral
    10 kΩ or higher
    5 (TL) - 7 (E)
    Left
    Below 1 Ω
    5 (TL) - 7 (E)
    Neutral
    10 kΩ or higher

  1. Reinstall the headlight dimmer switch.



NG
REPLACE HEADLIGHT DIMMER SWITCH
OK


5. CHECK HARNESS AND CONNECTOR (FUSE - MAIN BODY ECU)

  1. B135312E01
    Disconnect the 4B main body ECU connector.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    4B-32 - Body ground
    Always
    10 to 14 V

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH - MAIN BODY ECU)

  1. B135313E01
    Disconnect the D4 headlight dimmer switch connector.

  1. Disconnect the 4E and 4S main body ECU connectors.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    D4-5 (TL) - 4S-11 (EL)
    Below 1 Ω
    D4-6 (TR) - 4S-12 (ER)
    Below 1 Ω
    D4-7 (E) - 4E-28 (GND)
    Below 1 Ω
    D4-5 (TL) or 4S-11 (EL) - Body ground
    10 kΩ or higher
    D4-6 (TR) or 4S-12 (ER) - Body ground
    10 kΩ or higher
    D4-7 (E) or 4E-28 (GND) - Body ground
    10 kΩ or higher

  1. Reconnect the headlight dimmer switch connector.

  1. Reconnect the main body ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)

  1. B135314E01
    Disconnect the 4E main body ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    4E-17 (GND) - Body ground
    Below 1 Ω

  1. Reconnect the main body ECU connector.



OK
Go to step 14

NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
8. INSPECT BULB (FRONT TURN SIGNAL BULB)

  1. Hatchback:

    1. B129905E01
      Remove the front turn signal light.

    2. Apply battery voltage to the terminals and check that the front turn signal light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 1
      Negative battery - Terminal 2
      Front turn signal light illuminates

    3. Reinstall the front turn signal light.

  1. Sedan:

    1. B144226E04
      Remove the front turn signal light.

    2. Apply battery voltage to the terminals and check that the front turn signal light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 1
      Negative battery - Terminal 2
      Front turn signal light illuminates

    3. Reinstall the front turn signal light.



NG
REPLACE BULB
OK


9. CHECK HARNESS AND CONNECTOR (FRONT TURN SIGNAL LIGHT BULB - MAIN BODY ECU, BODY GROUND)

  1. B135315E02
    Hatchback:
    1. Disconnect the B1 and B8 front turn signal light connectors.

    2. Disconnect the 4B main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4B-31 (LR) - B1-1
      Below 1 Ω
      4B-14 (LL) - B8-1
      Below 1 Ω
      4B-31 (LR) or B1-1 - Body ground
      10 kΩ or higher
      4B-14 (LL) or B8-1 - Body ground
      10 kΩ or higher
      B1-2 - Body ground
      Below 1 Ω
      B8-2 - Body ground
      Below 1 Ω

    4. Reconnect the front turn signal light connectors.

    5. Reconnect the main body ECU connector.

  1. B144227E04
    Sedan:
    1. Disconnect the B16 and B17 front turn signal light connectors.

    2. Disconnect the 4B main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4B-31 (LR) - B16-1
      Below 1 Ω
      4B-14 (LL) - B17-1
      Below 1 Ω
      4B-31 (LR) or B16-1 - Body ground
      10 kΩ or higher
      4B-14 (LL) or B17-1 - Body ground
      10 kΩ or higher
      B16-2 - Body ground
      Below 1 Ω
      B17-2 - Body ground
      Below 1 Ω

    4. Reconnect the front turn signal light connectors.

    5. Reconnect the main body ECU connector.



OK
Go to step 14

NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
10. INSPECT BULB (SIDE TURN SIGNAL LIGHT BULB)

  1. B129906E01
    Remove the side turn signal light assembly.

  1. Apply battery voltage to the terminals and check that the side turn signal light illuminates.

    Standard:
    Measurement Condition
    Standard
    Positive battery - Terminal 1
    Negative battery - Terminal 2
    Side turn signal light illuminates

  1. Reinstall the side turn signal light assembly.



NG
REPLACE BULB
OK


11. CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY - MAIN BODY ECU, BODY GROUND)

  1. B135316E02
    Disconnect the A1 and A2 side turn signal light assembly connectors.

  1. Disconnect the 4B main body ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    4B-31 (LR) - A1-1
    Below 1 Ω
    4B-14 (LL) - A2-1
    Below 1 Ω
    4B-31 (LR) or A1-1 - Body ground
    10 kΩ or higher
    4B-14 (LL) or A2-1 - Body ground
    10 kΩ or higher
    A1-2 - Body ground
    Below 1 Ω
    A2-2 - Body ground
    Below 1 Ω

  1. Reconnect the side turn signal light assembly connectors.

  1. Reconnect the main body ECU connector.



OK
Go to step 14

NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
12. INSPECT BULB (REAR TURN SIGNAL LIGHT BULB)

  1. Hatchback (Except 2ZR-FE Engine):

    1. B129860E04
      Remove the rear combination light assembly.

    2. Apply battery voltage to the terminals and check that the rear turn signal light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 3
      Negative battery - Terminal 6
      Rear turn signal light illuminates

    3. Reinstall the rear combination light assembly.

  1. Sedan, Hatchback (2ZR-FE Engine):

    1. B141033E01
      Remove the rear combination light assembly.

    2. Apply battery voltage to the terminals and check that the rear turn signal light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 2
      Negative battery - Terminal 6
      Rear turn signal light illuminates

    3. Reinstall the rear combination light assembly.



NG
REPLACE BULB
OK


13. CHECK HARNESS AND CONNECTOR (REAR TURN SIGNAL LIGHT BULB - MAIN BODY ECU, BODY GROUND)

  1. Hatchback (Except 2ZR-FE Engine):

    1. B131873E04
      Disconnect the J3 and J4 rear combination light assembly connectors.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4A-28 (LR) - J3-3
      Below 1 Ω
      4A-27 (LL) - J4-3
      Below 1 Ω
      4A-28 (LR) or J3-3 - Body ground
      10 kΩ or higher
      4A-27 (LL) or J4-3 - Body ground
      10 kΩ or higher
      J3-3 - Body ground
      Below 1 Ω
      J4-3 - Body ground
      Below 1 Ω

    4. Reconnect the rear combination light assembly connectors.

    5. Reconnect the main body ECU connector.

  1. Sedan:

    1. B141726E01
      Disconnect the J41 and J42 rear combination light assembly connectors.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4A-28 (LR) - J41-2
      Below 1 Ω
      4A-27 (LL) - J42-2
      Below 1 Ω
      4A-28 (LR) or J41-2 - Body ground
      10 kΩ or higher
      4A-27 (LL) or J42-2 Body ground
      10 kΩ or higher
      J41-6 - Body ground
      Below 1 Ω
      J42-6 - Body ground
      Below 1 Ω

    4. Reconnect the rear combination light assembly connectors.

    5. Reconnect the main body ECU connector.

  1. B141726E08
    Hatchback (2ZR-FE Engine):
    1. Disconnect the J52 and J53 rear combination light assembly connectors.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4A-28 (LR) - J52-2
      Below 1 Ω
      4A-27 (LL) - J53-2
      Below 1 Ω
      4A-28 (LR) or J52-2 - Body ground
      10 kΩ or higher
      4A-27 (LL) or J53-2 Body ground
      10 kΩ or higher
      J53-6 - Body ground
      Below 1 Ω
      J54-6 - Body ground
      Below 1 Ω

    4. Reconnect the rear combination light assembly connectors.

    5. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14. INSPECT MAIN BODY ECU
E145777E05
  1. Remove the main body ECU.

  1. Remove the turn signal light relay from the main body ECU.

  1. Remove the IG1 relay from the main body ECU.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    Turn signal flasher relay terminal 1 (IG) - IG1 relay terminal 3
    Below 1 Ω
    Turn signal flasher relay terminal 2 (LR) - 4A-28 - 4B-31
    Below 1 Ω
    Turn signal flasher relay terminal 3 (LL) - 4A-27 - 4B-14
    Below 1 Ω
    Turn signal flasher relay terminal 4 (+B) - 4B-32
    Below 1 Ω
    Turn signal flasher relay terminal 5 (EL) - 4S-11
    Below 1 Ω
    Turn signal flasher relay terminal 6 (ER) - 4S-12
    Below 1 Ω
    Turn signal flasher relay terminal 7 (GND) - 4E-17 - 4E-28
    Below 1 Ω

  1. Reinstall the IG1 relay.

  1. Reinstall the turn signal flasher relay

  1. Reinstall the main body ECU.



NG
REPLACE MAIN BODY ECU
OK

REPLACE TURN SIGNAL FLASHER RELAY

15. CHECK OPERATION OF TURN SIGNAL LIGHT
  1. When the turn signal light switch is operated, check that the appropriate turn signal light flashes.

    Result:
    Condition
    Proceed to
    No lights flash
    A
    Front turn signal light (LH or RH) does not flash
    B
    Side turn signal light (LH or RH) does not flash
    C
    Rear turn signal light (LH or RH) does not flash
    D



B
Go to step 22

C
Go to step 24

D
Go to step 26
A


16. INSPECT FUSE (GAUGE, HAZ)
  1. Remove the GAUGE fuse from the main body ECU.

  1. Remove the HAZ fuse from the engine room relay block.

  1. Measure the resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the GAUGE and HAZ fuses.



NG
REPLACE FUSE
OK


17. INSPECT TURN SIGNAL FLASHER RELAY

  1. E101506E03
    Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D71-2 (LR) - Body ground
    Turn signal switch (right turn) OFF → ON
    0 V → 10 to 14 V (60 to 120 times per minute)
    D71-3 (LL) - Body ground
    Turn signal switch (left turn) OFF → ON
    0 V → 10 to 14 V (60 to 120 times per minute)
    D71-5 (EL) - Body ground
    Turn signal switch (left turn) OFF → ON
    10 to 14 V → 0 V
    D71-6 (ER) - Body ground
    Turn signal switch (right turn) OFF → ON
    10 to 14 V → 0 V



NG
REPLACE TURN SIGNAL FLASHER RELAY
OK


18. CHECK HARNESS AND CONNECTOR (FUSE - TURN SIGNAL FLASHER RELAY)

  1. E120966E01
    Disconnect the D71 turn signal flasher relay connector.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D71-1(IG) - Body ground
    Ignition switch on (IG)
    10 to 14 V
    D71-4 (B) - Body ground
    Always
    10 to 14 V

  1. Reconnect the turn signal flasher relay connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


19. INSPECT HEADLIGHT DIMMER SWITCH

  1. B126089E06
    Remove the headlight dimmer switch.

  1. Inspect the turn signal light switch.

  1. Measure the resistance.

    Standard resistance:
    Europe:
    Tester Connection
    Condition
    Specified Condition
    6 (TR) - 7 (E)
    Right
    Below 1 Ω
    6 (TR) - 7 (E)
    Neutral
    10 kΩ or higher
    5 (TL) - 7 (E)
    Left
    Below 1 Ω
    5 (TL) - 7 (E)
    Neutral
    10 kΩ or higher
    Except Europe:
    Tester Connection
    Condition
    Specified Condition
    11 (E) - 13 (TR)
    Right
    Below 1 Ω
    11 (E) - 13 (TR)
    Neutral
    10 kΩ or higher
    11 (E) - 12 (TL)
    Left
    Below 1 Ω
    11 (E) - 12 (TL)
    Neutral
    10 kΩ or higher

  1. Reinstall the headlight dimmer switch.



NG
REPLACE HEADLIGHT DIMMER SWITCH
OK


20. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER RELAY - HEADLIGHT DIMMER SWITCH)

  1. B129621E02
    Disconnect the D4 headlight dimmer switch connector.

  1. Disconnect the D71 turn signal flasher relay connector.

  1. Measure the resistance.

    Standard resistance:
    Europe:
    Tester Connection
    Specified Condition
    D4-5 (TL) - D71-5 (EL)
    Below 1 Ω
    D4-6 (TR) - D71-6 (ER)
    Below 1 Ω
    D4-7 (E) - D71-7 (E)
    Below 1 Ω
    D4-5 (TL) or D71-5 (EL) - Body ground
    10 kΩ or higher
    D4-6 (TR) or D71-6 (ER) - Body ground
    10 kΩ or higher
    D4-7 (E) or D71-7 (E) - Body ground
    10 kΩ or higher
    Except Europe:
    Tester Connection
    Specified Condition
    D4-11 (E) - D71-7 (E)
    Below 1 Ω
    D4-12 (TL) - D71-5 (EL)
    Below 1 Ω
    D4-13 (TR) - D71-6 (ER)
    Below 1 Ω
    D4-11 (E) or D71-7 (E) - Body ground
    10 kΩ or higher
    D4-12 (TL) or D71-5 (EL) - Body ground
    10 kΩ or higher
    D4-13 (TR) or D71-6 (ER) - Body ground
    10 kΩ or higher

  1. Reconnect the headlight dimmer switch connector.

  1. Reconnect the turn signal flasher relay connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


21. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER RELAY - BODY GROUND)

  1. E120966E03
    Disconnect the D71 turn signal flasher relay connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    D71-7 (E) - Body ground
    Below 1 Ω

  1. Reconnect the turn signal flasher relay connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT DIMMER SWITCH - BODY GROUND)

22. INSPECT BULB (FRONT TURN SIGNAL LIGHT BULB)

  1. Hatchback:

    1. B129905E01
      Remove the front turn signal light.

    2. Apply battery voltage to the terminals and check that the front turn signal light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 1
      Negative battery - Terminal 2
      Front turn signal light illuminates

    3. Reinstall the front turn signal light.

  1. Sedan:

    1. B144226E04
      Remove the front turn signal light.

    2. Apply battery voltage to the terminals and check that the front turn signal light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 1
      Negative battery - Terminal 2
      Front turn signal light illuminates

    3. Reinstall the front turn signal light.



NG
REPLACE BULB
OK


23. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER RELAY - FRONT TURN SIGNAL LIGHT)

  1. Hatchback:

    1. B126125E02
      Disconnect the D71 turn signal flasher relay connector.

    2. Disconnect the B1 and B8 front turn signal light connectors.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      D71-2 (LR) - B1-1
      Below 1 Ω
      D71-3 (LL) - B8-1
      Below 1 Ω
      D71-2 (LR) or B1-1 - Body ground
      10 kΩ or higher
      D71-3 (LL) or B8-1 - Body ground
      10 kΩ or higher

    4. Reconnect the turn signal flasher relay connector.

    5. Reconnect the front turn signal light connectors.

  1. Sedan:

    1. B146368E01
      Disconnect the D71 turn signal flasher relay connector.

    2. Disconnect the B16 and B17 front turn signal light connectors.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      D71-2 (LR) - B16-1
      Below 1 Ω
      D71-3 (LL) - B17-1
      Below 1 Ω
      D71-2 (LR) or B16-1 - Body ground
      10 kΩ or higher
      D71-3 (LL) or B17-1 - Body ground
      10 kΩ or higher

    4. Reconnect the turn signal flasher relay connector.

    5. Reconnect the front turn signal light connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT TURN SIGNAL LIGHT - BODY GROUND)

24. INSPECT BULB (SIDE TURN SIGNAL BULB)

  1. B129906E01
    Remove the side turn signal light assembly.

  1. Apply battery voltage to the terminals and check that the side turn signal light illuminates.

    Standard:
    Measurement Condition
    Standard
    Positive battery - Terminal 1
    Negative battery - Terminal 2
    Side turn signal light illuminates

  1. Reinstall the side turn signal light assembly.



NG
REPLACE BULB
OK


25. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER RELAY - SIDE TURN SIGNAL LIGHT ASSEMBLY)

  1. B126127E02
    Disconnect the D71 turn signal flasher relay connector.

  1. Disconnect the A1 and A2 side turn signal light assembly connectors.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    D71-2 (LR) - A1-1
    Below 1 Ω
    D71-3 (LL) - A2-1
    Below 1 Ω
    D71-2 (LR) or A1-1 - Body ground
    10 kΩ or higher
    D71-3 (LL) or A2-1 - Body ground
    10 kΩ or higher

  1. Reconnect the turn signal flasher relay connector.

  1. Reconnect the side turn signal light assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY - BODY GROUND)

26. INSPECT BULB (REAR TURN SIGNAL BULB)

  1. Hatchback (Except 2ZR-FE Engine):

    1. B129860E04
      Remove the rear combination light assembly.

    2. Apply battery voltage to the terminals and check that the rear turn signal light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 3
      Negative battery - Terminal 6
      Rear turn signal light illuminates

    3. Reinstall the rear combination light assembly.

  1. Sedan, Hatchback (2ZR-FE Engine):

    1. B141033E01
      Remove the rear combination light assembly.

    2. Apply battery voltage to the terminals and check that the rear turn signal light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 2
      Negative battery - Terminal 6
      Rear turn signal light illuminates

    3. Reinstall the rear combination light assembly.



NG
REPLACE BULB
OK


27. CHECK HARNESS AND CONNECTOR (TURN FLASHER RELAY - REAR TURN SIGNAL LIGHT)

  1. Hatchback (Except 2ZR-FE Engine):

    1. B126126E02
      Disconnect the D71 turn signal flasher relay connector.

    2. Disconnect the J3 and J4 rear combination light assembly connectors.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      D71-2 (LR) - J3-3
      Below 1 Ω
      D71-3 (LL) - J4-3
      Below 1 Ω
      D71-2 (LR) or J3-3 - Body ground
      10 kΩ or higher
      D71-3 (LL) or J4-3 - Body ground
      10 kΩ or higher

    4. Reconnect the turn signal flasher relay connector.

    5. Reconnect the rear combination light assembly connectors.

  1. Sedan:

    1. B141728E01
      Disconnect the D71 turn signal flasher relay connector.

    2. Disconnect the J41 and J42 rear combination light assembly connectors.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      D71-2 (LR) - J41-2
      Below 1 Ω
      D71-3 (LL) - J42-2
      Below 1 Ω
      D71-2 (LR) or J41-2 - Body ground
      10 kΩ or higher
      D71-3 (LL) or J42-2 - Body ground
      10 kΩ or higher

    4. Reconnect the turn signal flasher relay connector.

    5. Reconnect the rear combination light assembly connectors.

  1. B141728E03
    Hatchback (2ZR-FE Engine)
    1. Disconnect the D71 turn signal flasher relay connector.

    2. Disconnect the J52 and J53 rear combination light assembly connectors.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      D71-2 (LR) - J52-2
      Below 1 Ω
      D71-3 (LL) - J53-2
      Below 1 Ω
      D71-2 (LR) or J52-2 - Body ground
      10 kΩ or higher
      D71-3 (LL) or J53-2 - Body ground
      10 kΩ or higher

    4. Reconnect the turn signal flasher relay connector.

    5. Reconnect the rear combination light assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - BODY GROUND)


← Turn Signal Light Circuit (Aug 2005 – Oct 2006)Hazard Warning Switch Circuit (from Aug 2005) →