2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL CYLINDER HEAD GASKET

G035831

  1. Inspect the protrusion height of the piston heads.

    1. Place a dial indicator on the cylinder block as shown in the illustration.

      NOTICE:
      Make sure that the dial indicator is at right angles to the cylinder block top surface.

    2. G035832E01
      Measure the protrusion height of the piston head of each cylinder at 2 place as shown in the illustration.

  1. G036742E01
    Select a new cylinder head gasket.

    1. Select the highest protrusion height among the 8 measurement records. Use it to select a new cylinder head gasket.

      Piston protrusion:
      Piston protrusion mm (in.)
      Gasket cutout
      Gasket size
      0.375 to 0.425
      (0.015 to 0.018 in.)
      1
      A
      0.425 to 0.475
      (0.018 to 0.019 in.)
      2
      B
      0.475 to 0.525
      (0.019 to 0.021 in.)
      3
      C
      0.525 to 0.575
      (0.021 to 0.023 in.)
      4
      D
      0.575 to 0.625
      (0.023 to 0.025 in.)
      5
      E

  1. Install the cylinder head gasket.

    1. Apply seal packing (Diameter 3.5 to 4.5 mm (0.138 to 0.177 in.)) to the cylinder block side shown in the illustration.

      Seal packing:
      Part No. 08826-00080 or the equivalent

      NOTICE:
      Remove any oil from the contact surface.

    2. Place a new cylinder head gasket on the cylinder block with the Lot No. stamp facing upward.

    3. Apply seal packing (Diameter 3.5 to 4.5 mm (0.138 to 0.177 in.)) to the top surface of the cylinder head again as shown in the illustration.

      Seal packing:
      Part No. 08826-00080 or the equivalent

    4. Install the cylinder head onto the cylinder block.

      A125833E01

      NOTICE:
      1. Remove any oil from the contact surface.
      2. Install the cylinder head within 3 minutes, and tighten the bolts within 15 minutes of applying the seal packing.


2. INSTALL CYLINDER HEAD SUB-ASSEMBLY

A069374E01

HINT:
The cylinder heat bolts are tightened in 2 successive steps.

  1. Apply a light coat of engine oil to the threads of the cylinder head bolts.

  1. Using several steps, uniformly install and tighten the 10 cylinder head bolts and plate washers in the sequence shown in the illustration. (*1)

    Torque:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }

  1. A125835E01
    Mark the front of the cylinder head bolts with paint.

  1. Using the same sequence as step (*1), retighten the cylinder head bolts by an additional 90° as shown in the illustration.

  1. Check that each paint mark is now 180° from the front.

  1. Connect each connector and wire harness to the cylinder head.

  1. A128789
    Install the water by-pass pipe with the bolt.

    Torque:
    9 N*m{ 92 kgf*cm , 80 ft.*lbf }

  1. Install the water temperature sensor.

    SST
    09817-33190  

  1. A128788
    Connect the radiator inlet hose and the heater water hose.

  1. A125777
    Connect the vacuum hose shown in the illustration.


3. INSTALL OIL LEVEL GAGE GUIDE
  1. Apply engine oil to a new O-ring, then install it onto the oil level gage guide.

  1. Install the oil level gage guide with the bolt.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Install the oil level gage.


4. INSTALL VALVE ROCKER ARM SUB-ASSEMBLY NO. 1

G035835
  1. Apply engine oil to the stem end cap, valve rocker arm pivot top surface and valve rocker arm roller portion.

  1. Install the 8 valve rocker arms.


5. INSTALL CAMSHAFT

G035836E01
  1. Turn the crankshaft to set the key in the 70° BTDC position.

  1. Apply engine oil to the camshaft journal portion and cam portion.

  1. G035837
    Examine the front marks and numbers and check that the sequence order is as shown in the illustration. Then, temporarily tighten the camshaft with the camshaft beating caps and bolts.

    NOTICE:
    Do not tilt the valve rocker arm when installing the camshaft onto the cylinder head.

  1. G035811E02
    Using several steps, temporarily tighten the bolts in the sequence shown in the illustration, and then tighten the bolts to the specified torque.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


6. INSTALL CHAIN SUB-ASSEMBLY

G035839E01
  1. Turn the camshaft to set the straight pin in the position shown in the illustration.

    NOTICE:
    When turning the camshaft to set the pin in the position, turn the crankshaft to set the key in the 70° BTDC position.

  1. G036406E01
    Turn the crankshaft to set the key in the position shown in the illustration.

  1. A125837E01
    Align the yellow mark plate on the chain with the timing marks on the camshaft timing sprocket and crankshaft timing sprocket.

  1. A125838E01
    Install the chain, camshaft timing sprocket and crankshaft timing sprocket together onto the engine.

  1. G035809E01
    Fix the camshaft timing sprocket, using SST and install the camshaft timing sprocket with the 3 bolts.
    SST
    09960-10010  

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


7. INSTALL CHAIN VIBRATION DAMPER NO. 1

A099124
  1. Install the chain vibration damper with the 2 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


8. INSTALL CHAIN TENSIONER SLIPPER

A099123
  1. Install the chain tensioner slipper onto the cylinder block.


9. INSTALL CHAIN TENSIONER ASSEMBLY NO. 1

A125803E01
  1. Pull up the stopper plate to unlock the plunger.

  1. Push in the plunger to the end with plunger unlocked.

  1. A125804E01
    Pull down the stopper plate with the plunger pushed to the end to lock the plunger.

  1. A087621
    Insert a 2.5 mm (0.098 in.) diameter bar into the hole in the stopper plate with the plunger locked.

    HINT:
    If the stopper plate is not completely pulled down and a 2.5 mm (0.098 in.) diameter bar cannot be inserted, unlock and pull out the plunger slightly. The stopper plate can then be completely pulled down and a 2.5 mm (0.098 in.) diameter bar can be inserted easily.

  1. A099122
    install the chain tensioner with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Remove the 2.5 mm (0.098 in.) diameter bar from the chain tensioner.

  1. A125838E01
    Check that the mark plates and timing marks are in the positions shown in the illustration.


10. INSTALL OIL PUMP SEAL

  1. A069812E01
    Using SST and a hammer, tap in the new oil seal until its surface is flush with the oil pump edge.
    SST
    09223-22010  

    NOTICE:
    Tap in the oil seal vertically.

  1. Apply MP grease to a new oil seal lip.

    NOTICE:
    Keep the lip free of foreign objects.


11. INSTALL OIL PUMP ASSEMBLY

  1. A099119
    Install 2 new O-rings onto the 2 portions as shown in the illustration.

  1. Apply seal packing to the engine body and oil pump as shown in the illustration below.

    Seal packing:
    Part No. 08826-00100 or equivalent for Water pump
    Part No. 08826-00080 or equivalent for othes

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan within 3 minutes, and tighten the bolts within 15 minutes of applying seal packing.


    A125840E01

  1. A069333
    Align the keyway of the oil pump drive rotor with the rectangular portion of the crankshaft, then slide the oil pump into place.

  1. A099117E02
    Install the oil pump assembly with the 16 bolts and nut as shown in the illustration.

    Torque:
    Bolt A:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }
    Bolt B:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }
    Bolt C:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }
    Bolt D:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }
    Nut:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    NOTICE:
    1. Be careful not to let the chain come into contact with the seal packing when installing the oil pump.
    2. Install the engine mounting bracket RH and water pump within 15 minutes of installing the oil pump.

    HINT:
    The bolt lengths are as follows.
    Bolt A: 20 mm (0.79 in.)
    Bolt B: 30 mm (1.18 in.)
    Bolt C: 35 mm (1.38 in.)
    Bolt D (double ended bolt): 20 and 14 mm (0.79 and 0.55 in.)


12. INSTALL TIMING CHAIN COVER NO. 2

A069329
  1. Install the timing cover No. 2 with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


13. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

A125792
  1. Install the engine mounting bracket with the 4 bolts.

    Torque:
    55 N*m{ 561 kgf*cm , 41 in.*lbf }


14. INSTALL CRANK SHAFT DAMPER SUB-ASSEMBLY

A099115
  1. Align the key with the key groove of the crankshaft damper, and slide the crankshaft damper to the crankshaft.

  1. Using SST, fix the crankshaft damper.

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Tighten the bolt to the specified torque.

    Torque:
    180 N*m{ 1,835 kgf*cm , 133 ft.*lbf }


15. INSTALL VACUUM PUMP ASSEMBLY

F048854
  1. Coat 2 new O-rings with engine oil, and place them onto the vacuum pump.

  1. F048844
    Apply engine oil to the oil pipe at the tip of the vacuum pump.

  1. C129750E01
    Install the vacuum pump so that the coupling teeth A on the side of the vacuum pump can engage with the tip groove of camshaft B.

  1. C129749
    Install 2 new bolts onto the vacuum pump.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. C129748
    Connect the vacuum hose with the clip to the vacuum pump.

  1. Connect the cam position sensor connector.


16. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

G035854E01
  1. Apply seal packing to the 4 locations as shown in the illustration, then install the cylinder head cover.

    Seal packing:
    Part No. 08826-00080 or the equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the cylinder head cover within 3 minutes, and tighten the bolts within 15 minutes of applying the seal packing.

  1. G036743
    Temporarily tighten the cylinder head cover with the 12 bolts.

  1. Tighten the 12 bolts to the specified torque as shown in the illustration.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. A125694
    Install the connector to vacuum reservoir tube with the 2 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. A125689
    Connect the ventilation hose to the cylinder head.

  1. A125693
    Connect the vacuum hose shown in the illustration.

  1. A125692
    Connect the 3 vacuum hoses shown in the illustration.

  1. A125688
    Connect the hose shown in the illustration.

  1. A125691
    Connect the hose shown in the illustration.

  1. G036391E01
    Install the 3 bolts and wire harness clamp shown in the illustration, and connect the engine wire harness.

    Torque:
    Bolt A:
    11 N*m{ 112 kgf*cm , 8.1 ft.*lbf }
    Bolt B:
    13 N*m{ 131 kgf*cm , 9.5 ft.*lbf }

  1. G036390
    Connect the common rail connector.

  1. Install the wire harness with the screw grommet and the nut.

    Torque:
    1.6 N*m{ 16 kgf*cm , 14 in.*lbf }

  1. G036389
    Connect the VSV connector and wire harness clamp shown in the illustration.

  1. A125682
    Connect the wire harness clamp shown in the illustration.

  1. A125690
    Connect the supply pump connector.

  1. G036386
    Connect the injector connector.


17. INSTALL WATER PUMP ASSEMBLY

  1. A099105
    Install a new gasket and the water pump with the 3 bolts and 2 nuts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }


18. INSTALL WATER PUMP PULLEY

  1. A099104E01
    Temporarily install the water pump pulley with the 4 bolts.

  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Tighten the 4 bolts to the specified torque.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }


19. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY

A125676E01
  1. Install the engine mounting insulator RH with the 7 bolts and nut.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf } for bolt A
    88 N*m{ 897 kgf*cm , 65 ft.*lbf } for bolt B
    52 N*m{ 530 kgf*cm , 38 ft.*lbf } for nut C
    20 N*m{ 199 kgf*cm , 14 ft.*lbf } for bolt D


20. INSTALL GENERATOR ASSEMBLY

A128376E01
  1. Provisionally install the generator with fixing bolt C.

  1. A128375E01
    Provisionally install the fan belt adjusting slider with fan belt adjusting slider fixing bolt A and nut B, then move the generator toward the cylinder block and tighten bolt B.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf } for Bolt B

  1. A128374
    Install the connector.

  1. Install terminal B with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.


21. INSTALL FAN AND GENERATOR V BELT
  1. Temporarily install the fan and generator V belt onto each pulley.

    NOTICE:
    1. Before installing the V belt, check each pulley for any kind of liquid and chips.
    1. Check that the ribs of the V belt are correctly fitted into the grooves of the pulleys.


22. ADJUST FAN AND GENERATOR V BELT

  1. A098655
    Insert a bar between the generator and the engine. Pull the bar toward the front of the vehicle and adjust the tension.

  1. A098654E01
    Tighten bolt A, then tighten bolt B.

    Torque:
    Bolt A:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }
    Bolt B:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }


23. INSPECT FAN AND GENERATOR V BELT

B000543
  1. Check the belt for wear, cracks and other signs of damage.
    If any defects are found, replace the V belt.

    HINT:
    Replace the drive belt if any of the following defects are found:
    1. The belt is worn out and the wire is exposed.
    2. The cracks reach the wire in more than one place.
    3. The belt has pieces missing from the ribs.

  1. B075171E01
    Check that the belt fits properly into the ribbed grooves.

    HINT:
    With your hand, confirm that the belt has not slipped out of the grooves on the bottom of the pulley.


24. INSTALL EXHAUST MANIFOLD

  1. A128802
    Install the exhaust manifold through a new gasket with the 5 nuts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. A128801
    Install exhaust manifold heat insulator No. 1 with the 2 bolts.

    Torque:
    6 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Install the manifold stay with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


25. INSTALL TURBO OIL OUTLET PIPE

G038745
  1. Install a new gasket onto the cylinder block.

  1. G038743
    Provisionally install the turbo oil outlet pipe with 2 new nuts.


26. INSTALL TURBO CHARGER SUB-ASSEMBLY

G038742
  1. Install a new gasket onto the turbocharger.

  1. A098290
    Install a new gasket onto the exhaust manifold.

  1. A098289
    Install the turbocharger with the 3 nuts.

    Torque:
    53 N*m{ 540 kgf*cm , 39 ft.*lbf }

  1. Connect the vacuum hose to the turbocharger.

  1. A098285E01
    Tighten 2 new nuts B.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Tighten 2 new nuts A.

    Torque:
    14 N*m{ 140 kgf*cm , 10 ft.*lbf }


27. INSTALL AIR HOSE NO.1

A126499E01
  1. Install the intercooler air hose with the 2 hose clamps.

    Torque:
    6.0 N*m{ 60 kgf*cm , 53 in.*lbf }

    Specification:
    Area
    Measurement
    a
    0 to 2 mm (0 to 0.079 in.)
    b
    2 to 5 mm (0.079 to 0.197 in.)

    NOTICE:
    1. Align the paint mark of the intercooler air hose with the location mark of the turbocharger.
    2. Align the paint mark of the intercooler air hose with the location mark of air tube No. 1.
    3. Make sure that the hose clamp is at the correct angle when installing.


28. INSTALL TURBO OIL INLET PIPE

A098287E01
  1. Install 4 new gaskets and the turbo oil inlet pipe with 2 union bolts A.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

  1. Tighten bolt B.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Install wire harness clamp C.


29. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

A098284
  1. Install a new gasket onto the turbocharger.

  1. A126329E01
    Temporarily install the exhaust manifold converter with 3 new nuts A.

  1. Provisionally install the manifold support bracket with the bolt B.

  1. Tighten 3 nuts A.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  1. Tighten bolt B.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


30. INSTALL TURBO INSULATOR NO.1

A098282
  1. Install turbo insulator No. 1 with the 3 bolts.

    Torque:
    6.0 N*m{ 60 kgf*cm , 53 in.*lbf }

  1. A118858E01
    For LHD:

    1. Install the 2 bolts and brake booster vacuum pipe.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

  1. A118857E01
    For RHD:

    1. Install the bolt and brake booster vacuum pipe.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }


31. INSTALL EXHAUST PIPE ASSEMBLY FRONT

A077857
  1. Check the free length.

    1. Using vernier calipers, measure the free length of the compression spring.

      Minimum length:
      40.5mm (1.594 in.)

  1. Using a wooden block and plastic-hammer, tap in a new gasket until it is flush with the exhaust manifold converter.

    NOTICE:
    1. Make sure that the gasket is in the correct direction when installing it.
    2. Do not reuse a removed gasket.
    3. Never push the gasket into the exhaust manifold converter by installing the exhaust pipe front onto the exhaust manifold converter.

  1. A126322E01
    Install the exhaust pipe front onto the 3 exhaust pipe supports.

  1. Install a new gasket onto the exhaust pipe front.

  1. Install a new clamp with the bolt as shown in the illustration.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

    NOTICE:
    1. Do not reuse the removed gasket and clamp.
    2. Make sure that the pipe clamp is at the correct angle when installing it.

  1. Install the exhaust pipe front with the 2 compression springs and 2 bolts.

    Torque:
    43 N*m{ 440 kgf*cm , 32 ft.*lbf }


32. INSTALL INJECTION OR SUPPLY PUMP ASSEMBLY

NOTICE:
When installing, clean the seal surfaces of the fuel inlet pipe, supply pump and common rail.

  1. Apply a light coat of engine oil to a new O-ring.

  1. Install the O-ring onto the supply pump.

  1. Install the supply pump drive coupling onto the supply pump drive shaft.

  1. A125787
    Temporarily install the supply pump with the 3 bolts.

  1. Remove the vinyl bag and rubber band from the supply pump.

  1. Connect the 2 connectors.

  1. Connect the 3 fuel hoses.


33. INSTALL COMMON RAIL ASSEMBLY

A098485
  1. Install the common rail assembly

  1. Connect the fuel hose.

  1. Install the common rail with 2 bolts.

    Torque:
    26 N*m{ 265 kgf*cm , 19 in.*lbf }


34. INSTALL FUEL INLET PIPE SUB-ASSEMBLY

A125732E01

NOTICE:
  1. When replacing the supply pump, the fuel inlet pipe must also be replaced.
  2. Replace the fuel inlet pipe with a new one when the fuel inlet pipe has been removed and reinstalled more than 5 times.

  1. Temporarily install the fuel inlet pipe onto the supply pump and common rail.

    NOTICE:
    Install the pipe and union nut vertically, not at a tilt.

  1. Tighten the supply pump with the 3 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. A098463E01
    Using SST, tighten the fuel inlet pipe union nut of the fuel inlet pipe on the common rail side.
    SST
    09023-38401  

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf } with SST
    25 N*m{ 255 kgf*cm , 18 ft.*lbf } without SST

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. After the fuel inlet pipe has been reassembled, check that the used pipe has no deflection and is installed properly.
      If it has deflection or could not be installed properly, replace the used pipe with a new one.


35. INSTALL INJECTOR ASSEMBLY

A098455E01

NOTICE:
  1. When installing, clean the sealing surface of the injector, injection pipe and common rail.
  2. When replacing the injectors, the injection pipes must also be replaced.
  3. Replace the injection pipe with a new one when the injection pipe has been removed and reinstalled more than 5 times.
  4. Replace the injector with one with the same part number and install it onto the cylinder.

  1. Using a cloth and solvent, wipe away any carbon from the sealing surface of the injector and injector installation hole, as shown in the illustration.

    NOTICE:
    1. Do not damage the sealing surface.
    2. Do not touch the injector nozzle.

  1. Install 4 new nozzle seats onto the cylinder head.

  1. Install the injector onto the cylinder head.

    NOTICE:
    Fit the injectors into the seats.

  1. A099410E01
    Install the 4 nozzle holder clamp seats onto the cylinder head.

  1. Install the 4 nozzle holder clamps onto the injectors.

  1. Set the washer on the nozzle holder clamp, as shown illustration.

  1. Temporarily tighten the 4 nozzle holder clamp bolts.

  1. A125732E01
    Temporarily install the 4 injection pipes onto the injector and common rail.

    NOTICE:
    Install the pipe and union nut vertically, not at a tilt.

  1. Tighten the 4 nozzle holder clamp bolts.

    Torque:
    26 N*m{ 265 kgf*cm , 19 in.*lbf }

  1. A128766E01
    Using SST, tighten the injection pipe union nut of the injection pipe on the common rail side.
    SST
    09023-38401  

    Torque:
    With SST:
    23 N*m{ 235 kgf*cm , 17 in.*lbf }
    Without SST:
    25 N*m{ 255 kgf*cm , 18 in.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. After the injection pipe has been reassembled, check that the used pipe has no deflection and is installed properly, then replace the used pipe with a new one.

  1. A098458E01
    Using a spanner (13 mm), hold the injector steadily, and using SST, tighten the injection pipe union nut of the injection pipe on the injector side.
    SST
    09023-38401  

    Torque:
    With SST:
    23 N*m{ 235 kgf*cm , 17 in.*lbf }
    Without SST:
    25 N*m{ 255 kgf*cm , 18 in.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. After the injection pipe has been reassembled, check that the used pipe has no deflection and is installed properly, then replace the used pipe with a new one.

  1. G036562E01
    Connect the 4 injector connectors.

    NOTICE:
    Connect the black connector of the injector to injector No. 1 and No. 3, and brown connector to No. 2 and No. 4.


36. INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY

A068447

NOTICE:
  1. Never reuse the nozzle leakage pipe once it has been removed from the injectors and supply pump.
  2. Push the nozzle leakage pipe until it makes a click sound.

  1. Install 5 new retainer springs onto the injectors and supply pump.

  1. Push the new nozzle leakage pipe into each injector and supply pump.


37. INSTALL INJECTION PIPE SUB-ASSEMBLY NO. 1

A125732E01

CAUTION:
  1. When replacing the common rail, the injection pipes must also be replaced.
  2. Replace the injection pipe with a new one when the injection pipe has been removed and reinstalled more than 5 times.

  1. Temporarily install the 4 injection pipes onto the injector and common rail.

    NOTICE:
    Install the pipe and union nut vertically, not at a tilt.

  1. A128766E01
    Using SST, tighten the injection pipe union nut of the injection pipe on the common rail side.
    SST
    09023-38401  

    Torque:
    With SST:
    23 N*m{ 235 kgf*cm , 17 in.*lbf }
    Without SST:
    25 N*m{ 255 kgf*cm , 18 in.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. After the fuel inlet pipe has been reassembled, check that the used pipe has no deflection and is installed properly.
      If it has deflection or could not be installed properly, replace the used pipe with a new one.

  1. A098458E01
    Using a spanner (13 mm), hold the injector steady, and using SST, tighten the injection pipe union nut of the injection pipe with a new one.
    SST
    09023-38401  

    Torque:
    With SST:
    23 N*m{ 235 kgf*cm , 17 in.*lbf }
    Without SST:
    25 N*m{ 255 kgf*cm , 18 in.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. After the fuel inlet pipe has been reassembled, check that the used pipe has no deflection and is installed properly.
      If it has deflection or could not be installed properly, replace the used pipe with a new one.


38. INSTALL INJECTION PIPE SUB-ASSEMBLY NO. 2
  1. Perform the same procedure as for injection pipe No. 1.

    SST
    09023-38401  


39. INSTALL INJECTION PIPE SUB-ASSEMBLY NO. 3
  1. Perform the same procedure as for injection pipe No. 1.

    SST
    09023-38401  


40. INSTALL INJECTION PIPE SUB-ASSEMBLY NO. 4
  1. Perform the same procedure as for injection pipe No. 1.

    SST
    09023-38401  


41. INSTALL INJECTION PIPE CLAMP NO. 2

A128768E01
  1. Install injection pipe clamp No. 2 with the nut as shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


42. INSTALL INJECTION PIPE CLAMP NO. 1

A128769E01
  1. Install injection pipe clamp No. 1 with the 2 nuts as shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


43. INSTALL EGR PIPE CONNECTOR

A128827
  1. Install the EGR pipe connector with the 3 bolts.


44. INSTALL INTAKE AIR CONNECTOR

G036729
  1. Install the intake air connector with the 3 bolts.

  1. Connect the vacuum hose shown in the illustration.


45. INSTALL DIESEL THROTTLE BODY ASSEMBLY

  1. A125665
    Install a new gasket and the diesel throttle body with the 4 bolts.

    Torque:
    20 N*m{ 205 kgf*cm , 15 in.*lbf }

  1. A098266
    Connect the throttle position sensor connector.

  1. Connect the throttle control motor connector.


46. INSTALL VACUUM REGULATING VALVE ASSEMBLY

  1. A125788
    Install the vacuum regulating valve with the 3 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 in.*lbf }

  1. Connect the vacuum regulating valve connector and 2 vacuum hoses.


47. INSTALL EGR VALVE ASSEMBLY

  1. A125675
    Install a new gaskets.

  1. Install the EGR valve assembly with the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the EGR valve connector and hose.


48. INSTALL EGR COOLER PIPE SUB-ASSEMBLY

  1. A125674E01
    Install 2 new gaskets.

  1. Temporarily install the EGR cooler assembly with the bolt and 4 nuts, in the order described below.

    1. Tighten bolt B.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    2. Tighten the 2 A nuts.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    3. Tighten the 2 C nuts.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 water by-pass hoses.


49. INSTALL GLOW PLUG ASSEMBLY

A125733
  1. Clean the glow plug installation holes in the cylinder head.

  1. Using a 10 mm deep socket wrench , install the 4 glow plugs.

    Torque:
    :
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }


50. INSTALL GLOW PLUG NO. 1 CONNECTOR

A098272
  1. Install glow plug connector No. 1 with the 4 nuts.

    Torque:
    1.6 N*m{ 15 kgf*cm , 14 in.*lbf }

  1. Connect the glow terminal with the nut.

    Torque:
    3.8 N*m{ 40 kgf*cm , 34 in.*lbf }

    NOTICE:
    Install the glow terminal in the correct direction.

  1. A098269
    Install the 5 screw grommets.

    NOTICE:
    Push the screw grommet into the threaded portion of the glow plug by hand, and then turn it clockwise.


51. INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH HOSE

A126500E01
  1. Align the matchmarks of air cleaner hose No. 1 and turbocharger, and connect air cleaner hose No. 1 to the turbocharger and fasten air cleaner hose clamp No. 1.

    NOTICE:
    Make sure that the hose clamp is at the correct angle when installing it.

  1. A098276E01
    Connect the ventilation hose to the cylinder head cover.

    NOTICE:
    Make sure that the hose clamp is at the correct angle when installing it.

  1. Install the air cleaner cap onto the air cleaner case, then hang the 2 hook clamps.

  1. A118837
    Fit the wire harness into the air cleaner cap.

  1. Engage the 2 wire harness clamps.

  1. Connect the mass air flow meter connector.


52. INSTALL COWL TOP PANEL OUTER

A126332
  1. Install the cowl top panel outer with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Install the wire harness.


53. INSTALL COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2

A118801E01
  1. Engage the claws, and install cowl top register duct No. 2.


54. INSTALL FRONT WIPER MOTOR ASSEMBLY WITH LINK

E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


55. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.


56. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E113854
  1. Connect the washer hose.

  1. E113852
    Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.

  1. E117641
    Engage the 2 hooks and install cowl top ventilator louver center No. 1.


57. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.


58. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.


59. INSTALL HOOD TO COWL TOP SEAL

E113851
  1. Engage the 7 clips and install the hood to cowl top seal.


60. INSTALL FRONT WIPER ARM AND BLADE SUB-ASSEMBLY LH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113862E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


61. INSTALL FRONT WIPER ARM AND BLADE SUB-ASSEMBLY RH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113863E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


62. INSTALL FRONT WIPER ARM HEAD CAP

E113849
  1. Engage the claw and install the 2 front wiper arm head caps.


63. INSTALL BATTERY TRAY

64. INSTALL BATTERY

65. ADD ENGINE OIL
  1. Fill the engine oil with fresh engine oil.

    Capacity:
    Item
    Capacity
    Drain and refill with oil filter change
    4.3 liters (4.5 US qts, 3.8 lmp. qts)
    Drain and refill without oil filter change
    3.8 liters (4.0 US qts, 3.3 lmp. qts)
    Dry fill
    4.8 liters (5.1 US qts, 4.2 lmp. qts)


66. ADD ENGINE COOLANT

A128306E01
  1. Remove air bleed valve A.

  1. A128305
    Fill the cooling system with coolant up to line B.

    Capacity:
    4.7 liters (5.0 US qts, 4.1 lmp. qts)

    HINT:
    1. Use of improper coolant may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. A128306E01
    Tighten air bleed valve A.

  1. Install the radiator cap.

  1. Warm up the engine.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

  1. Run the engine at 3,000 rpm for 5 seconds and idling for 45 seconds alternately.

  1. Do the above operation for 7 minutes or more.

  1. After the engine cools down, check that the coolant level is between LOW and FULL lines.


67. INSPECT ENGINE OIL LEVEL
  1. Warm up the engine. Then stop the engine, and wait 5 minutes.

  1. Check that the engine oil level is between the 2 marks on the oil level gage.
    If low, check for leakage and top up oil to the upper mark.

    NOTICE:
    Do not add engine oil to above the upper mark.


68. CHECK FOR ENGINE OIL LEAKAGE

69. CHECK FOR ENGINE COOLANT LEAKAGE

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. A128299
    Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump it to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.


70. CHECK FOR FUEL LEAKAGE

A127178E01
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test.

    HINT:
    1. Fuel pressure inside common rail pressurized to 135 MPa and engine speed increased to 2,000 rpm when ON selected.
    2. Above conditions preserved while test ON.


71. CHECK FOR EXHAUST GAS LEAKAGE

72. INSTALL ENGINE COVER SUB-ASSEMBLY NO. 1

A125743
  1. Engage the 4 pins and install engine cover No. 1.


73. INSTALL ENGINE UNDER COVER
  1. Provisionally install the engine under cover with the 5 bolts, 4 screws and 2 clips.

  1. Tighten the 4 screws.

  1. Tighten the 5 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


74. INSTALL FRONT WHEEL RH

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }

← REASSEMBLY (from Nov 2005)REPAIR (from Nov 2005) →