2005-2008 Yaris · Service Manual BODY ELECTRICAL

Taillight Circuit

Circuit diagnosis · Vehicles built Aug 2005 – Oct 2006

Versions by build date: Aug 2005 – Oct 2006 from Nov 2006

DESCRIPTION

Vehicles equipped with the daytime running light system: When the light control switch, located on the headlight dimmer switch, is turned to the TAIL position, the taillight relay turns on to illuminate the front position lights, rear taillights and license plate light.
Vehicles without the daytime running light system: When the light control switch, located on the headlight dimmer switch, is turned to the TAIL position, the front position lights, rear taillights and license plate light illuminate.

WIRING DIAGRAM

B126442E02
B145265E01

INSPECTION PROCEDURE


1. CHECK WHETHER LIGHTS ILLUMINATE
  1. Check whether the following lights illuminate: Front position lights, Rear taillights and License plate light.

    Result:
    Illumination Condition
    Proceed To
    All lights illuminate
    A
    No lights illuminate
    B
    Front position lights do not illuminate
    C
    Rear taillights do not illuminate
    D
    License plate light does not illuminate
    E



B
Go to step 2

C
Go to step 11

D
Go to step 13

E
Go to step 15
A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2. CHECK VEHICLE SPECIFICATIONS
  1. Check whether the vehicle is equipped with the daytime running light system.

    Result:
    Daytime running light system
    Proceed To
    Yes
    A
    No
    B



B
Go to step 8
A


3. INSPECT FUSE (TAIL)
  1. Remove the TAIL fuse from the main body ECU.

  1. Measure the resistance.

    Standard resistance:
    Below 1 Ω

  1. Reconnect the TAIL fuse.



NG
REPLACE FUSE
OK


4. INSPECT MAIN BODY ECU
B129036E01
  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    4A-10 - Body ground
    Ignition switch on (IG)
    Headlight dimmer switch TAIL
    10 to 14 V
    4A-29 - Body ground
    Ignition switch on (IG)
    Headlight dimmer switch TAIL
    10 to 14 V
    4B-33 - Body ground
    Ignition switch on (IG)
    Headlight dimmer switch TAIL
    10 to 14 V
    4G-1 - Body ground
    Always
    10 to 14 V
    4S-9 - Body ground
    Always
    10 to 14 V



NG
REPLACE MAIN BODY ECU
OK


5. INSPECT HEADLIGHT DIMMER SWITCH

  1. B126089E08
    Remove the headlight dimmer switch.

  1. Inspect the light control switch.

  1. Measure the resistance.

    Standard resistance:
    LHD and RHD for Europe:
    Tester Connection
    Condition
    Specified Condition
    10 (T1) - 13 (B1)
    TAIL
    Below 1 Ω
    10 (T1) - 13 (B1)
    OFF
    10 kΩ or higher
    10 (T1) - 13 (B1)
    HEAD
    Below 1 Ω
    10 (T1) - 13 (B1)
    OFF
    10 kΩ or higher
    11 (ED) - 12 (RF)
    HEAD
    Below 1 Ω
    11 (ED) - 12 (RF)
    OFF
    10 kΩ or higher
    RHD except Europe:
    Tester Connection
    Condition
    Specified Condition
    5 (B1) - 8 (T1)
    TAIL
    Below 1 Ω
    5 (B1) - 8 (T1)
    OFF
    10 kΩ or higher
    5 (B1) - 8 (T1)
    HEAD
    Below 1 Ω
    5 (B1) - 8 (T1)
    OFF
    10 kΩ or higher
    6 (RF) - 7 (ED)
    HEAD
    Below 1 Ω
    6 (RF) - 7 (ED)
    OFF
    10 kΩ or higher

  1. Reinstall the headlight dimmer switch.



NG
REPLACE HEADLIGHT DIMMER SWITCH
OK


6. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - RUNNING LIGHT RELAY ASSEMBLY)

  1. B126213E03
    Disconnect the D50 running light relay assembly connector.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D50-3 (TAIL) - Body ground
    Always
    10 to 14 V

  1. Reconnect the running light relay assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (RUNNING LIGHT RELAY ASSEMBLY - HEADLIGHT DIMMER SWITCH)

  1. B129035E01
    Disconnect the D50 running light relay assembly connector.

  1. Disconnect the D4 headlight dimmer switch connector.

  1. Measure the resistance.

    Standard resistance:
    LHD and RHD for Europe:
    Tester Connection
    Specified Condition
    D50-2 (T) - D4-13 (B1)
    Below 1 Ω
    D50-2 (T) or D4-13 (B1) - Body ground
    10 kΩ or higher
    RHD except Europe:
    Tester Connection
    Specified Condition
    D50-2 (T) - D4-5 (B1)
    Below 1 Ω
    D50-2 (T) or D4-5 (B1) - Body ground
    10 kΩ or higher

  1. Reconnect the running light relay assembly connector.

  1. Reconnect the headlight dimmer switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT DIMMER SWITCH - BODY GROUND)

8. INSPECT FUSE
  1. Remove the TAIL fuse from the main body ECU.

  1. Measure the resistance.

    Standard resistance:
    Below 1 Ω

  1. Reconnect the TAIL fuse.



NG
REPLACE FUSE
OK


9. INSPECT HEADLIGHT DIMMER SWITCH

  1. B126089E08
    Remove the headlight dimmer switch.

  1. Inspect the light control switch.

  1. Measure the resistance.

    Standard resistance:
    LHD and RHD for Europe:
    Tester Connection
    Condition
    Specified Condition
    10 (T1) - 13 (B1)
    TAIL
    Below 1 Ω
    10 (T1) - 13 (B1)
    OFF
    10 kΩ or higher
    10 (T1) - 13 (B1)
    HEAD
    Below 1 Ω
    10 (T1) - 13 (B1)
    OFF
    10 kΩ or higher
    11 (ED) - 12 (RF)
    HEAD
    Below 1 Ω
    11 (ED) - 12 (RF)
    OFF
    10 kΩ or higher
    RHD except Europe:
    Tester Connection
    Condition
    Specified Condition
    5 (B1) - 8 (T1)
    TAIL
    Below 1 Ω
    5 (B1) - 8 (T1)
    OFF
    10 kΩ or higher
    5 (B1) - 8 (T1)
    HEAD
    Below 1 Ω
    5 (B1) - 8 (T1)
    OFF
    10 kΩ or higher
    6 (RF) - 7 (ED)
    HEAD
    Below 1 Ω
    6 (RF) - 7 (ED)
    OFF
    10 kΩ or higher

  1. Reinstall the headlight dimmer switch.



NG
REPLACE HEADLIGHT DIMMER SWITCH
OK


10. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HEADLIGHT DIMMER SWITCH)

  1. B126090E06
    Disconnect the D4 headlight dimmer switch.

  1. Measure the voltage.

    Standard voltage:
    LHD and RHD for Europe:
    Tester Connection
    Specified Condition
    D4-13 (B1) - Body Ground
    10 to 14 V
    RHD except Europe:
    Tester Connection
    Specified Condition
    D4-5 (B1) - Body Ground
    10 to 14 V

  1. Reconnect the headlight dimmer switch.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT DIMMER SWITCH - MAIN BODY ECU)

11. INSPECT BULB (FRONT POSITION LIGHT BULB)

  1. Hatchback:

    1. B141827E01
      Remove the front position light.

    2. Apply battery voltage to the terminals and check that the front position light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 1
      Negative battery - Terminal 2
      Front position light illuminates

    3. Reinstall the front position light.

  1. Sedan:

    1. B144226E05
      Remove the front position light.

    2. Apply battery voltage to the terminals and check that the front position light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 3
      Negative battery - Terminal 2
      Front position light illuminates

    3. Reinstall the front position light.



NG
REPLACE BULB
OK


12. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POSITION LIGHT)

  1. Hatchback:

    1. B135318E02
      Disconnect the B3 and B7 front position light connectors.

    2. Disconnect the 4B main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4B-33 - B3-1
      Below 1 Ω
      4B-33 - B7-1
      Below 1 Ω
      4B-33 or B3-1 - Body ground
      10 kΩ or higher
      4B-33 or B7-1 - Body ground
      10 kΩ or higher

    4. Reconnect the front position light connectors.

    5. Reconnect the main body ECU connector.

  1. Sedan:

    1. B144227E05
      Disconnect the B16 and B17 front position light connectors.

    2. Disconnect the 4B main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4B-33 - B16-3
      Below 1 Ω
      4B-33 - B17-3
      Below 1 Ω
      4B-33 or B16-3 - Body ground
      10 kΩ or higher
      4B-33 or B17-3 - Body ground
      10 kΩ or higher

    4. Reconnect the front position light connectors.

    5. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT POSITION LIGHT - BODY GROUND)

13. INSPECT BULB (REAR TAILLIGHT BULB)

  1. Hatchback:

    1. B129860E03
      Remove the rear combination light assembly.

    2. Apply battery voltage to the terminals and check that the rear taillight illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 4
      Negative battery - Terminal 6
      Rear taillight illuminates

    3. Reinstall the rear combination light assembly.

  1. Sedan:

    1. B141033E01
      Remove the rear combination light assembly.

    2. Apply battery voltage to the terminals and check that the rear taillight illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 4
      Negative battery - Terminal 6
      Rear taillight illuminates

    3. Reinstall the rear combination light assembly.



NG
REPLACE BULB
OK


14. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REAR TAILLIGHT)

  1. Hatchback:

    1. B131873E05
      Disconnect the J3 and J4 rear combination light assembly connectors.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4A-10 - J3-4
      Below 1 Ω
      4A-29 - J4-4
      Below 1 Ω
      4A-10 or J3-4 - Body ground
      10 kΩ or higher
      4A-29 or J4-4 - Body ground
      10 kΩ or higher

    4. Reconnect the rear combination light assembly connectors.

    5. Reconnect the main body ECU connector.

  1. Sedan:

    1. B141726E07
      Disconnect the J41 and J42 rear combination light assembly connectors.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4A-10 - J41-4
      Below 1 Ω
      4A-29 - J42-4
      Below 1 Ω
      4A-10 or J41-4 - Body ground
      10 kΩ or higher
      4A-29 or J42-4 - Body ground
      10 kΩ or higher

    4. Reconnect the rear combination light assembly connectors.

    5. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR TAILLIGHT - BODY GROUND)

15. INSPECT BULB (LICENSE PLATE LIGHT BULB)

  1. Hatchback (G. C. C. Countries):

    1. B141830E01
      Remove the license plate light assembly.

    2. Apply battery voltage to the terminals and check that the license plate light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 2
      Negative battery - Terminal 1
      License plate light illuminates

    3. Reinstall the license plate light assembly.

  1. Hatchback (Except G. C. C. Countries):

    1. B141829E01
      Remove the license plate light assembly.

    2. Apply battery voltage to the terminals and check that the license plate light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 2
      Negative battery - Terminal 1
      License plate light illuminates

    3. Reinstall the license plate light assembly.

  1. Sedan:

    1. B141842E01
      Remove the license plate light assembly.

    2. Apply battery voltage to the terminals and check that the license plate light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 2
      Negative battery - Terminal 1
      License plate light illuminates

    3. Reinstall the license plate light assembly.



NG
REPLACE BULB
OK


16. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - LICENSE PLATE LIGHT ASSEMBLY)

  1. Hatchback (G. C. C. Countries):

    1. B141839E01
      Disconnect the L1 license plate light assembly connector.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4A-29 - L1-2
      Below 1 Ω
      4A-29 or L1-2 - Body ground
      10 kΩ or higher

    4. Reconnect the license plate light assembly connector.

    5. Reconnect the main body ECU connector.

  1. Hatchback (Except G. C. C. Countries):

    1. B141840E01
      Disconnect the J38 license plate light assembly connector.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4A-29 - J38-2
      Below 1 Ω
      4A-29 or J38-2 - Body ground
      10 kΩ or higher

    4. Reconnect the license plate light assembly connector.

    5. Reconnect the main body ECU connector.

  1. Sedan:

    1. B141841E01
      Disconnect the J43 and J44 license plate light assembly connectors.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4A-29 - J43-2
      Below 1 Ω
      4A-29 - J44-2
      Below 1 Ω
      4A-29 or J43-2 - Body ground
      10 kΩ or higher
      4A-29 or J44-2 - Body ground
      10 kΩ or higher

    4. Reconnect the license plate light assembly connectors.

    5. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (LICENSE PLATE LIGHT ASSEMBLY - BODY GROUND)


← Hazard Warning Switch Circuit (from Aug 2005)Taillight Circuit (from Nov 2006) →