2005-2008 Yaris · Service Manual ENGINE

P0236 Turbocharger / Supercharger Boost Sensor "A" Circuit Range / Performance

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

The manifold absolute pressure sensor detects the intake manifold pressure. The ECM determines the basic injection duration and injection advance timing based on the voltage output from the manifold absolute pressure sensor.
DTC No.
DTC Detection Conditions
Trouble Areas
P0236
The manifold absolute pressure sensor output differs from atmospheric pressure sensor output by more than threshold for 2 seconds or more
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  1. Open or short in manifold absolute pressure sensor circuit
  2. Manifold absolute pressure sensor
  3. ECM
P0237
P0238
Open or short in manifold absolute pressure sensor circuit for 2 seconds or more
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)

HINT:
  1. DTC P0236 is set while idling for 10 seconds or more.
  2. DTC P0237 is set when the ignition switch is in the on (IG) position.
  3. DTC P0238 is set when the ignition switch is in the on (IG) position.
  4. When DTCs P0236, P0237 and/or P0238 are set, check the pressure by selecting the following menu items: Powertrain / Engine and ECT / Data List / PIM.


Reference:
Intake Manifold Pressure (kPa)
Malfunction
Approximately 0
  1. Short in PIM circuit
250 or more
  1. Open or short in VC circuit
  2. Open in PIM circuit
  3. Open in E2 circuit


WIRING DIAGRAM

A115986E02

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (MANIFOLD ABSOLUTE PRESSURE)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / PIM.

  1. Read the values displayed on the tester.

    OK:
    Same value as the actual atmospheric pressure.



OK
Go to step 3
NG


2. CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

  1. A122603E01
    Disconnect the A33 manifold absolute pressure sensor connector.

  1. Disconnect the C50 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    PIM (A33-2) - PIM (C50-38)
    Below 1 Ω
    VC (A33-3) - VPIM (C50-30)
    E (A33-1) - EPIM (C50-17)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    PIM (A33-2) or PIM (C50-38) - Body ground
    10 kΩ higher
    VC (A33-3) or VPIM (C50-30) - Body ground
    E (A33-1) or EPIM (C50-17) - Body ground

  1. Reconnect the manifold absolute pressure sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NEXT


4. CHECK WHETHER DTC OUTPUT RECURS (DTC P0236, P0237 AND/OR P0238)
  1. Connect an intelligent tester to the DLC3.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    No output
    A
    DTC P0236, P0237, P0237 and/or P0238
    B



B
REPLACE ECM
A

END


← P0234 Turbocharger / Supercharger Overboost Condition (+ P0299) (from Nov 2005)P0252 Injection Pump Fuel Metering Control "A" Range / Performance (Cam / Rotor / Injector) (+ P1228) (from Nov 2005) →