2005-2008 Yaris · Service Manual ENGINE

P0252 Injection Pump Fuel Metering Control "A" Range / Performance (Cam / Rotor / Injector)

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

DTC No.
DTC Detection Conditions
Trouble Areas
P0252
  1. Open or short in fuel metering unit circuit for more than 0.5 seconds (DTC P1228 set simultaneously)
    (The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  2. ECM internal error (DTC P1228 not set)
    (The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  1. Open or short in fuel metering unit circuit
  2. Fuel metering unit
  3. ECM
P1228
Open or short in fuel metering unit circuit for more than 0.5 seconds
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)

HINT:
  1. These DTCs are set when the engine idles for approximately 60 seconds.
  2. When DTC P0252 and/or P1228 is set, check the internal fuel pressure of the common rail by selecting the following menu items on the intelligent tester: Powertrain / Engine and ECT / Data List / Common Rail Pressure.


Engine Speed
Fuel Pressure (MPa)
Idling
Approximately 25 to 36
2,000 rpm (No engine load)
Approximately 27 to 46
3,000 rpm (No engine load)
Approximately 34 to 69


WIRING DIAGRAM

A122655E02

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. READ OUTPUT DTCS (DTC P0252 AND/OR P1228)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P1228, or P0252 and P1228
    A
    Only P0252
    B



B
REPLACE ECM
A


2. INSPECT SUPPLY PUMP ASSEMBLY (FUEL METERING UNIT)

  1. A122675E01
    Disconnect the C54 fuel metering unit connector.

  1. Measure the resistance between the terminals of the fuel metering unit valve.

    Standard resistance:
    2.60 to 3.15 Ω at 20°C (68°F)

  1. Reconnect the fuel metering unit connector.



NG
REPLACE SUPPLY PUMP ASSEMBLY (FUEL METERING UNIT)
OK


3. CHECK FUSE (ECD2 FUSE)

  1. A107902E03
    Remove the ECD2 fuse from the engine room relay block.

  1. Check the ECD2 fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the ECD2 fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


4. CHECK HARNESS AND CONNECTOR (ECD RELAY - FUEL METERING UNIT - ECM)

  1. A122651E02
    Disconnect the C54 fuel metering unit connector.

  1. Disconnect the C50 ECM connector.

  1. Remove the integration relay from the engine room relay block.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    (C54-1) - Integration relay (1A-8)
    Below 1 Ω
    PCV (C50-12) - (C54-2)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    (C54-1) or Integration relay (1A-8) - Body ground
    10 kΩ or higher
    PCV (C50-12) or (C54-2) - Body ground

  1. Reinstall the integration relay.

  1. Reconnect the ECM connector.

  1. Reconnect the fuel metering unit connector.



OK
REPLACE ECM
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR


← P0236 Turbocharger / Supercharger Boost Sensor "A" Circuit Range / Performance (+ P0237, P0238) (from Nov 2005)P0263 Cylinder 1 Contribution / Balance (+ P0266, P0269, P0272, P0300) (from Nov 2005) →