2005-2008 Yaris · Service Manual ENGINE

P0234 Turbocharger / Supercharger Overboost Condition

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

Refer to DTC P0045 (Click here).
DTC No.
DTC Detection Conditions
Trouble Areas
P0234
Actual turbocharger pressure higher than target pressure for about 10 seconds
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  1. VRV (Vacuum Regulating Valve)
  2. Open or short in VRV circuit
  3. Turbocharger assembly
  4. EGR valve assembly
  5. Intake shutter
  6. Manifold absolute pressure sensor
  7. Vacuum hose
  8. ECM
P0299
Actual turbocharger pressure lower than target pressure for about 10 seconds
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)

HINT:
These DTCs are set while steady speed driving with a highly engine load (at an engine speed of 3,000 rpm or more).


WIRING DIAGRAM

Refer to DTC P0045 for VRV circuit (Click here).
Refer to DTC P0400 for EGR valve circuit (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0234 AND/OR P0299)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0234 and/or P0299
    A
    P0234 and/or P0299 and other DTCs
    B



B
GO TO DTC CHART
A


2. CHECK VACUUM HOSES CONNECTIONS

HINT:
Check the vacuum hose connection of the turbocharger system.

OK:
The vacuum hoses are appropriately connected to each other.



NG
REPAIR OR REPLACE VACUUM HOSES
OK


3. CHECK VACUUM HOSES (CHECK VACUUM BETWEEN TURBOCHARGER - VRV FOR TURBO CHARGER)
  1. Using a three-way connector, connect a vacuum gauge to the hoses between the VRV (Vacuum Regulating Valve) and turbocharger.

  1. Warm up the engine coolant temperature to more than 75°C (167°F).

  1. Check the vacuum at the engine speed of idling.

    Result:
    Vacuum
    Proceed To
    0 kPa (0 mmHg, 0 in.Hg) to 50 kPa (375 mmHg, 14.8 in.Hg)
    A
    Above 50 kPa (375 mmHg, 14.8 in.Hg)
    B



B
Go to step 7
A


4. INSPECT VACUUM REGULATING VALVE ASSEMBLY (OPERATION)

  1. A126326E01
    Remove the vacuum regulating valve (Click here).

  1. Apply 4 dry batteries of 1.5 V in series.

  1. Check that the needle does not move when a vacuum is applied to the vacuum inlet port.

    OK:
    The VRV operates normally.

  1. Reinstall the vacuum regulating valve (Click here).



NG
REPLACE VACUUM REGULATING VALVE ASSEMBLY
OK


5. INSPECT VACUUM REGULATING VALVE ASSEMBLY (RESISTANCE)

  1. A122640E01
    Remove the vacuum regulating valve (Click here).

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connections
    Specified Conditions
    1 - 2
    11 to 13 Ω at 20°C (68°F)

  1. A122641E02
    Check the resistance between each terminal and the body.

    Standard resistance:
    Tester Connections
    Specified Conditions
    1 - Body
    1 MΩ or higher
    2 - Body

  1. Reinstall the vacuum regulating valve (Click here).



NG
REPLACE VACUUM REGULATING VALVE ASSEMBLY
OK


6. CHECK HARNESS AND CONNECTOR (VRV - ECM, VRV - ECD RELAY)

  1. A122604E02
    Disconnect the C55 VRV connector.

  1. Disconnect the C50 ECM connector.

  1. Remove the integration relay from the engine room relay block.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    VN (C50-33) - (C55-2)
    Below 1 Ω
    Integration relay (1A-8) - (C55-1)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VN (C50-33) or (C55-2) - Body ground
    10 kΩ or higher
    Integration relay (1A-8) or (C55-1) - Body ground

  1. Reconnect the VRV connector.

  1. Reconnect the ECM connector.

  1. Reinstall the integration relay.



NG
Go to step 17
OK


7. READ VALUE USING INTELLIGENT TESTER (MANIFOLD ABSOLUTE PRESSURE)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / PIM.

  1. Read the values displayed on the tester.

    OK:
    Same value as the actual atmospheric pressure.



NG
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
OK


8. CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

  1. A122603E01
    Disconnect the A33 manifold absolute pressure sensor connector.

  1. Disconnect the C50 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    PIM (A33-2) - PIM (C50-38)
    Below 1 Ω
    VC (A33-3) - VPIM (C50-30)
    E (A33-1) - EPIM (C50-17)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    PIM (A33-2) or PIM (C50-38) - Body ground
    10 kΩ higher
    VC (A33-3) or VPIM (C50-30) - Body ground
    E (A33-1) or EPIM (C50-17) - Body ground

  1. Reconnect the manifold absolute pressure sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT DIESEL THROTTLE BODY ASSEMBLY
A170630E01

NOTICE:
Perform this inspection with the engine off.

  1. Turn the ignition switch off.

  1. Remove the air cleaner hose.

  1. Visually confirm the position of the throttle valve in the diesel throttle body assembly.

    OK:
    Partially open

    If the valve is fully open or fully closed, replace the diesel throttle body assembly.

  1. Turn the ignition switch on.

  1. Visually confirm the position of the throttle valve in the diesel throttle body assembly.

    OK:
    Fully open

    If the result is not OK, replace the diesel throttle body assembly.

  1. Visually confirm the motion of the throttle valve in the diesel throttle body assembly when the ignition switch is turned from ON to OFF.

    OK:
    Throttle valve should move from fully open to fully closed and then to partially open.

    If the result is not OK, replace the diesel throttle body assembly.



NG
REPLACE DIESEL THROTTLE BODY ASSEMBLY
OK


10. CHECK HARNESS AND CONNECTOR (INTAKE SHUTTER - ECM)

  1. A122609E01
    Disconnect the C58 intake shutter connector.

  1. Disconnect the C50 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    VVLU (C50-27) - VC (C58-1)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VVLU (C50-27) or VC (C58-1) - Body ground
    10 kΩ or higher

  1. Reconnect the intake shutter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. INSPECT EGR VALVE ASSEMBLY

  1. A122610E02
    Disconnect C52 EGR valve connector.

  1. Measure the resistance between the terminals of the EGR valve connector.

    Standard resistance:
    Tester Connections
    Specified Conditions
    +B2 (5) - EGR1 (4)
    18.2 to 21.0 Ω at 20°C (68°F)
    +B2 (5) - EGR3 (6)
    +B1 (2) - EGR2 (1)
    +B1 (2) - EGR4 (3)



NG
REPLACE EGR VALVE ASSEMBLY
OK


12. CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)

  1. A122611E02
    Disconnect the C52 EGR valve connector.

  1. Disconnect the A49 EGR valve connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    EGR1 (A49-12) - EGR1 (C52-4)
    Below 1 Ω
    EGR2 (A49-11) - EGR2 (C52-1)
    EGR3 (A49-31) - EGR3 (C52-6)
    EGR4 (A49-30) - EGR4 (C52-3)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    EGR1 (A49-12) or EGR1 (C52-4) - Body ground
    10 kΩ higher
    EGR2 (A49-11) or EGR2 (C52-1) - Body ground
    EGR3 (A49-31) or EGR3 (C52-6) - Body ground
    EGR4 (A49-30) or EGR4 (C52-3) - Body ground

  1. Reconnect the EGR valve connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13. INSPECT ECM (EGR VOLTAGE)

  1. A122612E01
    Disconnect the C52 EGR valve connector.

  1. Inspect the ECM using an oscilloscope.

  1. While repeating quick engine RPM accelerations, check the waveform between the terminals of the C52 EGR valve connector.

    Standard:
    Tester Connections
    Specified Conditions
    EGR1 (C52-4) - Body ground
    Correct waveform shown
    EGR2 (C52-1) - Body ground
    EGR3 (C52-6) - Body ground
    EGR4 (C52-3) - Body ground

  1. Reconnect the EGR valve connector.



NG
REPLACE ECM
OK


14. CHECK FOR DEPOSIT (EGR VALVE ASSEMBLY)

OK:
No deposit



NG
REMOVE FOREIGN OBJECT AND CLEAN EGR VALVE
OK


15. CHECK FOR DEPOSIT (EGR PASSAGE)

OK:
No deposit



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
OK


16. CHECK FOR EXHAUST GAS LEAK

OK:
No leakage



NG
CHECK EXHAUST GAS LEAKAGE POINT
OK

REPLACE EGR VALVE ASSEMBLY

17. CHECK FUSE (ECD2 FUSE)

  1. A107902E03
    Remove the ECD2 fuse from the engine room relay block.

  1. Check the ECD2 fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the ECD2 fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK

CHECK ECM POWER SOURCE CIRCUIT


← P0201 Injector Circuit / Open - (Cylinder 1) (+ P0202, P0203, P0204, P2146) (from Nov 2005)P0236 Turbocharger / Supercharger Boost Sensor "A" Circuit Range / Performance (+ P0237, P0238) (from Nov 2005) →