2005-2008 Yaris · Service Manual ENGINE

P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

CAUTION / NOTICE / HINT

HINT:
  1. These DTCs related to the intake shutter (throttle valve) position sensor.
  2. This electronic throttle system does not use a throttle cable.
  3. This intake shutter position sensor is a non-contact type.


DESCRIPTION

The intake shutter (throttle valve) position sensor is mounted on the intake shutter body and it detects the opening angle of the intake shutter. This sensor is electronically controlled and uses Hall-effect elements.
A092196E01
DTC No.
DTC Detection Conditions
Trouble Areas
P0122
Intake shutter position sensor output (VLU) is less than 0.2 V
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  1. Intake shutter position sensor
  2. Open or short in VLU circuit
  3. Open in VC circuit
  4. ECM
P0123
Intake shutter position sensor output (VLU) is more than 4.8 V
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  1. Intake shutter position sensor
  2. Open in E2 circuit
  3. VC and VLU circuits are short-circuited
  4. ECM

HINT:
These DTCs are set when the ignition switch is in the on (IG) position.


WIRING DIAGRAM

A122647E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (INTAKE SHUTTER (THROTTLE VALVE) POSITION SENSOR - ECM)

  1. A122649E01
    Disconnect the C58 intake shutter position sensor connector.

  1. Disconnect the C50 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    VVLU (C50-27) - VC (C58-1)
    Below 1 Ω
    VLU (C50-35) - VTA (C58-3)
    EVLU (C50-14) - E2 (C58-2)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VVLU (C50-27) or VC (C58-1) - Body ground
    10 kΩ or higher
    VLU (C50-35) or VTA (C58-3) - Body ground
    EVLU (C50-14) or E2 (C58-2) - Body ground

  1. Reconnect the intake shutter position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT ECM (VC VOLTAGE)

  1. A122648E01
    Disconnect the C58 intake shutter position sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals of the C58 intake shutter position sensor connector.

    Standard:
    Tester Connections
    Specified Conditions
    VC (C58-1) - E2 (C58-2)
    4.5 to 5.5 V

  1. Reconnect the intake shutter position sensor connector.



NG
REPLACE ECM
OK


3. REPLACE INTAKE SHUTTER ASSEMBLY (THROTTLE VALVE)

NEXT


4. CHECK WHETHER DTC OUTPUT RECURS (DTC P0122 AND/OR P0123)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.

  1. Clear DTCs (Click here).

  1. Let the engine idle for 60 seconds, and repeat quick engine RPM accelerations (to 2,500 rpm) for 30 seconds.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0122 and/or P0123
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM


← P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem (+ P0487, P0488) (from Nov 2005)P0182 Fuel Temperature Sensor "A" Circuit Low Input (+ P0183) (from Nov 2005) →