2005-2008 Yaris · Service Manual ENGINE

P1520 Stop Light Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

In this system, the signal transmitted from the stop light switch is used to determine whether or not the brake system is normal.
The stop light switch has a duplex system (signals STP and ST1) to detect abnormalities. When the signals of depressing and releasing the brake pedal are detected simultaneously, the ECM interprets this as a malfunction of the stop light switch.

HINT:
Normal condition is shown in the table below.
Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1
ON
ON
OFF
DTC No.
DTC Detection Conditions
Trouble Areas
P1520
Conditions (a), (b) and (c) continue for 5.0 seconds or more:
(a) Ignition switch on (IG)
(b) Brake pedal depressed
(c) STP signal OFF when ST1 signal OFF
(The MIL is illuminated and a DTC is set when the same malfunction is detected on 2 consecutive trips*
*: One trip is counted when the ignition switch is turned from off to on (IG) and back to off)
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

HINT:
DTC P1520 is set when the ignition switch is in the on (IG) position.


WIRING DIAGRAM

A122590E02

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.
  2. STP signal conditions can be checked using an intelligent tester.
    1. Connect an intelligent tester to the DLC3.
    2. Turn the ignition switch on (IG) and turn the tester on.
    3. Select the following menu items: Powertrain / Engine and ECT / Data List / Stop Light Switch.
    4. Check the STP signal when the brake pedal is depressed and released.
      Brake Pedal Operations
      Specified Conditions
      Depressed
      STP signal ON
      Released
      STP signal OFF


1. CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)

  1. A115660E03
    Disconnect the A13 stop light switch connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals ST1 and STP of the A13 stop light switch connector and body ground.

    Standard voltage:
    9 to 14 V

  1. Reconnect the stop light switch connector.



NG
Go to step 4
OK


2. INSPECT STOP LIGHT SWITCH ASSEMBLY

  1. A115657E03
    Remove the stop light switch assembly.

  1. Check the resistance.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    1 - 2
    Switch pin released
    Below 1 Ω
    Switch pin pushed in
    10 kΩ or higher
    3 - 4
    Switch pin released
    10 kΩ or higher
    Switch pin pushed in
    Below 1 Ω

  1. Reinstall the stop light switch assembly.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


3. CHECK ECM (STP AND ST1 VOLTAGE)

  1. A122673E01
    Disconnect the A49 ECM connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals ST1 and STP of the A49 ECM connector and body ground.

    Standard voltage:
    Tester Connection
    Brake control Operations
    Specified Condition
    ST1 (A49-27) - Body ground
    Released
    9 to 14 V
    Depressed
    0 to 3 V
    STP (A49-8) - Body ground
    Released
    0 to 3 V
    Depressed
    9 to 14 V

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

4. INSPECT FUSE (STOP AND IGN FUSE)

  1. A107935E15
    Remove the STOP and IGN fuses from the main body ECU.

  1. Check the resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the STOP and IGN fuses.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR


← P1229 Fuel Pump System (+ P1272) (from Nov 2005)P1600 ECM BATT Malfunction (from Nov 2005) →