2005-2008 Yaris · Service Manual ENGINE

P1120 Accelerator Pedal Position Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Nov 2005

CAUTION / NOTICE / HINT

HINT:
  1. This is the repair procedure for the accelerator pedal position sensor.
  2. This electrical throttle system does not use a throttle cable.
  3. This accelerator pedal position sensor is a non-contact type.


DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and malfunctions of the accelerator position sensor.
In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal which indicates the actual accelerator pedal opening angle and is used for engine control, and the VPA2 is a signal which indicates the information about the opening angle and is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the throttle motor based on these signals.
A112620E01
DTC No.
DTC Detection Conditions
Trouble Areas
P1120
Condition (a) or (b) continues for 0.5 seconds or more:
  1. (a) VPA less than 0.2 V when accelerator pedal fully released, or VPA more than 4.8 V
    (The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  2. (b) VPA2 less than 0.5 V when accelerator pedal fully released, or VPA2 more than 4.8 V
    (The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  1. Open or short in accelerator pedal position sensor circuit
  2. Accelerator pedal position sensor
  3. ECM

HINT:
This DTC is set when the ignition switch is in the on (IG) position.

HINT:
When DTC P1120 is set, check the accelerator pedal position sensor output voltage by selecting the following menu items on the intelligent tester: Powertrain / Engine and ECT / Data List / Accel Position.


Reference:
Accelerator Pedal Position (Fully Closed)
Accelerator Pedal Position (Fully Open)
Trouble Areas
0 %
0 %
  1. Open in VCPA or VCP2 circuit
  2. Open or short in VPA or VPA2 circuit
Approximately 100 %
Approximately 100 %
  1. Open in EPA or EPA2 circuit

HINT:
Accelerator pedal positions are expressed as voltages.


WIRING DIAGRAM

A112573E01

INSPECTION PROCEDURE

Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1. READ VALUE USING INTELLIGENT TESTER (ACCEL POSITION)

  1. FI07052E07
    Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Accel Position.

  1. Read the values displayed on the tester.

    Standard:
    Accelerator Pedal Operations
    Specified Conditions
    Depressed
    100 %
    Released
    0 %



OK
REPLACE ECM
NG


2. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

  1. A129238E01
    Disconnect the A20 accelerator pedal position sensor connector.

  1. Disconnect the A49 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    VCPA (A49-34) - VCPA (A20-4)
    Below 1 Ω
    VPA (A49-15) - VPA (A20-6)
    EPA (A49-56) - EPA (A20-5)
    VCP2 (A49-33) - VCP2 (A20-1)
    VPA2 (A49-14) - VPA2 (A20-3)
    EPA2 (A49-55) - EPA2 (A20-2)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VCPA (A49-34) or VCPA (A20-4) - Body ground
    10 kΩ or higher
    VPA (A49-15) or VPA (A20-6) - Body ground
    EPA (A49-56) or EPA (A20-5) - Body ground
    VCP2 (A49-33) or VCP2 (A20-1) - Body ground
    VPA2 (A49-14) or VPA2 (A20-3) - Body ground
    EPA2 (A49-55) or EPA2 (A20-2) - Body ground

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ECM (VC VOLTAGE)

  1. A109192E03
    Disconnect the A20 accelerator pedal position sensor connector.

  1. Measure the voltage between the terminals of the accelerator pedal position sensor connector.

    Standard voltage:
    Tester Connections
    Specified Conditions
    VCP2 (A20-1) - EPA2 (A20-2)
    4.5 to 5.5 V
    VCPA (A20-4) - EPA (A20-5)

  1. Reconnect the accelerator pedal position sensor connector.



NG
REPLACE ECM
OK

REPLACE ACCELERATOR PEDAL ASSEMBLY (ACCELERATOR PEDAL POSITION SENSOR)


← P0704 Clutch Switch Input Circuit Malfunction (from Nov 2005)P1121 Accelerator Pedal Position Sensor Range / Performance Problem (from Nov 2005) →