2005-2008 Yaris · Service Manual ENGINE

P0335 Crankshaft Position Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and a pickup coil. The sensor plate has 58 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and magnet. The sensor plate rotates and as each tooth passes through the pickup coil, a pulse signal is created.
The pickup coil generates 58 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the common rail system is controlled.
DTC No.
DTC Detection Conditions
Trouble Areas
P0335
No crankshaft position sensor signal to ECM while cranking
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft position sensor plate
  4. ECM

HINT:
DTC P0335 is detected when the engine cranks 8 revolutions or more.

Reference: Inspection using the oscilloscope.
A129228E01

HINT:
  1. The correct waveform is as shown on the left.
  2. G stands for the camshaft position sensor signal, and NE+ stands for the crankshaft position sensor signal.
  3. Grounding failure of the shielded wire may cause noise in waveforms.

Item
Contents
Terminal
CH1: G1 - EG
CH2: NE+ - NE-
Equipment Setting
10 ms/Division
Condition
While cranking or idling

WIRING DIAGRAM

A122594E02

INSPECTION PROCEDURE

HINT:
  1. Check the value on an intelligent tester.
    1. Connect an intelligent tester to the DLC3.
    2. Start the engine and turn the tester on.
    3. Select the following menu items: Powertrain / Engine and ECT / Data List / Engine SPD.
  2. The engine speed can be confirmed in the Data List using the intelligent tester. If there are no NE signals from the crankshaft position sensor despite the engine revolving, the engine speed will be indicated as zero. If the voltage output of the crankshaft position sensor is insufficient, the engine speed will be indicated as lower than the actual engine rpm.


1. INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)

  1. A122681E01
    Disconnect the C44 crankshaft position sensor connector.

  1. Measure the resistance between terminals 1 and 2.

    Standard resistance:
    Tester Connections
    Specified Conditions
    1 - 2
    1,630 to 2,740 Ω at cold
    1 - 2
    2,065 to 3,225 Ω at hot

    HINT:
    Terms "cold" and "hot" refer to the temperature of the coils. "Cold" means approximately -10° to 50°C (14° to 122°F). "Hot" means approximately 50° to 100°C (122° to 212°F).

  1. Reconnect the crankshaft position sensor connector.



NG
REPLACE CRANKSHAFT POSITION SENSOR
OK


2. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

  1. A122680E01
    Disconnect the C44 crankshaft position sensor connector.

  1. Disconnect the C50 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    NE+ (C44-1) - NE+ (C50-10)
    Below 1 Ω
    NE- (C44-2) - NE- (C50-11)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    NE+ (C44-1) or NE+ (C50-10) - Body ground
    10 kΩ or higher
    NE- (C44-2) or NE- (C50-11) - Body ground

  1. Reconnect the crankshaft position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

  1. BR03795E25
    Check the crankshaft position sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR
OK


4. CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
  1. Check the teeth of the sensor plate.

    OK:
    Sensor plate does not have any cracks or deformation.



NG
REPLACE CRANKSHAFT POSITION SENSOR PLATE
OK


5. REPLACE CRANKSHAFT POSITION SENSOR

NEXT


6. CHECK WHETHER DTC OUTPUT RECURS (DTC P0335)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Select the following menu item: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    No output
    A
    P0335
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM
A

END


← P0263 Cylinder 1 Contribution / Balance (+ P0266, P0269, P0272, P0300) (from Nov 2005)P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (from Nov 2005) →