2005-2008 Yaris · Service Manual ENGINE

P0263 Cylinder 1 Contribution / Balance

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

CAUTION / NOTICE / HINT

HINT:
  1. If DTC P0263 is displayed, check the No. 1 cylinder.
  2. If DTC P0266 is displayed, check the No. 2 cylinder.
  3. If DTC P0269 is displayed, check the No. 3 cylinder.
  4. If DTC P0272 is displayed, check the No. 4 cylinder.


DESCRIPTION

Misfire: The ECM uses the crankshaft position sensor and camshaft position sensor to monitor changes in the crankshaft rotation for each cylinder.
The ECM counts the number of times the engine speed change rate indicates that a misfire has occurred.
And when the misfire rate equals or exceeds the threshold indicating that the engine condition has deteriorated, the MIL lights up.

HINT:
  1. The cylinder, which has the compensation value for Revised Injection Volume #1, #2, #3 or #4 that varies from the other cylinders, may be malfunctioning.
  2. If only DTCs P0263, P0266, P0269, P0272 and/or P0300 are present, an injector mechanical malfunction (valve clearance etc) or insufficient compression has probably occurred. An open or short malfunction of the ECM or injector circuit is unlikely.

DTC No.
DTC Detection Conditions
Main Trouble Areas
Related Trouble Areas
P0263
P0266
P0269
P0272
P0300
Significant fluctuations in engine speed while idling
(The MIL is illuminated and a DTC is set when the same malfunction is detected on 2 consecutive trips*
*: One trip is counted when the ignition switch is turned from off to on (IG) and back to off)
  1. Injector
  2. Open or short in engine wire harness.
  3. Connector connection
  4. Compression pressure
  5. Valve clearance
  1. Valve timing
  2. ECM
  3. Low quality fuel
  4. Injector compensation code

HINT:
These DTCs are set when the engine idles for 10 minutes or more with a warmed up engine.


WIRING DIAGRAM

Refer to DTC P0201 (Click here).

INSPECTION PROCEDURE

HINT:
  1. If any DTCs other than P0263, P0266, P0269, P0272 and/or P0300 are set simultaneously, troubleshoot those DTCs first.
  2. Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0263, P0266, P0269, P0272 AND/OR P0300)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    HINT:
    If any DTCs other than P0263, P0266, P0269, P0272 and/or P0300 are output, troubleshoot those DTCs first.

    Result:
    Display (DTC Output)
    Proceed To
    P0263, P0266, P0269, P0272 and/or P0300
    A
    "P0263, P0266, P0269, P0272 and/or P0300" and other DTCs
    B



B
GO TO DTC CHART
A


2. CHECK INJECTOR COMPENSATION CODE
  1. Check injector compensation code (Click here).

    OK:
    The compensation codes stored in the ECM match the compensation codes of the installed injectors.



NG
REGISTER INJECTOR COMPENSATION CODE
OK


3. CHECK WIRE HARNESS AND CONNECTOR IN ENGINE ROOM
  1. Check the wire harness and connector connections.

    OK:
    The wire harnesses and connectors have been connected securely and there are good connections.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. READ VALUE USING INTELLIGENT TESTER (COMPENSATORY INJECTION VOLUME BETWEEN CYLINDERS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Revised Injection Volume #1, #2, #3 and #4.

  1. Read the values displayed on the tester.

    Standard:
    The compensatory injection volume is between -2.0 mm3 and 2.0 mm3.

    HINT:
    1. If the injector is malfunctioning, the compensatory injection volume remains at -5.0 mm3 or 5.0 mm3.
    2. The compensatory injection volume is usually between -2.0 mm3 and 2.0 mm3.

  1. Any cylinders that have a higher compensatory injection volume than shown above are considered to be faulty. Use the following steps to inspect and repair the cylinders.

    Result:
    Result
    Proceed To
    Faulty cylinder not identified
    A
    Faulty cylinder identified
    B



B
Go to step 6
A


5. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Injector cut #1, #2, #3 and #4.

  1. Check the four cylinders in sequence to identify a faulty cylinder by performing the power-balance inspection.

    HINT:
    If the engine idling remains normal despite cutting off the fuel injection, the cylinder is malfunctioning.


NEXT


6. CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
  1. Measure the compression pressure.

    Standard (minimum pressure):
    2,200 kPa (22.5 kgf/cm2, 320 psi)

    Standard (difference between each cylinder):
    500 kPa (5.0 kgf/cm2, 71 psi)

    OK:
    The cylinder compression pressure is within the standard range.



NG
REPAIR OR REPLACE VALVE SPRING (VALVE SPRING, PISTON RING AND/OR VALVE TIMING)
OK


7. CHECK VALVE CLEARANCE OF MALFUNCTIONING CYLINDER
  1. Check the valve clearance (Click here).

OK:
The valve clearance is within the standard range.



NG
ADJUST VALVE CLEARANCE
OK


8. CHECK WHETHER DTC OUTPUT RECURS (DTC P0263, P0266, P0269, P0272 AND/OR P0300)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Clear DTCs (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the tester.

  1. Drive the vehicle for more than 10 minutes.

  1. Read DTCs using the tester.

OK:
No DTC output.



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


9. REPLACE INJECTOR ASSEMBLY
  1. Replace an injector assembly (Click here).

HINT:
Register injector compensation code (Click here).


NEXT


10. CHECK WHETHER DTC OUTPUT RECURS (DTC P0263, P0266, P0269, P0272 AND/OR P0300)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Clear DTCs (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the tester.

  1. Drive the vehicle for more than 10 minutes.

  1. Read DTCs using the tester.

OK:
No DTC output.



NG
REPLACE ECM
OK

SYSTEM OK


← P0252 Injection Pump Fuel Metering Control "A" Range / Performance (Cam / Rotor / Injector) (+ P1228) (from Nov 2005)P0335 Crankshaft Position Sensor "A" Circuit (from Nov 2005) →