2005-2008 Yaris · Service Manual ENGINE

P0403 Exhaust Gas Recirculation Control Circuit

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

Refer to DTC P0400 (Click here).
DTC No.
DTC Detection Conditions
Trouble Areas
P0403
Open or short in EGR valve circuit
(The MIL is illuminated and a DTC is set when the same malfunction is detected on 2 consecutive trips*
*: One trip is counted when the ignition switch is turned from off to on (IG) and back to off)
  1. Open or short in EGR circuit
  2. EGR valve assembly
  3. ECM

HINT:
DTC P0403 is set when the ignition switch is in the on (IG) position.


WIRING DIAGRAM

Refer to DTC P0400 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. INSPECT EGR VALVE ASSEMBLY

  1. A122610E02
    Disconnect C52 EGR valve connector.

  1. Measure the resistance between the terminals of the EGR valve connector.

    Standard resistance:
    Tester Connections
    Specified Conditions
    +B2 (5) - EGR1 (4)
    18.2 to 21.0 Ω at 20°C (68°F)
    +B2 (5) - EGR3 (6)
    +B1 (2) - EGR2 (1)
    +B1 (2) - EGR4 (3)



NG
REPLACE EGR VALVE ASSEMBLY
OK


2. CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)

  1. A122611E02
    Disconnect the C52 EGR valve connector.

  1. Disconnect the A49 EGR valve connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    EGR1 (A49-12) - EGR1 (C52-4)
    Below 1 Ω
    EGR2 (A49-11) - EGR2 (C52-1)
    EGR3 (A49-31) - EGR3 (C52-6)
    EGR4 (A49-30) - EGR4 (C52-3)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    EGR1 (A49-12) or EGR1 (C52-4) - Body ground
    10 kΩ higher
    EGR2 (A49-11) or EGR2 (C52-1) - Body ground
    EGR3 (A49-31) or EGR3 (C52-6) - Body ground
    EGR4 (A49-30) or EGR4 (C52-3) - Body ground

  1. Reconnect the EGR valve connector.

  1. Reconnect the ECM connector.



OK
REPLACE ECM
NG


3. CHECK FUSE (ECD2 FUSE)

  1. A107902E03
    Remove the ECD2 fuse from the engine room relay block.

  1. Check the ECD2 fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the ECD2 fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK

CHECK ECM POWER SOURCE CIRCUIT


← P0400 Exhaust Gas Recirculation Flow (from Nov 2005)P0500 Vehicle Speed Sensor "A" (from Nov 2005) →