2005-2008 Yaris · Service Manual ENGINE

P0500 Vehicle Speed Sensor "A"

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU and wheel speed sensor. The wheel speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of the pulse signal.
A115899E02
DTC No.
DTC Detection Conditions
Trouble Areas
P0500
No vehicle speed sensor signal to ECM while vehicle driven with highly loaded engine and in high gear
(The MIL is illuminated and a DTC is set when the same malfunction is detected on 2 consecutive trips*
*: One trip is counted when the ignition switch is turned from off to on (IG) and back to off)
  1. Open or short in speed sensor circuit
  2. Speed sensor
  3. Combination meter
  4. ECM

HINT:
DTC P0500 is set when the vehicle is driven with a highly loaded engine and in high gear.


WIRING DIAGRAM

A112582E06

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK OPERATION OF SPEEDOMETER
  1. Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

    HINT:
    1. The vehicle speed sensor is operating normally if the speedometer reading is normal.
    2. If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (Click here).



NG
GO TO MALFUNCTION IN SPEEDOMETER
OK


2. READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Vehicle SPD.

  1. Drive the vehicle.

  1. Read the value displayed on the tester.

    OK:
    Vehicle speeds displayed on tester and speedometer display are equal.



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


3. CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)

  1. A122532E02
    Disconnect the D1 combination meter connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminal of the combination meter and the body ground.

    Standard voltage:
    Tester Connections
    Specified Conditions
    +S (D1-16) - Body ground
    4.5 to 5.5 V

  1. Reconnect the combination meter connector.



NG
Go to step 5
OK


4. CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)

  1. A122538E03
    Shift the transmission gear selector lever to the neutral position.

  1. Jack up the vehicle.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminal of the combination meter and the body ground while the wheel is turned slowly.

    Standard voltage:
    Tester Connections
    Specified Conditions
    +S (D1-16) - Body ground
    Voltage generated intermittently

    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.



NG
REPLACE COMBINATION METER ASSEMBLY
OK


5. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

  1. A122667E01
    Disconnect the D1 combination meter connector.

  1. Disconnect the A49 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    +S (D1-16) - (A49-66)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    +S (D1-16) or SPD (A49-66) Body ground
    10 kΩ or higher

  1. Reconnect the combination meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0403 Exhaust Gas Recirculation Control Circuit (from Nov 2005)P0603 Internal Control Module Keep Alive Memory (KAM) Error (from Nov 2005) →