2005-2008 Yaris · Service Manual ENGINE

P0380 Glow Plug / Heater Circuit "A" Malfunction

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

The glow plug is mounted inside the engine combustion chamber. To ensure efficient engine starting with a cold engine, the ECM calculates the time interval the current needs to flow through the glow plug, depending on the starting engine coolant temperature when the ignition switch is turned on (IG). The ECM then turns on the glow plug relay and permits the current to flow through the glow plug based on the ECM's calculated time. The glow plug is then heated, and enhances fuel combustion with a cold engine.
DTC No.
DTC Detection Conditions
Trouble Areas
P0380
When glow plug is turned from OFF to ON, current does not flow through glow plug relay
(The MIL is illuminated and a DTC is set when the same malfunction is detected on 2 consecutive trips*
*: One trip is counted when the ignition switch is turned from off to on (IG) and back to off)
  1. Glow plug relay
  2. ECM

HINT:
DTC P0380 is set when the ignition switch is in the on (IG) position after cold soak.


WIRING DIAGRAM

A115987E02

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. INSPECT GLOW PLUG RELAY ASSEMBLY

  1. A122605E02
    Disconnect the C65 glow plug relay connector.

  1. Check the glow plug relay resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    3 - 4
    10 kΩ or higher
    3 - 4
    Below 1 Ω
    (When battery voltage applied to terminals 1 and 2)

  1. Reinstall the glow plug relay connector.



NG
REPLACE GLOW PLUG RELAY ASSEMBLY
OK


2. CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY - ECM)

  1. A122668E01
    Disconnect the A49 ECM connector.

  1. Disconnect the C65 glow plug relay connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    (C65-2) - GREL (A49-81)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    GREL (A49-81) or (C65-2) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the glow plug relay connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK FUSE (ECD2 FUSE)

  1. A107902E03
    Remove the ECD2 fuse from the engine room relay block.

  1. Check the ECD2 fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the ECD2 fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


4. CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY - ECD RELAY)

  1. A122669E01
    Disconnect the C65 glow plug relay connector.

  1. Remove the integration relay from the engine room relay block.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    (C65-1) - Integration Relay (1A-8)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    (C65 -1) or Integration Relay (1A-8) - Body ground
    10 kΩ or higher

  1. Reconnect the glow plug relay connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (GLOW PLUG - GLOW PLUG RELAY - BATTERY)

  1. A122670E01
    Disconnect the C65 glow plug relay connector.

  1. Disconnect the C64 glow plug wire.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    (C65-3) - Glow plug wire (C64)
    Below 1 Ω
    (C65-4) - Battery positive terminal

  1. Disconnect the glow plug relay connector.

  1. Reconnect the glow plug wire.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (from Nov 2005)P0400 Exhaust Gas Recirculation Flow (from Nov 2005) →