2005-2008 Yaris · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Nov 2005


INSPECT STARTER ASSEMBLY

NOTICE:
Perform each of the following tests within 3 to 5 seconds.

  1. A127319E01
    Perform pull-in test.

    1. Disconnect the field coil lead wire from terminal C.

    2. Connect the battery to the magnet starter switch assembly as shown in the illustration and check that the pinion gear is extended.

  1. A127320E01
    Perform holding test.

    1. Check that the pinion gear does not return inward after the cable of terminal C is disconnected.

  1. A127321E01
    Inspect the clutch pinion gear return.

    1. Move the pinion gear toward the armature.

  1. A127322E01
    Perform the operation test without load.

    1. Connect the field coil lead wire to terminal C.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    2. Clamp the starter in a vise.

    3. Connect the battery and ammeter to the starter as shown in the illustration.

    4. Check that the ammeter indicates the specified current.

      Standard current:
      65 A or less at 11.5 V


INSPECT STARTER ARMATURE ASSEMBLY

  1. A127312E01
    Check the commutator for open circuits.

    1. Using an ohmmeter, check the resistance between the segments of the commutator.

      Standard resistance:
      Below 1 Ω

      If the result is not as specified, replace the starter armature assembly.

  1. A127313E01
    Check the commutator for ground.

    1. Using an ohmmeter, check the resistance between the commutator and armature core.

      Standard resistance:
      10 kΩ or higher

      If the result is not as specified, replace starter armature assembly.

  1. Check the commutator for dirt and burns on the surface.
    If the surface is dirty or burnt, restore it with sandpaper (No. 400) or a lathe.

  1. A127314
    Check the commutator circumference runout.

    1. Place the commutator on V-blocks.

    2. Using a dial indicator, measure the circumference runout.

      Standard runout:
      0.02 mm (0.0008 in.)

      Maximum runout:
      0.04 mm (0.0016 in.)

      If the runout is greater than the maximum, replace the starter armature assembly.

  1. A127315E01
    Using vernier calipers, measure the commutator diameter.

    Standard diameter:
    35.0 mm (1.378 in.)

    Minimum diameter:
    33.8 mm (1.3307 in.)

    If the diameter is less than the minimum, replace the starter armature assembly.

  1. A105577
    Using vernier calipers, measure the undercut depth of the commutator.

    Standard depth:
    0.9 mm (0.0354 in.)

    Minimum depth:
    0.4 mm (0.0157 in.)

    If the undercut depth is less than the minimum, adjust it with a hacksaw blade.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. A128439E01
    Using vernier calipers, measure the brush length.

    Standard length:
    12.5 mm (0.4921 in.)

    Minimum length:
    7.0 mm (0.2756 in.)

    If the length is less than the minimum, replace the starter brush holder.

  1. A104910E01
    Check the brush holder.

    1. Using an ohmmeter, measure the resistance between the brushes.

      Standard resistance:
      Tester Connection
      Specified Condition
      A - B
      10 kΩ or higher
      A - C
      10 kΩ or higher
      A - D
      Below 1 Ω
      B - C
      Below 1 Ω
      B - D
      10 kΩ or higher
      C - D
      10 kΩ or higher

      If the standard is not met, replace the starter brush holder assembly.


INSPECT STARTER CLUTCH SUB-ASSEMBLY

  1. A127316E01
    Check the starter clutch pinion gear.

    1. Hold the starter clutch and rotate the pinion gear clockwise, and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.
      If necessary, replace the starter clutch sub-assembly.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. A105370E01
    Check the plunger.

    1. Install the plunger and spring onto the switch body.

    2. A104908
      Push in the plunger and check that it returns quickly to its original position.
      If necessary, replace the magnet starter switch assembly.

  1. A127317E01
    Check the pull-in coil for an open circuit.

    1. Using an ohmmeter, check the resistance between terminal 50 and C.

      Standard resistance:
      Below 1 Ω

      If the result is not as specified, replace the magnet starter switch assembly.

  1. A127318E01
    Check whether the holding coil has an open circuit.

    1. Using an ohmmeter, check the resistance between terminal 50 and the switch body.

      Standard resistance:
      Below 1 Ω

      If the result is not as specified, replace the starter switch assembly.

← DISASSEMBLY (from Nov 2005)REASSEMBLY (from Nov 2005) →