2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL THERMOSTAT
  1. Install a new gasket onto the thermostat.

  1. A127231
    Align the jiggle valve of the thermostat with the matchmark of the water inlet and install the thermostat.


2. INSTALL WATER INLET

A129170
  1. Install water inlet with radiator hose with the bolt and nut.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


3. INSTALL E.F.I. ENGINE COOLANT TEMPERATURE SENSOR

A129169
  1. Provisionally install the engine coolant temperature sensor through a new gasket.

  1. Using a 19mm deep socket wrench, tighten the engine coolant temperature sensor.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


4. INSTALL CAMSHAFT POSITION SENSOR

A129168
  1. Install the bolt and install the camshaft position sensor.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


5. INSTALL RADIO SETTING CONDENSER

A129167
  1. Install the bolt and install the radio setting condenser.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


6. INSTALL SPARK PLUG

A131355
  1. Install the 4 spark plugs.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


7. INSTALL HARNESS BRACKET

A129166
  1. Install the bolt and install the harness bracket.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


8. INSTALL FUEL INJECTOR ASSEMBLY

  1. A127656
    Install the 2 insulators onto fuel delivery pipe.

  1. A107004E01
    Apply a light coat of gasoline to 4 new O-rings and 4 new insulators, then install one onto each fuel injector.

  1. Apply a light coat of gasoline to the contact surfaces of the fuel delivery pipe and the O-rings and insulators of the fuel injector.

  1. A127205
    While turning the fuel injectors left and right, install them onto the fuel delivery pipe.

    NOTICE:
    1. Do not twist the O-ring.
    2. After installing the fuel injectors, check that they turn smoothly. If not, replace the O-ring with a new one.


9. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

A129165
  1. Install the fuel delivery pipe sub-assembly with the 4 fuel injectors, then provisionally install the 2 bolts.

    NOTICE:
    1. Do not drop the fuel injectors when installing the fuel delivery pipe sub-assembly.
    2. Check that the fuel injectors rotate smoothly after installing the fuel delivery pipe sub-assembly.

  1. Tighten the 2 bolts to the specified torque.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


10. INSTALL CYLINDER HEAD GASKET

A129164E01
  1. Place a new cylinder head gasket on the cylinder block with the Lot No. stamp facing upward.

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Check the mounting orientation of the cylinder head gasket.
    3. Do not damage the cylinder gasket when installing the cylinder head onto the cylinder block.


11. INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
The cylinder head bolts are tightened in 2 successive steps.

  1. Apply a light coat of engine oil to the threads of the cylinder head bolts.

  1. A129163E02
    Using several steps, install and tighten the 10 cylinder head bolts and plate washers uniformly with an 8 mm bi-hexagon wrench, in the sequence shown in the illustration.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }

  1. Mark the front of the cylinder head bolt with paint.

  1. A129210E01
    Retighten the cylinder head bolts 90° and then an additional 90° as shown in the illustration.

  1. Check that the paint mark is now at a 180° angle from the front.

  1. A129211E01
    Apply a continuous bead of seal packing (Diameter 2.5 mm 0.098 in.)) as shown in the illustration.

    Seal Packing:
    Toyota genuine seal packing black, Three bond 12078B or Equivalent.

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the oil pump assembly within 3 minutes and tighten the bolts within 15 minutes of applying the seal packing.


12. INSTALL CAMSHAFT SUB-ASSEMBLY
  1. Apply new engine oil to the valve lifter and journal of the cylinder head.

  1. A127682
    Place the intake camshaft on the cylinder head so that the cam noses of cylinders No. 3 and No. 4 face as shown in the illustration.

  1. Apply new engine oil to the lifter and journal of the cylinder head.

  1. A127683
    Place the exhaust camshaft on the cylinder head so that the cam nose of cylinders No. 2 and No. 4 may face as shown in the illustration.

  1. A131393
    Make sure that the bearing caps are in the sequence shown in the illustration and install the bearing caps with the 8 bolts.

  1. A131394
    Make sure that the bearing caps are in the sequence shown in the illustration and install the bearing caps with the 8 bolts.

  1. A129162
    Provisionally install the No. 1 camshaft bearing cap and bolt as shown in the illustration.

  1. A131395E01
    Uniformly install the 20 bolts in the sequence shown in the illustration.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }


13. INSTALL CAMSHAFT TIMING SPROCKET ASSEMBLY

A129161
  1. Using the hexagonal portion of the camshaft, hold the camshaft and install the camshaft timing sprocket with the bolt.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }


14. REMOVE OIL PAN SUB-ASSEMBLY
  1. Install the chain block.

  1. Remove the oil pan and jack.


15. INSTALL CHAIN SUB-ASSEMBLY

A129137E01
  1. Align the matchmarks of the crankshaft sprocket and the timing chain and install the timing chain.

  1. A129139E01
    Align the matchmarks of the camshaft timing sprocket and the camshaft timing gear or sprocket with the timing marks of the timing chain and install the timing chain.


16. INSTALL NO. 2 TIMING CHAIN GUIDE

A129136
  1. Install the No. 2 timing chain guide with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


17. INSTALL TIMING CHAIN GUIDE

A129135
  1. Install the timing chain guide with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


18. INSTALL TIMING CHAIN TENSION ARM

A129134
  1. Install the timing chain tension arm with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


19. INSTALL CHAIN TENSIONER PLUNGER

A129133
  1. Install the chain tensioner plunger with the bolt and the nut.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    Using the hexagonal portion of the camshaft, slightly turn the camshaft counterclockwise and install the tensioner plunger with the chain on the tensioner loose.

  1. Remove the 3mm diameter bar from the chain tensioner plunger.


20. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

A083159
  1. Install the No. 1 crankshaft position sensor plate so that mark F can be seen.


21. INSTALL TIMING CHAIN OR BELT COVER OIL SEAL

A108561E02
  1. Using SST, tap in a new oil seal to the specified depth.

    SST
    09636-20010  

    NOTICE:
    Do not tap in the oil seal at an angle.

  1. Apply a small amount of MP grease to the lip of the new oil seal.

    NOTICE:
    Keep the lip free of foreign matter.


22. INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

A129126
  1. Install a new gasket onto the timing chain cover.

  1. Apply seal packing black as shown in the illustration.

    A129140E01

    Seal packing:
    Toyota genuine seal packing black, Three bond 12078B or Equivalent.

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the oil pump assembly within 3 minutes and tighten the bolts and nut within 15 minutes of applying the seal packing.
    3. Do not expose the seal to engine oil for at least 2 hours after the installation.

  1. A129208E01
    Install the 10 bolts, nut and 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf } bolt A or B
    23 N*m{ 238 kgf*cm , 17 ft.*lbf } bolt C
    12 N*m{ 122 kgf*cm , 9 ft.*lbf } nut
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf } stud bolt

    HINT:
    Each bolt length is as follows.
    1. A: 10 mm (0.394 in.)
    2. B: 30 mm (1.181 in.)
    3. C: 35 mm (1.378 in.)


23. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

A129124
  1. Install the engine mounting bracket with the 2 bolts and nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


24. INSTALL ENGINE MOUNTING STAY RH

A129123
  1. Install the engine mounting stay with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


25. INSTALL FAN AND GENERATOR V BELT
  1. Provisionally install the V belt onto the pulleys.


26. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR

A129120
  1. Install the engine mounting insulator with the 5 bolts and nut.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }

  1. A127653
    Install the low pressure pipe bracket of the air conditioner with the bolt.

  1. Install the engine mounting insulator.

    Torque:
    10 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. A127622
    Remove the engine hanger with the bolt.


27. INSTALL OIL PAN SUB-ASSEMBLY

A129209E01
  1. Apply seal packing black (Diameter 4.0 mm 0.157 in.) to the area shown in the illustration.

    Seal Packing:
    Toyota genuine seal packing black, Three bond 12078B or Equivalent.

    NOTICE:
    1. Keep the installation surfaces free of oil.
    2. Install the oil pan within 3 minutes of applying the seal packing black.
    3. Install the oil pan to the specified torque within 15 minutes of applying the seal packing black.
    4. Do not start the engine for at least 2 hours after the installation.

  1. A129121E01
    Install the oil pan with the 2 nuts and 16 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } bolt A
    41 N*m{ 413 kgf*cm , 30 ft.*lbf } bolt B
    13 N*m{ 133 kgf*cm , 10 ft.*lbf } nut

  1. A127698
    Install the service hole cover.


28. INSTALL CAM TIMING OIL CONTROL VALVE ASSEMBLY

  1. A127180
    Install the cam timing oil control valve assembly with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.


29. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY (w/ Air Conditioning System)

A127697
  1. Install the washer and pulley with the bolt and nut.

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf }


30. INSTALL CRANKSHAFT POSITION SENSOR

  1. A127186
    Install the crankshaft position sensor with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the crankshaft position sensor connector.


31. INSTALL IDLER PULLEY SUB-ASSEMBLY (w/ Air Conditioning System)

A127696
  1. Install the washer and pulley with the nut.

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf }


32. INSTALL WATER PUMP PULLEY

A129122E01
  1. Using SST, hold the water pump pulley and install the water it pump pulley with the 4 bolts.

    Torque:
    12 N*m{ 117 kgf*cm , 9 ft.*lbf }

    SST
    09960-10010   (09963-00500)


33. INSTALL CRANKSHAFT PULLEY

  1. A129213E01
    w/o service hole:

    1. Hold the crankshaft pulley with SST and tighten the bolt.

      SST
      09960-10010   (09963-00500)

      Torque:
      150 N*m{ 1530 kgf*cm , 111 ft.*lbf }

  1. A131374E01
    w/ service hole:

    1. Hold the crankshaft pulley with SST and tighten the bolt.

      SST
      09330-00021  
      09213-54015   (91651-60855)

      Torque:
      150 N*m{ 1530 kgf*cm , 111 ft.*lbf }


34. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

A127688
  1. Apply seal packing black to the area shown in the illustration.

    Seal Packing:
    Toyota genuine seal packing black, Three bond 12078B or Equivalent.

    NOTICE:
    1. Keep the installation surface free of foreign matter and oil.
    2. Install the No. 2 timing chain or belt cover within 3 minutes of applying the seal packing.
    3. Do not start the engine for at least 2 hours after the installation.

  1. A127662E01
    Using the several steps, install the cylinder head cover with the 11 bolts and the nut.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }


35. CONNECT ENGINE WIRE (for RHD)

A127661
  1. Connect the engine wire harness with the 2 bolts..

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. A127659
    Connect the engine wire harness clamp.


36. CONNECT ENGINE WIRE (for LHD)

A127661
  1. Install the engine wire harness with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. A127660
    Connect the 2 engine wire harness clamps.


37. INSTALL OIL LEVEL GAGE SUB-ASSEMBLY

38. INSTALL IGNITION COIL ASSEMBLY

  1. A127192
    Install the 4 ignition coil assembly with the 4 bolts.

    Torque:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }

  1. A127191
    Connect the 4 ignition coil assembly connectors.


39. INSTALL FUEL HOSE SUB-ASSEMBLY

A127655
  1. Align the fuel tube connector with the pipe, then push the fuel tube connector in until the retainer makes a click sound.

    NOTICE:
    1. Check that there are no scratches or foreign matter on the fuel tube connector and pipe joint.
    2. After connecting the fuel tube, pull the pipe and fuel tube connector to make sure that they are securely connected.

  1. A127194
    Install the fuel pipe clamp.


40. INSTALL HEATER WATER OUTLET HOSE A

A129160
  1. Connect the heater water outlet hose A.


41. INSTALL HEATER WATER INLET HOSE A

A129159
  1. Connect heater water inlet hose A.


42. CONNECT NO. 2 RADIATOR HOSE

A129158
  1. Connect the No. 2 radiator hose.


43. CONNECT NO. 1 RADIATOR HOSE

A129157
  1. Connect the No. 1 radiator hose.


44. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

  1. A135336
    Install the bolt and wire harness clamp.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. A109351E01
    Using several steps, install a new exhaust manifold gasket and exhaust manifold with the 3 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf } nut


45. INSTALL MANIFOLD STAY

A127627E01
  1. Install the bolt and nut with the manifold stay.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf } bolt

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf } nut


46. INSTALL NO. 1EXHAUST MANIFOLD HEAT INSULATOR

A129156
  1. Install the manifold heat insulator with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


47. INSTALL WIRING HARNESS CLAMP BRACKET

A129155
  1. Install the wiring harness clamp bracket with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. A129154
    Connect the oxygen sensor connector.


48. INSTALL INTAKE MANIFOLD
  1. Install a new intake manifold gasket.

  1. A127169
    Provisionally install the intake manifold with the 3 bolts and 2 nuts.

  1. A109351
    Tighten the 3 bolts and 2 nuts in the sequence order shown in the illustration.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


49. INSTALL THROTTLE BODY BRACKET

A127168
  1. Install the throttle body bracket with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


50. CONNECT ENGINE WIRE (for RHD)

  1. A127166
    Engage the engine wire harness clamp.


51. CONNECT ENGINE WIRE (for LHD)

  1. A131384
    Install the engine wire harness bracket with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. A127165
    Connect the 2 engine wire harness clamps.


52. CONNECT VENTILATION HOSE (for RHD)

  1. A131384
    Install the engine wire harness bracket with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. A127164
    Connect the ventilation hose to the cylinder head.


53. CONNECT VENTILATION HOSE (for LHD)

  1. A127163
    Connect the ventilation hose to the cylinder head.


54. CONNECT UNION TO CONNECTOR TUBE HOSE (for RHD)

  1. A127162
    Connect the union to connector tube hose.


55. CONNECT UNION TO CONNECTOR TUBE HOSE (for LHD)

  1. A127161
    Connect the union to connector tube hose.


56. INSTALL THROTTLE BODY ASSEMBLY

  1. A127156
    Install a new O-ring.

  1. A127155E01
    Install the throttle body assembly with the 3 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf } for bolt A
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf } for bolt B

  1. A127154
    Connect the connector to the throttle body assembly.


57. CONNECT CHARCOAL CANISTER FUEL HOSE

  1. A127153
    Connect the charcoal canister fuel hose to the throttle body assembly.


58. CONNECT NO. 2 VENTILATION HOSE

  1. A127152
    Connect the No. 2 ventilation hose to the throttle body assembly.


59. CONNECT NO. 1 WATER BY-PASS HOSE

  1. A127150
    Connect the 2 No. 1 water by-pass hoses.


60. INSTALL AIR CLEANER ASSEMBLY

  1. A127151
    Install a new O-ring.

  1. A127149
    Install the air cleaner case sub-assembly with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. A127148
    Connect the connector to the mass air flow meter.


61. INSTALL PURGE VSV ASSEMBLY

  1. A127147
    Install the bolt and install the purge VSV assembly.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


62. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

63. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

  1. A127144
    Install the air cleaner cap with the grommet and 2 clamps.


64. INSTALL COWL TOP PANEL OUTER

  1. A131385
    Install the cowl top panel outer with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. A131386
    Engage the clamp and install the wiper motor connector wire harness.


65. INSTALL NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

  1. A118801E01
    Engage the 2 claws and install cowl to register duct No. 2.


66. INSTALL WINDSHIELD WIPER MOTOR AND LINK

E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


67. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.


68. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113854
  1. Connect the washer hose.

  1. E113852
    Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.

  1. E117641
    Engage the 2 hooks and install cowl top ventilator louver center No. 1.


69. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.


70. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E113854
  1. Connect the washer hose.

  1. E113852
    Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.

  1. E117641
    Engage the 2 hooks and install cowl top ventilator louver center No. 1.


71. INSTALL HOOD TO COWL TOP SEAL

E113851
  1. Engage the 7 clips and install the hood to cowl top seal.


72. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113863E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


73. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113862E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


74. INSTALL FRONT WIPER ARM HEAD CAP

E113849
  1. Engage the claw and install the 2 front wiper arm head caps.


75. INSTALL HOOD SUB-ASSEMBLY

76. INSPECT HOOD SUB-ASSEMBLY

  1. Check that the clearance measurements are within the standard ranges.

    B118065E01

    Standard:
    Area
    Measurement
    Area
    Measurement
    A
    1.7 to 5.7 mm
    (0.067 to 0.224 in.)
    G
    -1.55 to 2.45 mm
    (-0.061 to 0.096 in.)
    B
    -2 to 2 mm
    (-0.079 to 0.079 in.)
    H
    1.75 to 5.75 mm
    (0.067 to 0.226 in.)
    C
    4.45 to 10.45 mm
    (0.175 to 0.411 in.)
    I
    -1.25 to 2.75 mm
    (-0.049 to 0.108 in.)
    D
    -0.95 to 5.05 mm
    (-0.037 to 0.199 in.)
    J
    -1.5 to 1.5 mm
    (-0.059 to 0.059 in.)
    E
    7.55 to 13.55 mm
    (0.297 to 0.533 in.)
    K
    2.0 to 5.0 mm
    (0.079 to 0.197 in.)
    F
    1.65 to 5.65 mm
    (0.065 to 0.222 in.)
    -
    -


77. ADJUST HOOD SUB-ASSEMBLY

  1. B106963
    Loosen the hood side hinge bolts.

  1. Move the hood to adjust the clearance to within the standard range.

  1. Tighten the hood side hinge bolts after the adjustment.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. B106965
    Adjust the height of the hood front end by turning the cushion rubber.

    HINT:
    The cushion rubber can be raised and lowered by turning it.

  1. B106964
    Adjust the hood lock.

    1. Loosen the 3 bolts.

    2. Adjust the hood lock position so that the striker can enter it smoothly.

    3. Tighten the 3 bolts after the adjustment.

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


78. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }


79. INSTALL FRONT EXHAUST PIPE ASSEMBLY

  1. A104634
    Using vernier calipers, measure the free length of the compression spring.

    Minimum length:
    40.5 mm (1.594 in.)

    If the length is not as specified, replace the compression spring.

  1. A104635E01
    Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

    NOTICE:
    1. Install the exhaust pipe gasket in the correct direction.
    2. Do not damage the outer surface of the exhaust pipe gasket.
    3. Do not reuse the exhaust pipe gasket.
    4. Do not push in the gasket with the exhaust pipe when connecting it.

  1. Install the 3 No. 4 exhaust pipe supports.

  1. Install the exhaust pipe assembly front and a new exhaust pipe gasket with the 4 compression springs and 4 bolts.

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }


80. ADD ENGINE COOLANT
  1. Tighten all the plugs.

  1. Disconnect the vinyl hose.

  1. Pour engine coolant into the radiator assembly until it overflows.

    Capacity:
    5.1 liters (5.4 USqts, 4.5 lmp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.

  1. Install the radiator cap sub-assembly securely.

  1. Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Stop the engine and wait until the coolant cools down.

  1. If the engine coolant level is below the full level, perform steps (c) through (h) again and repeat the operation until the engine coolant level stays at the full level.

  1. Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add engine coolant.


81. ADD ENGINE OIL
  1. Fill with new engine oil.

    Oil capacity:
    Item
    Capacity
    With oil filter change
    3.2 liters (3.4 US qts, 2.8 lmp. qts)
    Without oil filter change
    2.9 liters (3.1 US qts, 2.6 lmp. qts)
    Dry fill
    3.6 liters (3.8 US qts, 3.2 lmp. qts)


82. CHECK FOR ENGINE OIL LEVEL
  1. Warm up the engine, then stop the engine and wait for 5 minutes. Check that the engine oil level is between the low and full marks on the oil level gauge.
    If the engine oil level is low, check for oil leakage and add engine oil up to the full level mark.

    NOTICE:
    Do not add engine oil to above the full level mark.


83. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


84. CHECK FOR ENGINE OIL LEAKAGE

85. CHECK FOR ENGINE COOLANT LEAK

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. A127379
    Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump it to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.


86. CHECK FOR EXHAUST GAS LEAK

87. CHECK FOR FUEL LEAK

  1. A127178E01
    When using the intelligent tester.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and the intelligent tester main switch ON.

      NOTICE:
      Do not start the engine.

    3. Select the Active Test mode on the intelligent tester.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

  1. Check that there is no fuel leakage anywhere in the fuel system after doing maintenance.


88. INSTALL ENGINE UNDER COVER LH

89. INSTALL ENGINE UNDER COVER RH
← REASSEMBLY (from Nov 2005)REPAIR (from Nov 2005) →