2005-2008 Yaris · Service Manual ENGINE

REPLACEMENT

Removal / installation · Vehicles built from Nov 2005


1. REMOVE INTAKE VALVE GUIDE BUSH

  1. A129391E01
    Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. A129392E01
    Using SST and a hammer, tap out the intake valve guide bushing.
    SST
    09950-70010   (09951-07100)
    09201-10000   (09201-01050)


2. REMOVE EXHAUST VALVE GUIDE BUSH

  1. A129391E01
    Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. A129393E01
    Using SST and a hammer, tap out the exhaust valve guide bushing.
    SST
    09950-70010   (09951-07100)
    09201-10000   (09201-01050)


3. INSTALL INTAKE VALVE GUIDE BUSH

  1. A129394
    Using a caliper gauge, measure the bushing bore diameter of the cylinder head.

    Inside diameter:
    9.735 to 9.755 mm (0.38327 to 0.38406 in.)

    If the bushing bore diameter of the cylinder head is greater than 9.706 mm (0.38213 in.), machine the bushing bore to the dimension of 9.735 to 9.755 mm (0.3833 to 0.3841 in.).

    Bushing bore diameter
    mm (in.)
    Bushing size
    9.685 to 9.706
    (0.38130 to 0.38213)
    STD
    9.735 to 9.755
    (0.38327 to 0.38406)
    O/S 0.05

    HINT:
    If the bushing bore diameter of the cylinder head is greater than 9.755 mm (0.38406 in.), replace the cylinder head.

  1. A129391E01
    Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. A129396E01
    Using SST and a hammer, tap a new guide bushing in to the specified protrusion height.
    SST
    09950-70010   (09951-07100)
    09201-10000   (09201-01050)

    Protrusion height:
    14.2 to 14.8 mm (0.559 to 0.583 in.)

  1. A129398E01
    Using a sharp 5 mm reamer, ream the guide bushing to obtain the standard oil clearance between the guide bushing and the valve stem.

    Standard oil clearance:
    0.010 to 0.055 mm (0.00039 to 0.00217 in.)


4. INSTALL EXHAUST VALVE GUIDE BUSH

  1. A129395
    Using a caliper gauge, measure the bushing bore diameter of the cylinder head.

    Inside diameter:
    9.735 to 9.755 mm (0.38327 to 0.38406 in.)

    If the bushing bore diameter of the cylinder head is greater than 9.706 mm (0.38213 in.), machine the bushing bore to the dimension of 9.735 to 9.755 mm (0.3833 to 0.3841 in.).

    Bushing bore diameter
    mm (in.)
    Bushing size
    9.685 to 9.706
    (0.38130 to 0.38213)
    STD
    9.735 to 9.755
    (0.38327 to 0.38406)
    O/S 0.05

    HINT:
    If the bushing bore diameter of the cylinder head is greater than 9.755 mm (0.38406 in.), replace the cylinder head.

  1. A129391E01
    Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. A129397E01
    Using SST and a hammer, tap a new guide bushing in to the specified protrusion height.
    SST
    09950-70010   (09951-07100)
    09201-10000   (09201-01050)

    Protrusion height:
    14.2 to 14.8 mm (0.559 to 0.583 in.)

  1. A129399E01
    Using a sharp 5 mm reamer, ream the guide bushing to obtain the standard oil clearance between the guide bushing and valve stem.

    Standard oil clearance:
    0.020 to 0.065 mm (0.00079 to 0.00256 in.)

← INSPECTION (from Nov 2005)REASSEMBLY (from Nov 2005) →