2005-2008 Yaris · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Nov 2005


INSPECT STARTER ASSEMBLY

A098209

NOTICE:
Perform each of the following tests within 3 to 5 seconds.

  1. Perform the pull-in test.

    1. Remove the nut, then disconnect the lead wire from terminal C.

    2. A098210E01
      Connect the battery to the starter magnetic switch as shown in the illustration. Check that the clutch pinion gear is extended.
      If the clutch pinion gear does not move, replace the magnet starter switch assembly.

  1. A098211E01
    Perform the hold-in test.

    1. Disconnect the negative (-) lead from terminal C. Check that the clutch pinion gear remains extended.
      If the clutch pinion gear returns inward, replace the magnet starter switch assembly.

  1. A098212E01
    Check the operation.

    1. Disconnect the negative (-) lead from the switch body. Check that the clutch pinion gear returns.
      If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.

  1. A098209
    Perform the no-load performance test.

    1. Connect the lead wire to terminal C. Make sure that the lead is not grounded.

      Torque:
      5.9 N*m{ 60 kgf*cm , 52 in.*lbf }

    2. A098208E01
      Clamp the starter in a vise.

    3. Connect the battery and an ammeter to the starter as shown in the illustration.

    4. Check that the starter rotates smoothly and steadily with the clutch pinion gear extended. Check that the ammeter reads the specified current.

      Specified current:
      100 A or less at 11.5 V

      If the result is not as specified, replace the starter assembly.


INSPECT STARTER YOKE ASSEMBLY

B015494E01

  1. Check the resistance.

    1. Using an ohmmeter, measure the resistance between the lead wire and brush lead.

      Standard resistance:
      1 Ω or less

      If the result is not as specified, replace the starter yoke assembly.

    2. B015495E01
      Using an ohmmeter, measure the resistance between the lead wire and body.

      Standard resistance:
      10 kΩ or higher

      If the result is not as specified, replace the starter yoke assembly.

  1. B015496E01
    Inspect the brush length.

    1. Using vernier calipers, measure the brush length.

      Standard length:
      15.0 mm (0.591 in.)

      Minimum length:
      9.0 mm (0.354 in.)

      If the brush length is less than the minimum, replace the starter yoke assembly.


INSPECT STARTER ARMATURE ASSEMBLY
  1. Check the appearance.

    1. Check that the is no deformation or damage on the starter armature assembly.
      If there any defects, replace the starter armature assembly.

  1. G038412E01
    Check the commutator for open circuits.

    1. Using an ohmmeter, measure the resistance between the segments of commutator.

      Standard resistance:
      1 Ω or less

      If the result is not as specified, replace the starter armature assembly.

  1. G038413E01
    Check the commutator for ground.

    1. Using an ohmmeter, measure the resistance between the commutator and coil core.

      Standard resistance:
      10 kΩ or higher

      If the result is not as specified, replace the starter armature assembly.

  1. P010587E02
    Inspect the diameter.

    1. Using vernier calipers, measure the diameter.

      Standard depth:
      35 mm (1.378 in.)

      Minimum depth:
      34 mm (1.339 in.)

      If the diameter is less than the minimum, replace the starter armature assembly.

  1. ST00040
    Inspect the depth.

    1. Using vernier calipers, measure the undercut depth.

      Standard depth:
      0.7 mm (0.028 in.)

      Minimum depth:
      0.2 mm (0.008 in.)

      If the depth is less than the minimum, replace the starter armature assembly.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

ST01103E01
  1. Inspect the brush length.

    1. Using vernier calipers, measure the brush length.

      Standard length:
      15.0 mm (0.591 in.)

      Minimum length:
      9.0 mm 0.354 in.)

      If the brush length is less than the minimum, replace the starter brush holder assembly.

  1. ST00019E06
    Inspect the brush spring load.

    1. Using a spring scale, measure the load as soon as the spring is detached from the brush.

      Standard load:
      21.5 to 27.5 N (2.2 to 2.8 kgf, 4.9 to 6.2 lbf)

      Minimum load:
      12.7 N (1.3 kgf, 2.9 lbf)

      If the brush spring load is less than the minimum, replace the starter brush holder assembly.

  1. P021088E01
    Check the resistance.

    1. Using an ohmmeter, measure the resistance between the positive (+) and negative (-) brush holders.

      Standard resistance:
      10 kΩ or higher

      If the resistance is not as specified, replace the starter brush holder assembly.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

B015499E01

  1. Check the resistance.

    1. Using an ohmmeter, measure the resistance between terminal 50 and C.

      Standard resistance:
      1 Ω or less

      If the result is not as specified, replace the magnet starter switch assembly.

    2. B015498E01
      Using an ohmmeter, measure the resistance between terminal 50 and the body.

      Standard resistance:
      1 Ω or less

      If the result is not as specified, replace the magnet starter switch assembly.


INSPECT STARTER CLUTCH SUB-ASSEMBLY

P024184E01
  1. Check the starter clutch.

    1. Rotate the clutch pinion gear counterclockwise, and check that it turns freely. Try to rotate the clutch pinion gear clockwise, and check that it locks.
      If necessary, replace the starter clutch assembly.

← DISASSEMBLY (from Nov 2005)REASSEMBLY (from Nov 2005) →