2005-2008 Yaris · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Jan 2006


1. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY

  1. B134915E01
    Check the angle of inclination required to lock the retractor.

    1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.

      NOTICE:
      Do not disassemble the retractor.

      If the operation is not as specified, replace the rear center seat outer belt.

  1. B134914
    Insert the hook into the body hole and install the retractor with the bolt.

  1. B138452E01
    for Fixed Seat Type:

    1. Install the anchor plate with the bolt.

      Torque:
      42 N*m{ 430 kgf*cm , 31 ft.*lbf }

      NOTICE:
      1. Install the anchor plate with the arrow mark facing forward.
      2. Do not place the anchor plate over the locating mark area of the floor panel.

  1. Check that the ELR locks.

    NOTICE:
    1. The check should be performed with the rear seat outer belt installed.
    2. Do not allow the anchor part of the rear seat outer belt and the protruding parts of the floor panel to overlap.


    1. With the belt installed, check that the belt locks when it is pulled out quickly.
      If the operation is not as specified, replace the rear center seat outer belt.


2. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

  1. B134912
    Engage the 5 claws and install the package tray trim.

  1. Install the 4 clips.


3. INSTALL HIGH MOUNTED STOP LIGHT ASSEMBLY (w/o Rear Spoiler)

  1. E127792
    Connect the connector.

  1. Engage the 4 claws and install the high mounted stop light assembly.


4. INSTALL ROOF SIDE INNER GARNISH RH

  1. B134775E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the roof side inner garnish.

    2. Engage the 4 clips and the claw and install the roof side inner garnish.

  1. B134774
    w/o Curtain Shield Airbag:

    1. Engage the 4 clips and the claw and install the roof side inner garnish.


5. INSTALL ROOF SIDE INNER GARNISH LH

HINT:
Use the same procedure as for the RH side.


6. INSTALL REAR SEAT SIDE COVER RH

  1. B134776
    Engage the 2 clips and the 4 claws and install the rear seat side cover.


7. INSTALL REAR SEAT SIDE COVER LH

HINT:
Use the same procedure as for the RH side.


8. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

  1. B138636
    Install the rear door opening trim weatherstrip.


9. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


10. INSTALL REAR DOOR SCUFF PLATE RH

  1. B134771
    Engage the 7 claws and install the rear door scuff plate.


11. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


12. INSTALL LUGGAGE COMPARTMENT TRIM INNER PAD (for 60/40 Split Seat Type)

B136275
  1. Install the luggage compartment trim inner pad.


13. INSTALL SPARE WHEEL COVER ASSEMBLY (for 60/40 Split Seat Type)

B136270
  1. Install the spare wheel cover.


14. INSTALL LUGGAGE COMPARTMENT FLOOR MAT (for 60/40 Split Seat Type)

B136269
  1. Install the luggage compartment floor mat.


15. INSTALL REAR SEATBACK ASSEMBLY RH (for 60/40 Split Seat Type)

  1. B134945E01
    Insert the 2 hooks into the rear seatback frame hole and install the rear seatback tightening the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B134944
    Install the rear seatback cover with the 2 clips.

  1. Pull up the rear seatback.

  1. B134943
    Install the rear seat outer belt into the rear seat shoulder belt guide.

  1. for 3 Point Type Rear Seat Belt:

    1. Install the rear center seat outer belt into the rear center seat shoulder belt guide.


16. INSTALL REAR SEATBACK ASSEMBLY LH (for 60/40 Split Seat Type)

  1. B134926E01
    Insert the 2 hooks into the rear seatback frame hole and install the rear seatback tightening the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B134925
    Install the rear seatback cover with the 2 clips.

  1. Pull up the rear seatback.

  1. B134924
    Install the rear seat outer belt into the rear seat shoulder belt guide.


17. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)

  1. B134981
    Engage the 3 hooks and install the rear seatback.

  1. Tighten the 3 bolts.

    Torque:
    7.9 N*m{ 80 kgf*cm , 70 in.*lbf }

  1. B138450E01
    Install the rear seat outer belt into the rear seat shoulder belt guide.

    HINT:
    Use the same procedure for both sides.

  1. for 3 Point Type Rear Center Seat belt:

    1. Install the rear center seat outer belt into the rear center seat shoulder belt guide.


18. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY
  1. for 60/40 Split Seat Type:

    1. Install the rear seat cushion cover pad sub-assembly (Click here).

  1. for Fixed Seat Type:

    1. Install the rear seat cushion cover pad sub-assembly (Click here).


19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/o Rear Spoiler)

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← REMOVAL (from Jan 2006)COMPONENTS (from Aug 2005) →