DISASSEMBLY
Removal / installation · Vehicles built from Jan 2006
- CAUTION:
- Wear protective gloves. Sharp surfaces on the front seat adjuster frame could cause injuries to your hands.
- HINT:
- The procedure described below is for the driver side of LHD. Use the same procedure for both the front passenger and driver sides of LHD, unless otherwise specified.
| 1. REMOVE FRONT SEAT INNER BELT ASSEMBLY |
for Driver Side:

Disengage the claw and remove the connector.
Remove the 2 clamps.
Using a clip remover, remove the clamp.
for Front Passenger Seat:

Disconnect the occupant detection sensor connector.
Disengage the claw and remove the connector.
Remove the 2 clamps.
Using a clip remover, remove the clamp.
Remove the wire harness from the claw of the front seat cushion inner shield.

Remove the nut and the front seat inner belt.
| 2. REMOVE FRONT SEAT CUSHION INNER SHIELD |
Remove the screw.

Using a screwdriver with its tip wrapped in protective tape, disengage the claw and the clip and remove the front seat cushion outer shield.
| 3. REMOVE VERTICAL ADJUSTER COVER (w/ Vertical Adjuster) |
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the vertical adjuster cover.

| 4. REMOVE VERTICAL ADJUSTER KNOB (w/ Vertical Adjuster) |
Remove the 2 screws and the vertical adjuster knob.

| 5. REMOVE RECLINING ADJUSTER RELEASE HANDLE |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the reclining adjuster release handle.

| 6. REMOVE FRONT SEAT CUSHION OUTER SHIELD |
Remove the screw.

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and the clip and remove the front seat cushion outer shield.
| 7. REMOVE FRONT SEAT CUSHION COVER PAD |
for Driver Side:

Disengage the 2 claws and 7 hooks.
for Front Passenger Side:

Disengage the 2 claws and remove the occupant detection sensor connector.
Disengage the 2 claws and 7 hooks.
Using a clip remover, remove the 2 clips and the front seat cushion cover pad.

| 8. REMOVE FRONT SEAT HEADREST SUPPORT |
Remove the 3 hog rings.

Remove the 2 hog rings.

Disengage the 2 claws and remove the front seat headrest support.

- HINT:
- Use the same procedure for both sides.
| 9. REMOVE FRONT SEATBACK COVER PAD |
Remove the front seatback cover pad.

| 10. REMOVE VERTICAL ADJUSTER SPACER (w/ Vertical Adjuster) |
Disengage the claw and remove the vertical adjuster spacer.

| 11. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
Remove the screw.

Disengage the claw and remove the reclining adjuster inside cover.
| 12. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
w/ Front Seat Side Airbag:

Remove the clamp.
Remove the screw.
Disengage the claw and remove the reclining adjuster inside cover.
| 13. REMOVE RECLINING ADJUSTER OUTSIDE COVER RH |
Remove the screw and the reclining adjuster outside cover.

| 14. REMOVE RECLINING ADJUSTER OUTSIDE COVER LH |
- HINT:
- Use the same procedure as for the RH side.
| 15. REMOVE FRONT SEAT CUSHION LOWER SHIELD RH |
w/ Vertical Adjuster:

Remove the screw.
Disengage the claw and remove the front seat cushion lower shield.
w/o Vertical Adjuster:

Remove the screw.
Disengage the 2 claws and remove the front seat cushion lower shield.
| 16. REMOVE FRONT SEAT CUSHION LOWER SHIELD LH |
w/ Vertical Adjuster:

Remove the screw.
Disengage the 2 claws and remove the front seat cushion lower shield.
w/o Vertical Adjuster:

Remove the screw.
Disengage the claw and remove the front seat cushion lower shield.
| 17. REMOVE FRONT SEAT CUSHION PROTECTOR |
Remove the 2 front seat cushion protectors.

