POWER STEERING GEAR (for Hatchback) > INSTALLATION |
| 1. INSTALL TIE ROD END SUB-ASSEMBLY LH |
![]() |
Temporarily install the lock nut and the tie rod end sub-assembly LH to the steering gear assembly until the matchmarks are aligned, then temporarily tighten the lock nut.
| *a | Matchmark |
| 2. INSTALL TIE ROD END SUB-ASSEMBLY RH |
| 3. INSTALL STEERING GEAR ASSEMBLY |
Install the steering gear assembly onto the front suspension crossmember with the 2 bolts and 2 nuts.
| 4. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
Support the front suspension crossmember with a transmission jack.
![]() |
Provisionally install the front suspension crossmember onto the body with the 6 bolts.
| *1 | Bolt A |
| *2 | Bolt B |
| *3 | Bolt C |
| *a | Front Side |
| Bolt | Underhead Length (mm) |
| A | 38 |
| B | 99 |
| C | 41 |
By inserting SST into the datum holes in the front suspension crossmembers RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.

| *1 | Bolt A | *2 | Bolt B |
| *3 | Bolt C | *4 | for Bolt B with Bolt Strength Class 11T |
| *5 | for Bolt B with Bolt Strength Class 10T | - | - |
| *a | Front Side | *b | Datum Hole |
| *c | OK | *d | NG |
Install the engine moving control rod with the bolt.
| 5. INSTALL FRONT SUSPENSION LOWER ARM LH |
![]() |
Provisionally tighten the lower arm with the 2 bolts.
Install the lower arm onto the steering knuckle with a new castle nut.
Install a new clip.
| 6. INSTALL FRONT SUSPENSION LOWER ARM RH |
| 7. INSTALL FRONT STABILIZER LINK ASSEMBLY LH |
Install the stabilizer link with the 2 nuts.
| 8. INSTALL FRONT STABILIZER LINK ASSEMBLY RH |
| 9. INSTALL TIE ROD END SUB-ASSEMBLY LH |
![]() |
Install the tie rod end onto the steering knuckle with a new castle nut.
Install a new cotter pin.
| 10. INSTALL TIE ROD END SUB-ASSEMBLY RH |
| 11. INSTALL FRONT WHEEL |
| 12. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
![]() |
Install clip B onto the body portion and install No. 1 steering column hole cover onto the body portion with clip A.
| *1 | Clip A |
| *2 | Clip B |
| 13. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY |
![]() |
Align the matchmarks and install the sliding yoke onto the intermediate shaft with bolt B.
| *1 | Bolt A |
| *2 | Bolt B |
| *a | Matchmark |
Tighten bolt A.
| 14. INSTALL COLUMN HOLE COVER SILENCER SHEET |
Install the column hole cover silencer sheet with the 2 clips.
Install the floor carpet.
| 15. INSTALL COWL TOP PANEL OUTER |
![]() |
Install the cowl top panel with the 9 bolts.
![]() |
Connect the wire harness clamp.
| 16. INSTALL COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2 |
![]() |
Engage the claw to install cowl to register duct No. 2.
| 17. INSTALL WINDSHIELD WIPER MOTOR AND LINK |
![]() |
Connect the connector.
Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
Install the front wiper motor and link with the 2 bolts.
| 18. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD) |
![]() |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the 2 clips.
| 19. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD) |
![]() |
Connect the washer hose.
![]() |
Engage the 11 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
![]() |
Engage the 2 hooks and install cowl top ventilator louver center No. 1.
| 20. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD) |
![]() |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the clip.
| 21. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD) |
![]() |
Engage the 10 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
| 22. INSTALL HOOD TO COWL TOP SEAL |
![]() |
Engage the 7 clips and install the hood to cowl top seal.
| 23. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 24. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 25. INSTALL FRONT WIPER ARM HEAD CAP |
![]() |
Engage the claw and install the 2 front wiper arm head caps.
| 26. PROVISIONALLY TIGHTEN HOOD SUB-ASSEMBLY |
Provisionally install the hood with the 4 bolts.
| 27. INSPECT HOOD SUB-ASSEMBLY |
Check that the clearance measurements are within the standard ranges.

| Area | Measurement | Area | Measurement |
| A | 1.7 to 5.7 mm (0.067 to 0.224 in.) | G | -1.55 to 2.45 mm (-0.061 to 0.096 in.) |
| B | -2 to 2 mm (-0.079 to 0.079 in.) | H | 1.75 to 5.75 mm (0.067 to 0.226 in.) |
| C | 4.45 to 10.45 mm (0.175 to 0.411 in.) | I | -1.25 to 2.75 mm (-0.049 to 0.108 in.) |
| D | -0.95 to 5.05 mm (-0.037 to 0.199 in.) | J | -1.5 to 1.5 mm (-0.059 to 0.059 in.) |
| E | 7.55 to 13.55 mm (0.297 to 0.533 in.) | K | 2.0 to 5.0 mm (0.079 to 0.197 in.) |
| F | 1.65 to 5.65 mm (0.065 to 0.222 in.) | - | - |
| 28. ADJUST HOOD SUB-ASSEMBLY |
![]() |
Loosen the hood side hinge bolts.
Move the hood to adjust the clearance to within the standard range.
Tighten the hood side hinge bolts after the adjustment.
![]() |
Adjust the height of the hood front end by turning the cushion rubber.
![]() |
Adjust the hood lock.
Loosen the 3 bolts.
Adjust the hood lock position so that the striker can enter it smoothly.
Tighten the 3 bolts after the adjustment.
| 29. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 30. POSITION FRONT WHEELS FACING STRAIGHT AHEAD |
| 31. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |
| 32. CHECK ABS SPEED SENSOR SIGNAL (w/ ABS) |