Home › TRANSMISSION ยท U441E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

AUTOMATIC TRANSAXLE SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Data List displayed by the intelligent tester, you can read the values of the switches, sensors, actuators and so on without parts removal. Reading the Data List as the first step of troubleshooting is one method of shortening labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn on the tester.

  6. Select the following items: Powertrain / Engine and ECT / Data Test.

  7. In accordance with the display on the tester, read the Data List.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle Speed display/
    min.: 0 km/h (0 mph)
    max.: 255 km/h (158 mph)
    1. Vehicle stopped:
      0 km/h (0 mph)
    2. Same as speedometer reading
    -
    SPD (NT)
    Input Turbine Speed/
    display: 50 rpm
    min.: 0 rpm
    max.: 12750 rpm

    HINT:
    1. Lock-Up ON (After warming up engine):
      Input turbine speed (NT) equal to engine speed
    2. Lock-Up OFF (Idling at P or N position):
      Input turbine speed (NT) nearly equal to engine speed
    3. Vehicle stopped in D position: 0 rpm

    -
    Neutral Position SW Signal
    PNP SW Status/
    ON or OFF
    Shift lever position;
    P or N: ON
    Except P and N: OFF
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts,
    Click here.

    Stop Light Switch
    Stop Light SW Status/
    ON or OFF
    1. Brake pedal is depressed: ON
    2. Brake pedal is released: OFF
    -
    Shift Status
    ECM Gearshift Command/
    1st, 2nd, 3rd or 4th
    Shift lever position;
    1. L: 1st
    2. 2: 1st or 2nd
    3. 3: 1st, 2nd or 3rd
    4. D: 1st, 2nd, 3rd or 4th
    -
    Shift SW Status (R Range)
    PNP SW Status/
    ON or OFF
    Shift lever position;
    R: ON
    Except R: OFF
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts,
    Click here.

    Shift SW Status (P Range)
    PNP SW Status/
    ON or OFF
    Shift lever position;
    P: ON
    Except P: OFF
    Shift SW Status (N Range)
    PNP SW Status/
    ON or OFF
    Shift lever position;
    N: ON
    Except N: OFF
    Shift SW Status (D Range)
    PNP SW Status/
    ON or OFF
    Shift lever position;
    D or 3: ON
    Except D and 3: OFF
    Shift SW Status (3 Range)
    PNP SW Status/
    ON or OFF
    Shift lever position;
    3: ON
    Except 3: OFF
    -
    Shift SW Status (2 Range)
    PNP SW Status/
    ON or OFF
    Shift lever position;
    2: ON
    Except 2: OFF
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts,
    Click here.

    Shift SW Status (L Range)
    PNP SW Status/
    ON or OFF
    Shift lever position;
    L: ON
    Except L: OFF
    A/T Oil Temperature 1
    ATF (Automatic Transmission Fluid) Temperature Sensor Value/
    min.: -40°C (-40°F)
    max.: 215°C (419°F)
    1. After Stall Test; Approximately 80°C (176°F)
    2. Equal to ambient temperature when cold soak
    If value is -40°C (-40°F) or 150°C (302°F) or more, ATF temperature sensor circuit is open or short.
    Lock Up
    Lock Up Status/
    ON or OFF
    1. Lock Up: ON
    2. Except Lock Up: OFF
    -
    Lock Up Solenoid Status
    Lock Up Solenoid Status/
    ON or OFF
    1. Lock up solenoid ON: ON
    2. Lock up solenoid OFF: OFF
    -
    ST Solenoid Status
    Shift Solenoid ST Status/
    ON or OFF
    Up-shifting and down-shifting between 3rd and 4th gears while driving:
    OFF → ON → OFF
    -
    SLT Solenoid Status
    Shift Solenoid SLT Status/
    ON or OFF
    1. Accelerator pedal is depressed: OFF
    2. Accelerator pedal is released: ON
    -


ACTIVE TEST

HINT:
Performing the Active Test using the intelligent tester allows the relay, VSV, actuator and so on to operate without parts removal. Performing the Active Test as the first step of troubleshooting is one method to shorten labor time.
It is possible to display the Data List during the Active Test.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn on the tester.

  6. Select the following items: Powertrain / Engine and ECT / Active Test.

  7. In accordance with the display on the tester, perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the solenoid (SLT)*
    [Test Details]
    Operate shift solenoid SLT and raise line pressure.
    [Vehicle Condition]
    1. Vehicle stopped
    2. IDL: ON

    HINT:
    OFF: Line pressure up (when active test of "Control the Line Pressure Up" is performed, ECM turns off SLT solenoid)
    ON: No action (normal operation)

    ON or OFF
    -
    Activate the solenoid (S1)
    [Test Details]
    Operate shift solenoid S1
    [Vehicle Condition]
    1. Vehicle stopped
    2. Shift lever P or N position
    ON or OFF
    -
    Activate the solenoid (S2)
    [Test Details]
    Operate shift solenoid S2
    [Vehicle Condition]
    1. Vehicle stopped
    2. Shift lever P or N position
    ON or OFF
    -
    Activate the Lock Up
    [Test Details]
    Control shift solenoid SL to set automatic transaxle to lock-up condition.
    [Vehicle Condition]
    Vehicle Speed: 60 km/h (36 mph) or more, and 4th gear
    ON or OFF
    Possible to check SL operation.
    Control the Shift Position
    [Test Details]
    Operate shift solenoid valve and set each shift position.
    [Vehicle Condition]
    1. IDL: ON
    2. Less than 50 km/h (30 mph)
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of shift solenoid valves.
    Activate the Solenoid (ST)
    [Test Details]
    Operate shift solenoid ST
    [Vehicle Condition]
    1. Vehicle Stopped
    2. IDL: ON
    ON or OFF
    Possible to check ST operation.
    *: "Control the Line Pressure Up" in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transaxle, which is used in the HYDRAULIC TEST (Click here) as well.

    HINT:
    The pressure values in Active Test and HYDRAULIC TEST are different from each other.