AUTOMATIC TRANSAXLE SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn on the tester.
Select the following items: Powertrain / Engine and ECT / Data Test.
In accordance with the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle Speed display/ min.: 0 km/h (0 mph) max.: 255 km/h (158 mph) |
| - |
| SPD (NT) | Input Turbine Speed/ display: 50 rpm min.: 0 rpm max.: 12750 rpm |
| - |
| Neutral Position SW Signal | PNP SW Status/ ON or OFF | Shift lever position; P or N: ON Except P and N: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
|
| Stop Light Switch | Stop Light SW Status/ ON or OFF |
| - |
| Shift Status | ECM Gearshift Command/ 1st, 2nd, 3rd or 4th | Shift lever position;
| - |
| Shift SW Status (R Range) | PNP SW Status/ ON or OFF | Shift lever position; R: ON Except R: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
|
| Shift SW Status (P Range) | PNP SW Status/ ON or OFF | Shift lever position; P: ON Except P: OFF | |
| Shift SW Status (N Range) | PNP SW Status/ ON or OFF | Shift lever position; N: ON Except N: OFF | |
| Shift SW Status (D Range) | PNP SW Status/ ON or OFF | Shift lever position; D or 3: ON Except D and 3: OFF | |
| Shift SW Status (3 Range) | PNP SW Status/ ON or OFF | Shift lever position; 3: ON Except 3: OFF | - |
| Shift SW Status (2 Range) | PNP SW Status/ ON or OFF | Shift lever position; 2: ON Except 2: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
|
| Shift SW Status (L Range) | PNP SW Status/ ON or OFF | Shift lever position; L: ON Except L: OFF | |
| A/T Oil Temperature 1 | ATF (Automatic Transmission Fluid) Temperature Sensor Value/ min.: -40°C (-40°F) max.: 215°C (419°F) |
| If value is -40°C (-40°F) or 150°C (302°F) or more, ATF temperature sensor circuit is open or short. |
| Lock Up | Lock Up Status/ ON or OFF |
| - |
| Lock Up Solenoid Status | Lock Up Solenoid Status/ ON or OFF |
| - |
| ST Solenoid Status | Shift Solenoid ST Status/ ON or OFF | Up-shifting and down-shifting between 3rd and 4th gears while driving: OFF → ON → OFF | - |
| SLT Solenoid Status | Shift Solenoid SLT Status/ ON or OFF |
| - |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn on the tester.
Select the following items: Powertrain / Engine and ECT / Active Test.
In accordance with the display on the tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the solenoid (SLT)*
| [Test Details] Operate shift solenoid SLT and raise line pressure. [Vehicle Condition]
| ON or OFF | - |
| Activate the solenoid (S1) | [Test Details] Operate shift solenoid S1 [Vehicle Condition]
| ON or OFF | - |
| Activate the solenoid (S2) | [Test Details] Operate shift solenoid S2 [Vehicle Condition]
| ON or OFF | - |
| Activate the Lock Up | [Test Details] Control shift solenoid SL to set automatic transaxle to lock-up condition. [Vehicle Condition] Vehicle Speed: 60 km/h (36 mph) or more, and 4th gear | ON or OFF | Possible to check SL operation. |
| Control the Shift Position | [Test Details] Operate shift solenoid valve and set each shift position. [Vehicle Condition]
|
| Possible to check operation of shift solenoid valves. |
| Activate the Solenoid (ST) | [Test Details] Operate shift solenoid ST [Vehicle Condition]
| ON or OFF | Possible to check ST operation. |