Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING UNIT (for Sedan)

AIR CONDITIONING UNIT (for Sedan) > INSTALLATION

for Preparation Click here



1. INSTALL AIR CONDITIONING UNIT
  1. Install the air conditioning unit with the 3 screws.



2. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY
  1. Install the air conditioning amplifier with the screw.



3. INSTALL INSTRUMENT PANEL REINFORCEMENT
  1. Temporarily tighten the air conditioning unit with the 3 screws.

  1. Install the instrument panel reinforcement and the air conditioning unit with the 9 bolts.



  1. Install the 3 screws, 3 bolts and nut in the sequence shown in the illustration.


    I102592E02

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf } for screw A
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for nut
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for bolt

  1. Install the wire harness with the clamps and connect the connectors (for LHD).

  1. Install the wire harness with the clamps and connect the connectors (for RHD).

  1. Engage the clamps (for LHD).

  1. Engage the clamps (for RHD).

  1. Install the ground wire with the bolt.

    Torque:
    3.2 N*m{ 33 kgf*cm , 28 in.*lbf }



    I101179E01
  1. Install the drain hose into the position shown in the illustration.

    NOTICE:
    1. Install the drain hose with its UP mark facing upward, within the 90 degree range shown in the illustration.
    2. Install the drain hose without twisting it.



4. INSTALL CONNECTOR NO. 2 HOLDER
  1. Connect the connectors and install the connector No. 2 holder.

  1. Tighten the bolt.

    Torque:
    3.2 N*m{ 33 kgf*cm , 28 in.*lbf }



5. INSTALL MAIN BODY ECU (for LHD)
  1. Install the main body ECU with the 2 bolts.

    Torque:
    3.2 N*m{ 33 kgf*cm , 28 in.*lbf }

  1. Connect the 5 connectors and the 3 clamps.



6. INSTALL MAIN BODY ECU (for RHD)
  1. Install the main body ECU with the 2 bolts.

    Torque:
    3.2 N*m{ 33 kgf*cm , 28 in.*lbf }

  1. Connect the 5 connectors and the 5 clamps.



7. INSTALL INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for LHD)
  1. Install the instrument panel brace with the bolt, screw and nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for screw
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for nut
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for bolt

  1. Engage the clamp.



8. INSTALL INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for RHD)
  1. Install the instrument panel brace with the bolt, screw and nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for screw
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for nut
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for bolt

  1. Engage the 3 clamps.



9. INSTALL DEFROSTER NOZZLE ASSEMBLY
  1. Engage the 5 claws and install the defroster nozzle.

  1. Connect the 3 clamps and connector.



10. INSTALL HEATER TO REGISTER DUCT ASSEMBLY
  1. Engage the 3 claws and install the heater to register duct.



11. INSTALL STEERING COLUMN ASSEMBLY
(Click here)


12. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


13. CONNECT HEATER WATER INLET HOSE


    I101173E04
  1. Install the heater water inlet hose onto the heater unit.
    Text in Illustration 
    *a
    View A
    *b
    UP
    *c
    White Paint Mark

    NOTICE:
    Perform the installation with the hose clip and mark at the correct angle as shown in the illustration.



14. CONNECT HEATER WATER OUTLET HOSE


    I101172E04
  1. Install the heater water outlet hose onto the heater unit.
    Text in Illustration 
    *a
    View A
    *b
    UP
    *c
    Purple Paint Mark

    NOTICE:
    Perform the installation with the hose clip and mark at the correct angle as shown in the illustration.



15. INSTALL LIQUID TUBE SUB-ASSEMBLY
  1. Remove the vinyl tape from the liquid tube and the connecting portion of the unit.

  1. Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the connecting part of the liquid tube.

    Compressor oil:
    ND-OIL8 or the equivalent

  1. Install the O-ring onto the liquid tube.

  1. Connect the liquid tube to the unit.



16. INSTALL SUCTION TUBE SUB-ASSEMBLY
  1. Remove the vinyl tape from the suction tube and the connecting part of the unit.

  1. Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the connecting part of the suction tube.

    Compressor oil:
    ND-OIL8 or the equivalent

  1. Install the O-ring onto the suction tube.



    I101237
  1. Insert the tube joints securely into the fitting holes and tighten the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



17. ADD ENGINE COOLANT (for 1NZ-FE)
  1. Tighten all the plugs.

  1. Pour engine coolant into the radiator assembly until it overflows.

    Capacity:
    M/T 4.8 liters (5.1 USqts, 4.5 lmp. qts)
    A/T 4.7 liters (5.0 USqts, 4.4 lmp. qts)

    NOTICE:
    Do not substitute water for engine coolant.

    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.

  1. Install the radiator cap sub-assembly securely.

  1. Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Stop the engine and wait until the coolant cools down.

  1. If the engine coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the engine coolant level stays at the full level.

  1. Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add the engine coolant.

  1. Visually check for engine coolant leakage.



18. ADD ENGINE COOLANT (for 2NZ-FE)
  1. Tighten all the plugs.

  1. Pour engine coolant into the radiator assembly until it overflows.

    Capacity:
    w/o Fan Shroud Ventilation Duct: M/T 4.9 liters (5.2 USqts, 4.6 lmp. qts)
    w/o Fan Shroud Ventilation Duct: A/T 4.8 liters (5.1 USqts, 4.5 lmp. qts)
    w/ Fan Shroud Ventilation Duct: M/T 5.1 liters (5.4 USqts, 4.7 lmp. qts)
    w/ Fan Shroud Ventilation Duct: A/T 5.0 liters (5.3 USqts, 4.6 lmp. qts)

    NOTICE:
    Do not substitute water for engine coolant.

    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.

  1. Install the radiator cap sub-assembly securely.

  1. Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Stop the engine and wait until the coolant cools down.

  1. If the engine coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the engine coolant level stays at the full level.

  1. Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add the engine coolant.



19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



20. CHECK SRS WARNING LIGHT
(Click here)


21. CHARGE REFRIGERANT



I100449E02

NOTICE:
Charge refrigerant in accordance with the equipment manual.

  1. Perform vacuum purging using a vacuum pump.

  1. Charge refrigerant HFC-134a (R134a).

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    Standard:
    330 to 390 g (11.64 to 13.76 oz.) w/o Fan Shroud Ventilation Duct
    350 to 410 g (12.35 to 14.46 oz.) w/ Fan Shroud Ventilation Duct

    NOTICE:
    Do not start the engine before charging it with refrigerant as the cooler compressor doesn't work properly without sufficient refrigerant. This could cause the compressor to overheat.

    HINT:

    1. The relationship between the refrigerant charge amount and the pressure is as follows.


      I101544E02

    2. High Charge Range:
      If the refrigerant is overcharged, the pressure rises on the high-pressure side. High-pressure cut off frequently occurs. This causes insufficient cooling performance and also insufficient compressor lubrication.
    3. Low Charge Range:
      Shortage of refrigerant causes insufficient cooling performance and low circulation of refrigerant oil, which shortens the compressor life. Operation with insufficient coolant raises the refrigerant temperature and causes heat deterioration of the rubber seals and hoses. Cracking and thus refrigerant leakage may occur.


    1. Install the caps onto the service valves on the refrigerant line.



22. WARM UP ENGINE

NOTICE:
Warm up the engine at less than 2000 rpm for 1 minute or more after charging it with refrigerant.



23. INSPECT FOR COOLANT LEAK (for 1NZ-FE)

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.



    A106594
  1. Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.



24. INSPECT FOR COOLANT LEAK (for 2NZ-FE)

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.



    A106594
  1. Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.



25. INSPECT FOR REFRIGERANT LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation as follows:

    1. Stop the engine.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system.
      When the compressor is off: approximately 392 to 588 kPa (4 to 6 kgf*cm2, 57 to 85 psi)

    HINT:
    It is impossible for the above pressure to be maintained if there is leakage.



    I101569E02
  1. Using the halogen leak detector, check the refrigerant line, especially at the connection points, for leakage.



    I100587E02
  1. Bring the halogen leak detector close to the drain hose before performing the test.

    HINT:
    1. After the blower motor has stopped, leave the cooling unit for at least 15 minutes.
    2. Place the halogen leak detector sensor under the drain hose.
    3. When bringing the halogen leak detector close to the drain hose, make sure that the halogen leak detector does not react to the volatile gases.

    If such a reaction is unavoidable, the vehicle must be lifted up.

  1. If no gas leakage is detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.



26. POSITION FRONT WHEELS FACING STRAIGHT AHEAD


27. PERFORM CALIBRATION OF TORQUE SENSOR ZERO POINT
(Click here)