VEHICLE STABILITY CONTROL SYSTEM > Brake Warning Light Remains ON |

| 1.CHECK CAN COMMUNICATION SYSTEM |
Check if CAN communication system DTCs are output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED |
Check if the skid control ECU connector is securely connected.
|
| ||||
| OK | |
| 3.INSPECT BATTERY |
Check the battery voltage.
|
| ||||
| OK | |
| 4.INSPECT SKID CONTROL ECU (IG1 TERMINAL) |
Disconnect the A31 skid control ECU connector.
Turn the ignition switch to ON.
![]() |
Measure the voltage according to the value(s) in the table below.
| *1 | Front view of wire harness connector (to Skid Control ECU) |
| Tester Connection | Switch Condition | Specified Condition |
| A31-34 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 5.INSPECT SKID CONTROL ECU (GND TERMINAL) |
Turn the ignition switch off.
![]() |
Measure the resistance according to the value(s) in the table below.
| *1 | Front view of wire harness connector (to Skid Control ECU) |
| Tester Connection | Condition | Specified Condition |
| A31-1 (GND1) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH) |
Reconnect the skid control ECU connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Parking Brake SW | Parking brake switch / ON or OFF | ON: Parking brake applied OFF: Parking brake released | - |
Using the intelligent tester, check the input of the switch operation when the parking brake pedal is operated.
|
| ||||
| OK | |
| 7.INSPECT BRAKE FLUID LEVEL WARNING SWITCH |
![]() |
Turn the ignition switch off.
| *1 | Component without harness connected (Brake Fluid Level Warning Switch) |
Remove the reservoir filler cap and strainer.
Disconnect the brake fluid level warning switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 2 | Switch OFF (Float up) | 10 kΩ or higher |
| 1 - 2 | Switch ON (Float down) | Below 1 Ω |
| Result | Proceed to |
| OK | A |
| NG (for Sedan) | B |
| NG (for Hatchback) | C |
|
| ||||
|
| ||||
| A | |
| 8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH) |
Disconnect the D84 or D87 combination meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D84-2 (SW) - A10-1 | Always | Below 1 Ω |
| D84-2 (SW) - Body ground | Always | 10 kΩ or higher |
| A10-2 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| D87-7 (SW) - A10-1 | Always | Below 1 Ω |
| D87-7 (SW) - Body ground | Always | 10 kΩ or higher |
| A10-2 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 9.INSPECT COMBINATION METER ASSEMBLY |
Connect the intelligent tester to the DLC3.
Perform Active Test of the combination meter using the intelligent tester.
| Result | Proceed to |
| OK (for Sedan) | A |
| OK (for Hatchback) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 10.REPLACE COMBINATION METER ASSEMBLY |
Turn the ignition switch off.
Replace the combination meter.
| NEXT | |
| 11.INSPECT COMBINATION METER ASSEMBLY |
Connect the intelligent tester to the DLC3.
Perform Active Test of the combination meter using the intelligent tester.
| Result | Proceed to |
| OK | A |
| NG (for Sedan) | B |
| NG (for Hatchback) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 12.INSPECT PARKING BRAKE SWITCH |
![]() |
Turn the ignition switch off.
| *1 | Component without harness connected (Parking Brake Switch) |
Disconnect the parking brake switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - Body ground | Parking brake switch ON (Switch pin free) | Below 1 Ω |
| 1 - Body ground | Parking brake switch OFF (Switch pin pushed in) | 10 kΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for Sedan) | B |
| NG (for Hatchback) | C |
|
| ||||
|
| ||||
| A | |
| 13.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARKING BRAKE SWITCH) |
Disconnect the 4C main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 4C-2 (PKB) - D87-1 | Always | Below 1 Ω |
| 4C-2 (PKB) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
| OK (for Sedan) | A |
| OK (for Hatchback) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||