Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > DIAGNOSIS SYSTEM

for Preparation Click here



BUS CHECK (COMMUNICATION MALFUNCTION ECU)

HINT:
Only CAN communication system DTCs for each ECU can be displayed on the intelligent tester.



    C128170
  1. Select "Bus Check" from the "System Select" screen on the intelligent tester.



  2. C128171
  3. Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".



  4. C128172
  5. Select the system of the DTC to be checked and select "Details".



  6. C128173
  7. CAN communication system DTCs are displayed.


BUS CHECK (COMMUNICATION BUS CHECK)

HINT:
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the intelligent tester.



    C128171
  1. Select "Communication Bus Check" from the "Bus Check" screen.



  2. C197126
  3. The screen displays the ECUs and sensors that are properly connected to the CAN communication system.

    HINT:
    1. If any properly connected ECUs or sensors are not displayed, there is a communication stop in the system (Click here).

    2. C197127
      The default item displayed in the combo box is "ALL". When checking the ECUs (sensors) connected to each bus, pull down the combo box and select the bus to be checked from the drop down list. The drop down list displays "ALL", "V Bus", and the names of the remaining buses.
      Combo Box
      Display Content
      ALL
      All ECUs (sensors) connected to the CAN bus
      V Bus
      ECUs (sensors) connected to the V bus
      Bus Name
      ECUs (sensors) connected to the selected bus
    3. The connection status (shown below) is indicated by the background color displayed behind the system name.
      ECU (Sensor) on V Bus
      Background Color
      Connection Status
      White
      Detected normally
      Yellow
      Could not be detected in the past, but is currently detected
      Red
      Detected in the past, but cannot be detected now
      Not displayed
      Has never been detected
      ECU (Sensor) with no Data Monitor History
      Background Color
      Connection Status
      White
      Detected normally
      Yellow
      Could not be detected in the past, but is currently detected
      Red
      Detected in the past, but cannot be detected now
      Not displayed
      Has never been detected
      ECU (Sensor) with no Data Monitor History
      Background Color
      Connection Status
      White
      Detected normally
      Yellow
      Could not be detected in the past, but is currently detected
      Red
      Detected in the past, but cannot be detected now
      Red
      Has never been detected bus has connection history
      Not displayed
      Has never been detected and has no connection history



  4. C128179
  5. "There is no system connected to the communication bus" is displayed if there are no ECUs or sensors connected to the CAN bus.


CHECK INSTALLED SYSTEMS (ECUS and SENSORS) THAT ADOPT CAN COMMUNICATION
  1. Systems (ECUs and sensors) that adopt CAN communication vary depending on the vehicle's optional settings. Check which systems (ECUs and sensors) are installed on the vehicle.

    ECU/Sensor Name
    Check Method
    Brake actuator (skid control ECU)
    Vehicle with ABS
    Air conditioning amplifier
    With air conditioning
    Power steering ECU
    Installed on all vehicles
    ABS and traction actuator (Skid control ECU)
    Vehicle with VSC
    ECM
    Installed on all vehicles
    Main body ECU
    Installed on all vehicles
    Combination meter ECU
    Installed on all vehicles
    Steering sensor
    Vehicle with VSC
    Yaw rate sensor
    Vehicle with VSC
    Center airbag sensor assembly
    Installed on all vehicles


DTC TABLE BY ECU

HINT:
  1. In the CAN communication system, CAN communication system DTCs output by the ECU can be displayed by using the intelligent tester.
  2. If CAN communication system DTCs are output, trouble cannot be determined solely from the DTCs. Perform troubleshooting according to "How to Proceed With Troubleshooting" (Click here).

  1. BRAKE ACTUATOR (SKID CONTROL ECU)
    For vehicle with ABS only

    HINT:
    DTC communication uses the CAN communication system.

    DTC No.
    Detection Item
    U0073
    Control Module Communication Bus OFF

  2. ABS AND TRACTION ACTUATOR (SKID CONTROL ECU)

    HINT:
    DTC communication uses the CAN communication system.


    DTC No.
    Detection Item
    U0073
    Control Module Communication Bus OFF
    U0100
    Lost Communication with ECM/PCM
    U0123
    Lost Communication with Yaw Rate Sensor Module
    U0124
    Lost Communication with Lateral Acceleration Sensor Module
    U0126
    Lost Communication with Steering Angle Sensor Module

  3. POWER STEERING ECU

    HINT:
    DTC communication uses the SIL line.

    DTC No.
    Detection Item
    U0100
    Lost Communication with ECM/PCM "A"
    U0129*
    Lost Communication with Brake System Control Module
    1. *: w/ ABS

  4. COMBINATION METER ECU

    HINT:
    DTC communication uses the CAN communication system.

    DTC No.
    Detection Item
    U0100*1
    Lost Communication with ECM/PCM "A"
    U0129*2
    Lost Communication with Brake System Control Module

    HINT:
    1. *1: DTC U0100 is stored if communication cannot be established with the ECM at a vehicle speed of 5 km/h (3.2 mph) or more.
    2. *2: DTC U0129 is stored if communication cannot be established with the brake actuator (skid control ECU) during engine start.

    NOTICE:
    These DTCs may not be stored when the ignition switch is turned on (IG) or when the engine stops.

  5. AIR CONDITIONING AMPLIFIER
    For vehicle with air conditioning

    HINT:
    DTC communication uses the CAN communication system.

    DTC No.
    Detection Item
    B1499/99
    Multiplex Communication Circuit

  6. ECM

    HINT:
    1. The ECM is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "Engine" is not displayed on the "Communication Bus Check " screen on the intelligent tester, proceed to "ECM Communication Stop Mode" (Click here).

  7. MAIN BODY ECU

    HINT:
    1. The main body ECU is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "Integrated J/B" is not displayed on the "Communication Bus Check" screen on the intelligent tester, proceed to "Main Body ECU Communication Stop Mode." (Click here)

  8. STEERING SENSOR

    HINT:
    1. The steering sensor is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "Steering Angle Sensor" is not displayed on the "Communication Bus Check" screen on the intelligent tester, proceed to "Steering Angle Sensor Communication Stop Mode." (Click here)

  9. YAW RATE SENSOR

    HINT:
    1. The yaw rate sensor is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "Yaw Rate/Deceleration Sensor" is not displayed on the "Communication Bus Check" screen on the intelligent tester, proceed to "Yaw Rate Sensor Communication Stop Mode." (Click here)


DTC COMBINATION TABLE
*1: This DTC may not be output when the CAN communication system malfunctions.
*2: Only output during the trip in which malfunction is detected.
*3: Only stored while malfunction continues.
*4: This DTC is output when communication failures from the ECM and the combination meter ECU occur.
*5: w/ VSC
*6: w/ ABS
*1: This DTC may not be output when the CAN communication system malfunctions.
*4: This DTC is output when communication failures from the ECM and the combination meter ECU occur.
*5: w/ VSC
*6: w/ ABS

DTC
Trouble Mode
Output from
Output DTC
ECM Communication Stop Mode
Brake Actuator (Skid Control ECU) Communication Stop Mode
ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode
Steering Angle Sensor Communication Stop Mode
Yaw Rate Sensor Communication Stop Mode
ABS and Traction Actuator (Skid Control ECU)
U0073*5
X
X
○*1, *2
X
X
U0100*5
○*3
X
○*1, *3
X
X
U0123*5
X
X
○*1, *2
X
○*2
U0124*5
X
X
○*1, *2
X
○*2
U0126*5
X
X
○*1, *2
○*2
X
Brake Actuator (Skid Control ECU)
U0073*6
X
○*1, *3
X
X
X
Power Steering ECU
U0100
○
X
X
X
X
U0129*6
X
○
○
X
X
Combination Meter ECU
U0100
○
X
X
X
X
U0129*6
X
○
○
X
X

HINT:
  1. ○: It is necessary to check for the trouble mode.
  2. X: DTC is output possibility when open in one side of CAN wire.


DTC
Trouble Mode
Output from
Output DTC
Power Steering ECU Communication Stop Mode
Center Airbag Sensor Communication Stop Mode
Air Conditioning Amplifier Communication Stop Mode
Combination Meter ECU Communication Stop Mode
Main Body ECU Communication Stop Mode
ABS and Traction Actuator (Skid Control ECU)
U0073*5
X
X
X
X
X
U0100*5
X
X
X
X
X
U0123*5
X
X
X
X
X
U0124*5
X
X
X
X
X
U0126*5
X
X
X
X
X
Brake Actuator (Skid Control ECU)
U0073*6
X
X
X
X
X
Power Steering ECU
U0100
○*1
X
X
X
X
U0129*6
○*1
X
X
X
X
Combination Meter ECU
U0100
X
X
X
○*1
X
U0129*6
X
X
X
○*1
X

HINT:
  1. ○: It is necessary to check for the trouble mode.
  2. X: DTC is output possibility when open in one side of CAN wire.

  1. Perform troubleshooting according to the combination of DTCs output.

    1. Brake Actuator (Skid Control ECU) Communication Stop Mode: (Click here)
    2. Air Conditioning Amplifier Communication Stop Mode: (Click here)
    3. Power Steering ECU Communication Stop Mode: (Click here)
    4. ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode: (Click here)
    5. ECM Communication Stop Mode: (Click here)
    6. Main Body ECU Communication Stop Mode: (Click here)
    7. Combination Meter ECU Communication Stop Mode: (Click here)
    8. Steering Angle Sensor Communication Stop Mode: (Click here)
    9. Yaw Rate Sensor Communication Stop Mode: (Click here)
    10. Center Airbag Sensor Communication Stop Mode: (Click here)