REAR AXLE BEAM (for Sedan) > INSTALLATION |
| 1. TEMPORARILY TIGHTEN REAR AXLE BEAM |
![]() |
Support the rear axle beam with a jack.
Install the axle beam onto the vehicle and provisionally tighten the 2 bolts.
| 2. INSTALL REAR COIL SPRING LH |
Install the coil spring insulator lower onto the axle beam.
![]() |
Install the coil spring insulator upper so that its gap fits onto the end of coil spring.
![]() |
Install the coil spring onto the axle beam.
| 3. INSTALL REAR COIL SPRING RH |
| 4. TEMPORARILY TIGHTEN REAR SHOCK ABSORBER LH |
Support the axle beam with a jack. Insert a wooden block between the jack and the rear axle spring seat to prevent damage.
Jack up the axle beam slowly, and provisionally install the shock absorber (lower side) with the bolt and nut onto the axle beam.
Install the suspension support and cushion retainer.
![]() |
While holding the piston rod, install a new nut (lower nut) to the specified standard.
Hold the lower nut and tighten the upper nut against it.
| 5. TEMPORARILY TIGHTEN REAR SHOCK ABSORBER RH |
| 6. INSTALL REAR SHOCK ABSORBER CAP LH |
| 7. INSTALL REAR SHOCK ABSORBER CAP RH |
| 8. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH |
![]() |
Install the axle hub and bearing onto the axle beam with the 4 bolts.
| 9. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH |
| 10. INSPECT REAR AXLE HUB BEARING |
Remove the rear wheel.
Remove the rear brake drum .
![]() |
Inspect the axle hub and bearing backlash.
Using a dial indicator, check the backlash near the center of the axle hub.
![]() |
Inspect the axle hub and bearing runout.
Using a dial indicator, check the runout of the surface of the axle hub.
Install the rear brake drum.
Adjust the rear drum brake shoe clearance .
Install the rear wheel.
| 11. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY |
| 12. ADJUST REAR DRUM BRAKE SHOE CLEARANCE |
![]() |
Provisionally install the 2 hub nuts.
Remove the hole plug, and turn the adjuster to expand the shoe until the drum locks.
Using a screwdriver, release the adjuster 12 notches.
Install the hole plug.
| 13. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY |
![]() |
Install the parking brake cable with the bolt and a new clamp.
| 14. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY |
| 15. INSTALL REAR NO. 4 BRAKE TUBE |
![]() |
Install the brake tube onto the axle beam with the nut.
Connect the flexible hose to the axle beam with a new clip.
Using SST, install the brake tube onto the flexible hose.
| 16. INSTALL REAR NO. 3 BRAKE TUBE |
| 17. INSTALL SKID CONTROL SENSOR WIRE (w/ ABS) |
![]() |
Install the skid control sensor wire onto the axle beam with the nut.
![]() |
Connect the skid control sensor wire connector.
| 18. INSTALL REAR WHEEL |
| 19. STABILIZE SUSPENSION |
Lower the vehicle from the jack.
Bounce the vehicle up and down several times to stabilize the suspension.
| 20. FULLY TIGHTEN REAR AXLE BEAM |
![]() |
Suspend the jack on the rear axle spring seat and adjust the length of the shock absorber to the reference value.
Fully tighten the 2 bolts.
| 21. FULLY TIGHTEN REAR SHOCK ABSORBER LH |
Fully tighten the shock absorber (lower side) with the bolt.
| 22. FULLY TIGHTEN REAR SHOCK ABSORBER RH |
| 23. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type) |
![]() |
Engage the 3 hooks and install the rear seatback.
Tighten the 3 bolts.
![]() |
Install the rear seat outer belt into the rear seat shoulder belt guide.
for 3 Point Type Rear Center Seat belt:
Install the rear center seat outer belt into the rear center seat shoulder belt guide.
| 24. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type) |
![]() |
Pass the rear seat inner belt through the rear seat cushion cover pad slit.
Engage the 3 hooks and install the rear seat cushion cover pad.
| 25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 26. FILL RESERVOIR WITH BRAKE FLUID |
![]() |
Remove the cowl top No. 2 ventilator louver center.
![]() |
Set the brake fluid can upside down on the reservoir.
| 27. BLEED MASTER CYLINDER |
![]() |
Using a union nut wrench (10 mm), disconnect the brake tubes from the master cylinder.
![]() |
Slowly depress the brake pedal and hold it there (Step A).
![]() |
Block the outer holes with your fingers, and release the brake pedal (Step B).
Repeat steps A and B 3 or 4 times.
![]() |
Using a union nut wrench (10 mm), connect the brake tubes to the master cylinder.
| 28. BLEED BRAKE LINE |
![]() |
Connect the vinyl tube to the bleeder plug.
Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).
At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).
Repeat steps C and D until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
Repeat the above procedure to bleed the air out of the brake line for each wheel.
| 29. CHECK FLUID LEVEL IN RESERVOIR |
Check the fluid level and add fluid if necessary.
| 30. INSPECT FOR BRAKE FLUID LEAK |
| 31. INSPECT REAR WHEEL ALIGNMENT |
Inspect the rear wheel alignment (Click here).
| 32. CHECK ABS SENSOR SIGNAL (w/o VSC) |
Check the ABS sensor signal (Click here).
| 33. CHECK ABS SENSOR SIGNAL (w/ VSC) |
Check the ABS sensor signal (Click here).