MANUAL TRANSAXLE ASSEMBLY (for Hatchback) > INSTALLATION |
| 1. INSTALL MANUAL TRANSAXLE ASSEMBLY |
![]() |
Align the input shaft with the clutch disc and install the manual transaxle onto the engine.
Install the 7 bolts.
| 2. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET |
![]() |
Install the engine mounting bracket LH with the 4 bolts.
| 3. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR |
![]() |
Install the engine mounting insulator LH with the 5 bolts.
Install the engine mounting bracket LH and engine insulator LH with the bolt and nut.
| 4. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING CONTROL BRACKET |
![]() |
Install the engine mounting control bracket with the 4 bolts.
| 5. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
Support the front suspension crossmember with a transmission jack.
![]() |
Provisionally install the front suspension crossmember onto the body with the 6 bolts.
| *1 | Bolt A |
| *2 | Bolt B |
| *3 | Bolt C |
| *a | Front Side |
| Bolt | Underhead Length (mm) |
| A | 38 |
| B | 99 |
| C | 41 |
By inserting SST into the datum holes in the front suspension crossmembers RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.

| *1 | Bolt A | *2 | Bolt B |
| *3 | Bolt C | *4 | for Bolt B with Bolt Strength Class 11T |
| *5 | for Bolt B with Bolt Strength Class 10T | - | - |
| *a | Front Side | *b | Datum Hole |
| *c | OK | *d | NG |
Install the engine moving control rod with the bolt.
| 6. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH |
for Automatic Transaxle:
Coat the spline of the inboard joint with ATF.
for Manual Transaxle:
Coat the spline of the inboard joint with gear oil.
![]() |
Align the inboard joint splines and install the drive shaft with a screwdriver and hammer.
| 7. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH |
| 8. INSTALL FRONT AXLE ASSEMBLY LH |
Push the front axle out of the vehicle to align the spline of the drive shaft with the front axle and insert the front axle.
| 9. INSTALL FRONT AXLE ASSEMBLY RH |
| 10. INSTALL FRONT STABILIZER LINK ASSEMBLY LH |
![]() |
Install the stabilizer link with the nut.
| 11. INSTALL FRONT STABILIZER LINK ASSEMBLY RH |
| 12. INSTALL TIE ROD END SUB-ASSEMBLY LH |
![]() |
Install the tie rod end onto the steering knuckle with a new castle nut.
Install a new cotter pin.
| 13. INSTALL TIE ROD END SUB-ASSEMBLY RH |
| 14. INSTALL FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 LH |
![]() |
Install the lower arm onto the steering knuckle with a new castle nut.
Install a new clip.
| 15. INSTALL FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 RH |
| 16. INSTALL SPEED SENSOR FRONT LH (w/ ABS) |
![]() |
Install the speed sensor onto the steering knuckle with the bolt.
![]() |
Install the flexible hose and speed sensor with the bolt.
| 17. INSTALL SPEED SENSOR FRONT RH (w/ ABS) |
| 18. INSTALL FRONT AXLE SHAFT LH NUT |
![]() |
Using a 30 mm socket wrench, install a new axle hub nut.
Using a chisel and hammer, stake the axle hub nut.
| 19. INSTALL FRONT AXLE SHAFT RH NUT |
| 20. INSTALL STARTER ASSEMBLY |
![]() |
Install the starter assembly with the 2 bolts.
Connect the connector.
Connect terminal 30 with the nut.
Close the terminal cap.
| 21. CONNECT CONNECTOR |
Connect the back-up light switch connector.
| 22. CONNECT WIRE HARNESS |
![]() |
Connect the wire harness with the bolt.
| 23. INSTALL CONTROL CABLE BRACKET |
![]() |
Install the control cable bracket with the 2 bolts.
| 24. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Connect the 2 cable ends and install the 2 washers and the 2 clips.
Install 2 new clips onto the control cable bracket.
| 25. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY |
![]() |
Install the clutch release cylinder and clutch pipe with the 4 bolts.
| 26. INSTALL BATTERY CARRIER |
![]() |
Install the battery carrier with the 5 bolts.
| 27. INSTALL BATTERY TRAY |
| 28. INSTALL BATTERY |
| 29. INSTALL BATTERY CLAMP SUB-ASSEMBLY |
| 30. INSTALL AIR CLEANER BRACKET |
![]() |
Install the air cleaner bracket with the 2 bolts.
| 31. INSTALL AIR CLEANER ASSEMBLY |
![]() |
Install the air cleaner case with air cleaner inlet No. 1 with the 2 bolts.
Connect the wire harness to the air cleaner case.
Install the air cleaner element.
![]() |
Install and lock the air cleaner cap and air cleaner hose and then tighten the air cleaner hose clamp.
Connect the ventilation hose to the air cleaner hose.
Connect the vacuum switching valve connector and wire harness clamp.
Connect the fuel vapor feed hose and fuel vapor feed hose No. 1 to the vacuum switching valve assembly.
Connect the intake air flow meter connector and wire harness clamp.
| 32. INSTALL CYLINDER HEAD COVER NO.2 |
![]() |
Tighten 2 A nuts, then 2 B nuts.
| 33. INSTALL COWL TOP PANEL OUTER |
![]() |
Install the cowl top panel with the 9 bolts.
![]() |
Connect the wire harness clamp.
| 34. INSTALL COWL TO REGISTER DUCT SUB-ASSEMBLY NO.2 |
![]() |
Engage the claw to install cowl to register duct No. 2.
| 35. INSTALL WINDSHIELD WIPER MOTOR AND LINK |
![]() |
Connect the connector.
Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
Install the front wiper motor and link with the 2 bolts.
| 36. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD) |
![]() |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the 2 clips.
| 37. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD) |
![]() |
Connect the washer hose.
![]() |
Engage the 11 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
![]() |
Engage the 2 hooks and install cowl top ventilator louver center No. 1.
| 38. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD) |
![]() |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the clip.
| 39. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD) |
![]() |
Engage the 10 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
| 40. INSTALL HOOD TO COWL TOP SEAL |
![]() |
Engage the 7 clips and install the hood to cowl top seal.
| 41. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 42. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 43. INSTALL HOOD SUB-ASSEMBLY |
| 44. INSPECT HOOD SUB-ASSEMBLY |
Check that the clearance measurements are within the standard ranges.

| Area | Measurement | Area | Measurement |
| A | 1.7 to 5.7 mm (0.067 to 0.224 in.) | G | -1.55 to 2.45 mm (-0.061 to 0.096 in.) |
| B | -2 to 2 mm (-0.079 to 0.079 in.) | H | 1.75 to 5.75 mm (0.067 to 0.226 in.) |
| C | 4.45 to 10.45 mm (0.175 to 0.411 in.) | I | -1.25 to 2.75 mm (-0.049 to 0.108 in.) |
| D | -0.95 to 5.05 mm (-0.037 to 0.199 in.) | J | -1.5 to 1.5 mm (-0.059 to 0.059 in.) |
| E | 7.55 to 13.55 mm (0.297 to 0.533 in.) | K | 2.0 to 5.0 mm (0.079 to 0.197 in.) |
| F | 1.65 to 5.65 mm (0.065 to 0.222 in.) | - | - |
| 45. ADJUST HOOD SUB-ASSEMBLY |
![]() |
Loosen the hood side hinge bolts.
Move the hood to adjust the clearance to within the standard range.
Tighten the hood side hinge bolts after the adjustment.
![]() |
Adjust the height of the hood front end by turning the cushion rubber.
![]() |
Adjust the hood lock.
Loosen the 3 bolts.
Adjust the hood lock position so that the striker can enter it smoothly.
Tighten the 3 bolts after the adjustment.
| 46. ADD TRANSAXLE OIL |
| 47. INSPECT AND ADJUST TRANSAXLE OIL |
![]() |
Stop the vehicle in a level place.
Remove the transmission filler plug and the gasket.
Check that the oil surface is within 5 mm (0.20 in.) of the bottom of the transmission filler plug opening.
Check for oil leakage when the oil level is low.
Install the transmission filler plug and a new gasket.
| 48. INSTALL ENGINE UNDER COVER RH |
| 49. INSTALL ENGINE UNDER COVER LH |
| 50. INSTALL FRONT WHEELS |
| 51. INSTALL STEERING SLIDE YOKE SUB-ASSEMBLY |
![]() |
Align the matchmarks and install the sliding yoke onto the intermediate shaft with bolt B.
| *1 | Bolt A |
| *2 | Bolt B |
| *a | Matchmark |
Tighten bolt A.
| 52. INSTALL COLUMN HOLE COVER SILENCER SHEET |
Install the column hole cover silencer sheet with the 2 clips.
Install the floor carpet.
| 53. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 54. INSPECT ABS SPEED SENSOR SIGNAL |
| 55. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |
| 56. CHECK FOR EXHAUST GAS LEAKAGE |
| 57. CHECK FOR TRANSAXLE OIL LEAKAGE |