Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1820/55    Short in Front Driver Side - Side Squib Circuit

DTC    B1821/55    Open in Front Driver Side - Side Squib Circuit

DTC    B1822/55    Short to GND in Front Driver Side - Side Squib Circuit

DTC    B1823/55    Short to B+ in Front Driver Side - Side Squib Circuit

for Preparation Click here


DESCRIPTION

The driver side - side squib circuit consists of the center airbag sensor assembly and the driver side front seat side airbag assembly.
This circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side - side squib circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1820/55
  1. Center airbag sensor assembly detects line short circuit signal in driver side - side squib circuit 5 times during primary check.
  2. Driver side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat side airbag assembly LH (Driver side - side squib) (LHD)
  3. Front seat side airbag assembly RH (Driver side - side squib) (RHD)
  4. Center airbag sensor assembly
B1821/55
  1. Center airbag sensor assembly detects open circuit signal in driver side - side squib circuit for 2 seconds.
  2. Driver side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat side airbag assembly LH (Driver side - side squib) (LHD)
  3. Front seat side airbag assembly RH (Driver side - side squib) (RHD)
  4. Center airbag sensor assembly
B1822/55
  1. Center airbag sensor assembly detects short circuit to ground signal in driver side - side squib circuit for 0.5 seconds.
  2. Driver side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat side airbag assembly LH (Driver side - side squib) (LHD)
  3. Front seat side airbag assembly RH (Driver side - side squib) (RHD)
  4. Center airbag sensor assembly
B1823/55
  1. Center airbag sensor assembly detects short circuit to B+ signal in driver side - side squib circuit for 0.5 seconds.
  2. Driver side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat side airbag assembly LH (Driver side - side squib) (LHD)
  3. Front seat side airbag assembly RH (Driver side - side squib) (RHD)
  4. Center airbag sensor assembly

WIRING DIAGRAM


H102293E01


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting CHECK MODE (signal check) with the intelligent tester (Click here).
  2. After selecting CHECK MODE (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).

1.CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY (DRIVER SIDE - SIDE SQUIB)
H100168E02
SST
09843-18060  
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the driver side front seat side airbag assembly.

  1. Connect the black wire side of SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect a tester to the front seat side airbag assembly (driver side - side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert the SST straight into the terminals of the connector.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1820, B1821, B1822, B1823 and 55 are not output.

    HINT:
    DTCs other than DTC B1820, B1821, B1822, B1823 and 55 may be output at this time, but they are not related to this check.



OK
REPLACE FRONT SEAT ASSEMBLY LH (LHD)

OK
REPLACE FRONT SEAT ASSEMBLY RH (RHD)
NG


2.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST from connector C.

  1. Check that the floor wire connectors (on the driver side front seat side airbag assembly side) are not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE
OK


3.CHECK FLOOR WIRE (DRIVER SIDE - SIDE SQUIB CIRCUIT)
H100112E02
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST from connector C.

  1. Disconnect the connectors from the center airbag sensor assembly.

  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage.

      Standard Voltage:
      Tester connection
      Condition
      Specified condition
      Y1-1 (SFL-) - Body ground (*1)
      Ignition switch ON
      Below 1 V
      Y1-2 (SFL+) - Body ground (*1)
      Ignition switch ON
      Below 1 V
      X1-1 (SFR-) - Body ground (*2)
      Ignition switch ON
      Below 1 V
      X1-2 (SFR+) - Body ground (*2)
      Ignition switch ON
      Below 1 V

      *1: LHD
      *2: RHD

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance.

      Standard Resistance:
      Tester connection
      Condition
      Specified condition
      Y1-1 (SFL-) - Y1-2 (SFL+) (*1)
      Always
      Below 1 Ω
      X1-1 (SFR-) - X1-2 (SFL+) (*2)
      Always
      Below 1 Ω

      *1: LHD
      *2: RHD

  1. Check for short to ground in the circuit.

    1. Measure the resistance.

      Standard Resistance:
      Tester connection
      Condition
      Specified condition
      Y1-1 (SFL-) - Body ground (*1)
      Always
      1 MΩ or higher
      Y1-2 (SFL+) Body ground (*1)
      Always
      1 MΩ or higher
      X1-1 (SFR-) - Body ground (*2)
      Always
      1 MΩ or higher
      X1-2 (SFR+) - Body ground (*2)
      Always
      1 MΩ or higher

      *1: LHD
      *2: RHD

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance.

      Standard Resistance:
      Tester connection
      Condition
      Specified condition
      Y1-1 (SFL-) - Y1-2 (SFL+) (*1)
      Always
      1 MΩ or higher
      X1-1 (SFR-) - X1-2 (SFL+) (*2)
      Always
      1 MΩ or higher

      *1: LHD
      *2: RHD



NG
REPAIR OR REPLACE FLOOR WIRE
OK


4.CHECK CENTER AIRBAG SENSOR ASSEMBLY
H100873E01
  1. Connect the connectors to the driver side front seat side airbag assembly and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1820, B1821, B1822, B1823 and 55 are not output.

    HINT:
    DTCs other than DTC B1820, B1821, B1822, B1823 and 55 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK