DTC B1825/56 Short in Front Passenger Side - Side Squib Circuit |
DTC B1826/56 Open in Front Passenger Side - Side Squib Circuit |
DTC B1827/56 Short to GND in Front Passenger Side - Side Squib Circuit |
DTC B1828/56 Short to B+ in Front Passenger Side - Side Squib Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1825/56 |
|
|
| B1826/56 |
|
|
| B1827/56 |
|
|
| B1828/56 |
|
|

| 1.CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY (FRONT PASSENGER SIDE - SIDE SQUIB) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connector from the front seat side airbag assembly (front passenger side).
Connect the black wire side of SST (resistance 2.1 Ω) to connector C.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
|
| ||||
| NG | |
| 2.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST from connector C.
Check that the floor wire connectors (on the front passenger side front seat side airbag assembly side) are not damaged.
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE (FRONT PASSENGER SIDE - SIDE SQUIB CIRCUIT) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST from connector C.
Disconnect the connectors from the center airbag sensor assembly.
Check for short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage.
| Tester connection | Condition | Specified condition |
| X1-1 (SFR-) - Body ground (*1) | Ignition switch ON | Below 1 V |
| X1-2 (SFR+) - Body ground (*1) | Ignition switch ON | Below 1 V |
| Y1-1 (SFL-) - Body ground (*2) | Ignition switch ON | Below 1 V |
| Y1-2 (SFL+) - Body ground (*2) | Ignition switch ON | Below 1 V |
Check for open in the circuit.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester connection | Condition | Specified condition |
| X1-1 (SFR-) - X1-2 (SFR+) (*1) | Always | Below 1 Ω |
| Y1-1 (SFL-) - Y1-2 (SFL+) (*2) | Always | Below 1 Ω |
Check for short to ground in the circuit.
Measure the resistance.
| Tester connection | Condition | Specified condition |
| X1-1 (SFR-) - Body ground (*1) | Always | 1 MΩ or higher |
| X1-2 (SFR+) Body ground (*1) | Always | 1 MΩ or higher |
| Y1-1 (SFL-) - Body ground (*2) | Always | 1 MΩ or higher |
| Y1-2 (SFL+) - Body ground (*2) | Always | 1 MΩ or higher |
Check for short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance.
| Tester connection | Condition | Specified condition |
| X1-1 (SFR-) - X1-2 (SFR+) (*1) | Always | 1 MΩ or higher |
| Y1-1 (SFL-) - Y1-2 (SFL+) (*2) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 4.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the connectors to the front passenger side front seat side airbag assembly and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||