Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1830/57    Short in Driver Side Curtain Shield Squib Circuit

DTC    B1831/57    Open in Driver Side Curtain Shield Squib Circuit

DTC    B1832/57    Short to GND in Driver Side Curtain Shield Squib Circuit

DTC    B1833/57    Short to B+ in Driver Side Curtain Shield Squib Circuit

for Preparation Click here


DESCRIPTION

The driver side curtain shield squib circuit consists of the center airbag sensor assembly and the driver side curtain shield airbag assembly.
The circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side curtain shield squib circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1830/57
  1. Center airbag sensor assembly detects line short circuit signal in driver side curtain shield squib circuit 5 times during primary check.
  2. Driver side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Curtain shield airbag assembly LH (Driver side curtain shield squib) (LHD)
  3. Curtain shield airbag assembly RH (Driver side curtain shield squib) (RHD)
  4. Center airbag sensor assembly
B1831/57
  1. Center airbag sensor assembly detects open circuit signal in driver side curtain shield squib circuit for 2 seconds.
  2. Driver side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Curtain shield airbag assembly LH (Driver side curtain shield squib) (LHD)
  3. Curtain shield airbag assembly RH (Driver side curtain shield squib) (RHD)
  4. Center airbag sensor assembly
B1832/57
  1. Center airbag sensor assembly detects short circuit to ground signal in driver side curtain shield squib circuit for 0.5 seconds.
  2. Driver side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Curtain shield airbag assembly LH (Driver side curtain shield squib) (LHD)
  3. Curtain shield airbag assembly RH (Driver side curtain shield squib) (RHD)
  4. Center airbag sensor assembly
B1833/57
  1. Center airbag sensor assembly detects short circuit to B+ signal in driver side curtain shield squib circuit for 0.5 seconds.
  2. Driver side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Curtain shield airbag assembly LH (Driver side curtain shield squib) (LHD)
  3. Curtain shield airbag assembly RH (Driver side curtain shield squib) (RHD)
  4. Center airbag sensor assembly

WIRING DIAGRAM


H100113E03


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting CHECK MODE (signal check) with the intelligent tester (Click here).
  2. After selecting CHECK MODE (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).

1.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (DRIVER SIDE CURTAIN SHIELD SQUIB)
H100109E01
SST
09843-18060  
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the driver side curtain shield airbag assembly.

  1. Connect the white wire side of SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect a tester to the driver side curtain shield airbag assembly for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert the SST straight into the terminals of the connector.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1830, B1831, B1832, B1833 and 57 are not output.

    HINT:
    DTCs other than DTC B1830, B1831, B1832, B1833 and 57 may be output at this time, but they are not related to this check.



OK
REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY LH (LHD)

OK
REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH (RHD)
NG


2.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST from connector C.

  1. Check that the floor wire connectors (on the driver side curtain shield airbag assembly side) are not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE
OK


3.CHECK FLOOR WIRE (DRIVER SIDE CURTAIN SHIELD SQUIB CIRCUIT)
H100172E01
  1. Disconnect the connectors from the center airbag sensor assembly.

  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage.

      Standard Voltage:
      Tester connection
      Condition
      Specified condition
      J23-1 (ICL+) - Body ground (*1)
      Ignition switch ON
      Below 1 V
      J23-2 (ICL-) - Body ground (*1)
      Ignition switch ON
      Below 1 V
      J22-1 (ICR+) - Body ground (*2)
      Ignition switch ON
      Below 1 V
      J22-2 (ICR-) - Body ground (*2)
      Ignition switch ON
      Below 1 V

      *1: LHD
      *2: RHD

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance.

      Standard Resistance:
      Tester connection
      Condition
      Specified condition
      J23-1 (ICL+) - J23-2 (ICL-) (*1)
      Always
      Below 1 Ω
      J22-1 (ICR+) - J22-2 (ICR-) (*2)
      Always
      Below 1 Ω

      *1: LHD
      *2: RHD

  1. Check for short to ground in the circuit.

    1. Measure the resistance.

      Standard Resistance:
      Tester connection
      Condition
      Specified condition
      J23-1 (ICL+) - Body ground (*1)
      Always
      1 MΩ or higher
      J23-2 (ICL-) Body ground (*1)
      Always
      1 MΩ or higher
      J22-1 (ICR+) - Body ground (*2)
      Always
      1 MΩ or higher
      J22-2 (ICR-) Body ground (*2)
      Always
      1 MΩ or higher

      *1: LHD
      *2: RHD

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance.

      Standard Resistance:
      Tester connection
      Condition
      Specified condition
      J23-1 (ICL+) - J23-2 (ICL-) (*1)
      Always
      1 MΩ or higher
      J22-1 (ICR+) - J22-2 (ICR-) (*2)
      Always
      1 MΩ or higher

      *1: LHD
      *2: RHD



NG
REPAIR OR REPLACE FLOOR WIRE
OK


4.CHECK CENTER AIRBAG SENSOR ASSEMBLY
H100878E01
  1. Connect the connectors to the diver side curtain shield airbag assembly and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1830, B1831, B1832, B1833 and 57 are not output.

    HINT:
    DTCs other than DTC B1830, B1831, B1832, B1833 and 57 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK