DTC P0724 Brake Switch "B" Circuit High |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0724 | Stop light switch remains ON even when vehicle repeats 5 cycles of STOP (less than 3 km/h (1.86 mph)) and GO (30 km/h (18.65 mph) or more) (2 trip detection logic) |
|


| 1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.
Read the value displayed on the tester when the brake pedal is depressed and released.
| Brake Pedal | Display |
| Released | OFF |
| Depressed | ON |
|
| ||||
| OK | ||
| ||
| 2.CHECK STOP LIGHT SWITCH INSTALLATION |
Check the stop light switch installation (Click here).
| Result | Proceed To |
| OK (Hatchback) | A |
| OK (Sedan) | B |
| NG | C |
|
| ||||
|
| ||||
| A | |
| 3.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH) |
Disconnect the stop light control relay connector.
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.
Read the value displayed on the tester when the brake pedal is depressed and released.
| Brake Pedal | Display |
| Released | OFF |
| Depressed | ON |
Reconnect the stop light control relay connector.
|
| ||||
| OK | ||
| ||
| 4.INSPECT STOP LIGHT SWITCH ASSEMBLY |
![]() |
Remove the stop light switch assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Position | Specified Condition |
| 1 - 2 | Switch pin released | Below 1 Ω |
| Switch pin pushed in | 10 kΩ or higher | |
| 3 - 4 | Switch pin released | 10 kΩ or higher |
| Switch pin pushed in | Below 1 Ω |
Reinstall the stop light switch assembly.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM) |
![]() |
Disconnect the ECM connector.
Disconnect the stop light switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A21-36 (STP) - A13-1 | Always | Below 1 Ω |
| A21-35 (ST1-) - A13-4 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A21-36 (STP) or A13-1 - Body ground | Always | 10 kΩ or higher |
| A21-35 (ST1-) or A13-4 - Body ground | Always | 10 kΩ or higher |
| Result | Proceed To |
| OK (Hatchback) | A |
| OK (Sedan) | B |
| NG | C |
Reconnect the ECM connector.
Reconnect the stop light switch connector.
|
| ||||
|
| ||||
| A | |
| 6.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - STOP LIGHT SWITCH) |
![]() |
Disconnect the stop light control relay connector.
Disconnect the stop light switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J55-6 (+B) - A13-2 | Always | Below 1 Ω |
| J55-2 (STP) - A13-1 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| J55-6 (+B) or A13-2 - Body ground | Always | 10 kΩ or higher |
| J55-2 (STP) or A13-1 - Body ground | Always | 10 kΩ or higher |
Reconnect the stop light control relay connector.
Reconnect the stop light switch connector.
|
| ||||
| OK | ||
| ||