Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > TRC OFF Indicator Light does not Come ON

for Preparation Click here


DESCRIPTION

The skid control ECU is connected to the combination meter via CAN communication.
Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction and VSC controls. If TRC control is turned off, the TRC OFF indicator light will come on.

WIRING DIAGRAM

Refer to TRC OFF Indicator Light Remains ON .

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the brake actuator assembly, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A


2.READ VALUE USING INTELLIGENT TESTER (VSC OFF SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch to ON.

  1. Select the Data List on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    TRC/VSC Off Mode
    TRC/VSC off mode / Normal, TRC OFF or VSC OFF
    Normal: Normal mode
    TRC OFF: TRC OFF mode
    VSC OFF: VSC OFF mode
    -

  1. Using the intelligent tester, check the switch condition on the intelligent tester changes according to VSC OFF switch operation.

    OK:
    The intelligent tester display changes according to VSC OFF switch operation.



NG
Go to step 6
OK


3.REPLACE COMBINATION METER ASSEMBLY
  1. Turn the ignition switch off.

  1. Replace the combination meter.

    1. for Sedan (Click here).
    2. for Hatchback (Click here).


NEXT


4.CHECK THAT TRC OFF INDICATOR IS ILLUMINATED
  1. Check if the TRC OFF indicator is illuminated when the ignition switch is turned to ON.

    OK:
    TRC OFF indicator should be illuminated.

    HINT:
    When the ignition switch is turned to ON, TRC OFF indicator lights come on for approximately 3 seconds. This signal comes from the skid control ECU via CAN communication.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Sedan)
    B
    NG (for Hatchback)
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

END 

5.INSPECT VSC OFF SWITCH


    C154663E01
  1. Turn the engine switch off.

  1. Disconnect the VSC OFF switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (E) - 9 (+)
    Switch is pushed in
    Below 1 Ω
    6 (E) - 9 (+)
    Switch is not pushed in
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (VSC OFF Switch)

Result 
Result
Proceed to
OK
A
NG (for Sedan)
B
NG (for Hatchback)
C


B
REPLACE VSC OFF SWITCH (Click here)

C
REPLACE VSC OFF SWITCH (Click here)
A


6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
  1. Connect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A31-30 (CSW) - D106-9 (+)
    Always
    Below 1 Ω
    A31-30 (CSW) - Body ground
    Always
    10 kΩ or higher
    D106-6 (E) - Body ground
    Always
    Below 1 Ω

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION)