Home › ENGINE · 2NZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0134    Oxygen Sensor Circuit No Activity Detected (Bank 1 Sensor 1)

for Preparation Click here

HINT:
Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DESCRIPTION

Refer to DTC P0130 .

DTC No.
DTC Detection Conditions
Trouble Areas
P0134
Heated Oxygen (HO2) sensor (sensor 1) output does not indicate rich (more than 0.45 V) even once when conditions (a), (b), (c), (d) and (e) continue for more than 50 seconds (1 trip detection logic):
  1. (a) Engine speed: 1,400 rpm or more
  2. (b) Vehicle speed: 40 km/h (25 mph) or more
  3. (c) Throttle valve not fully closed
  4. (d) 180 seconds or more after starting engine
  5. (e) Engine coolant temperature more than 40°C (104°F)
  1. Open or short in HO2 sensor (sensor 1) circuit
  2. HO2 sensor heater (sensor 1)
  3. HO2 sensor (sensor 1)
  4. Fuel pressure
  5. Air induction system
  6. PCV hose connections
  7. PCV valve and hose
  8. Injector
  9. Exhaust gas leakage
  10. Integration relay (EFI relay)
  11. ECM

HINT:
If this DTC is set, check the output voltage of the HO2 sensor (sensor 1) by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / O2S B1S1.


WIRING DIAGRAM

Refer to DTC P0130 .

CONFIRMATION DRIVING PATTERN


C121872E09

HINT:
This confirmation driving pattern is used in the "PERFORM CONFIRMATION DRIVING PATTERN" procedure of the following diagnostic troubleshooting procedure.

  1. (1) Connect an intelligent tester to the DLC3.
  2. (2) Turn the ignition switch to ON and turn the tester on.
  3. (3) Clear DTCs (Click here).
  4. (4) Start the engine.
  5. (5) Allow the engine to idle until the engine coolant temperature reaches 40°C (104°F).
  6. (6) Drive the vehicle at a speed of more than 40 km/h (25 mph) for 3 minutes or more.

NOTICE:
If the conditions in this test are not strictly followed, malfunctions may not be detected.


INSPECTION PROCEDURE

HINT:
It is possible that the malfunctioning area can be found using the Active Test Control operation. The Active Test can determine if the heated oxygen sensor or other potential trouble areas are malfunctioning or not.
The injection volume can be switched to -12.5% (decrease) or +25% (increase) by the Active Test.
The Active Test procedure enables a technician to check and graph the voltage outputs of the heated oxygen sensors.

  1. Procedure:
    1. Connect an intelligent tester to the DLC3.
    2. Turn the ignition switch to ON.
    3. Warm up the engine by running the engine at 2,500 rpm for approximately 90 seconds.
    4. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
    5. Perform the Active Test while the engine is idling.

Standard:
The heated oxygen sensor reacts in accordance with the increases and decreases in injection volume:
+25% → RICH output: More than 0.5 V
-12.5% → LEAN output: Less than 0.4 V

NOTICE:
The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of 20 seconds.
If the vehicle is short of fuel, the air-fuel ratio becomes LEAN and the DTCs are recorded.


Case
Heated Oxygen Sensor (Sensor 1) Output Voltage
Heated Oxygen Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A150789E04
A150787E01
A150788E03
-
2
A150787E01
A150790E01
A150787E01
A150788E03
  1. Heated oxygen sensor (Sensor 1)
  2. Heated oxygen sensor heater (Sensor 1)
  3. Heated oxygen sensor circuit (Sensor 1)
3
A150787E01
A150789E04
A150787E01
A150790E01
  1. Heated oxygen sensor (Sensor 2)
  2. Heated oxygen sensor heater (Sensor 2)
  3. Heated oxygen sensor circuit (Sensor 2)
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Injector
  2. Fuel pressure
  3. Gas leak from exhaust system (Air-fuel ratio extremely RICH or LEAN)

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was LEAN or RICH, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0134)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0134
    A
    P0134 and other DTCs
    B

HINT:
If any DTCs other than P0134 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / O2S B1S1 and Engine Speed.

  1. Warm up the engine until the engine coolant temperature reaches more than 40°C (104°F).

  1. Rev the engine up to 4,000 rpm 3 times using the accelerator pedal.

  1. Read the output voltage of the front Heated Oxygen (HO2) sensor displayed on the tester when the engine speed is suddenly increased.

    Standard:
    HO2 sensor voltage output indicates 0.45 V or more (rich signal) at least once.



OK
Go to step 12
NG


3.CHECK PCV HOSE CONNECTIONS

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


4.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
A107936E07
  1. Disconnect the C36 HO2 sensor (sensor 1) connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    HT1A (1) - +B (2)
    5.3 to 7.5 Ω at 20 °C (68°F)
    HT1A (1) - E2 (4)
    10 kΩ or higher

  1. Reconnect the HO2 sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


5.INSPECT INTEGRATION NO.1 RELAY (EFI RELAY)
A107921E21
  1. Remove the integration relay from the engine room relay block.

  1. Inspect the EFI fuse.

    1. Remove the EFI fuse from the integration relay.

    2. Check the EFI fuse resistance.

      Standard resistance:
      Below 1 Ω

    3. Reinstall the EFI fuse.

  1. Inspect the EFI relay.

    1. Check the EFI relay resistance.

      Standard resistance:
      Tester Connections
      Specified Conditions
      1C-1 - 1A-4
      10 kΩ or higher
      Below 1 Ω
      (Apply battery voltage between terminals 1A-2 and 1A-3)

  1. Reinstall the integration relay.



NG
REPLACE INTEGRATION NO.1 RELAY
OK


6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
A105980E01

A112568E03

  1. Disconnect the C36 HO2 sensor (sensor 1) connector.

  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    OX1A (C36-3) - OX1A (C20-112)
    Below 1 Ω
    HT1A (C36-1) - HT1A (C20-109)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    OX1A (C36-3) or OX1A (C20-112) - Body ground
    10 kΩ or higher
    HT1A (C36-1) or HT1A (C20-109) - Body ground

  1. Reconnect the HO2 sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK WHETHER MISFIRE OCCURS BY MONITORING DTC AND DATA LIST


NG
TROUBLESHOOT MISFIRE
OK


8.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leaks.

    OK:
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


9.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


10.INSPECT FUEL INJECTOR
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor).



NG
REPLACE FUEL INJECTOR (Click here)
OK


11.CHECK FOR EXHAUST GAS LEAK

OK:
No gas leakage.



NG
REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT
OK

REPLACE HEATED OXYGEN SENSOR (Click here)  

12.PERFORM CONFIRMATION DRIVING PATTERN

HINT:
Clear all DTCs before performing the confirmation driving pattern.


NEXT


13.CHECK WHETHER DTC OUTPUT RECURS (DTC P0134)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    No output
    A
    P0134
    B



B
REPLACE ECM (Click here)
A


14.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
  1. If the vehicle has run out of fuel, proceed to A.

  1. If the vehicle has not run out of fuel, proceed to B.



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

DTC CAUSED BY RUNNING OUT OF FUEL