Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Stop Light Circuit

for Preparation Click here


DESCRIPTION

When the stop light switch is turned on, the current flows to the stop lights causing them to illuminate.

WIRING DIAGRAM


E174089E02


E131556E06


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT STOP LIGHT SWITCH


    A195013E02
  1. Remove the stop light switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Switch pin released
    Below 1 Ω
    Switch pin pushed in
    10 kΩ or higher
    3 - 4
    Switch pin released
    10 kΩ or higher
    Switch pin pushed in
    Below 1 Ω

  1. Reinstall the stop light switch.

Result 
Result
Proceed to
OK
A
NG (for Hatchback)
B
NG (for Sedan)
C


B
REPLACE STOP LIGHT SWITCH (Click here)

C
REPLACE STOP LIGHT SWITCH (Click here)
A


2.CHECK HARNESS AND CONNECTOR (STOP FUSE - STOP LIGHT SWITCH)
A195017E02
  1. Disconnect the A13 stop light switch connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A13-2 - Body ground
    Ignition switch ON
    11 to 14 V

    Result 
    Result
    Proceed to
    OK (for Sedan)
    A
    OK (for Hatchback)
    B
    NG
    C



B
Go to step 5

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


3.INSPECT BULB (REAR STOP LIGHT BULB)
E174090E02
  1. Remove the rear combination light assembly.

  1. Remove the high mounted stop light assembly.

  1. Apply battery voltage to the terminals and check that the rear stop light and high mounted stop light illuminate.

    OK:
    Rear Stop Light:
    Measurement Condition
    Specified Condition
    Positive battery - Terminal 1
    Negative battery - Terminal 6
    Rear stop light illuminates
    High Mounted Stop Light (w/ Rear Spoiler):
    Measurement Condition
    Specified Condition
    Positive battery - Terminal 2
    Negative battery - Terminal 1
    High mounted stop light illuminates
    High Mounted Stop Light (w/o Rear Spoiler):
    Measurement Condition
    Specified Condition
    Positive battery - Terminal 1
    Negative battery - Terminal 2
    High mounted stop light illuminates

  1. Reinstall the rear combination light assembly.

  1. Reinstall the high mounted stop light assembly.
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Sedan with Stop Light Bulb)
    B
    NG (for Sedan with High Mounted Stop Light (w/ Rear Spoiler))
    C
    NG (for Sedan with High Mounted Stop Light (w/o Rear Spoiler))
    D



B
REPLACE STOP LIGHT BULB (Click here)

C
REPLACE HIGH MOUNTED STOP LIGHT (Click here)

D
REPLACE HIGH MOUNTED STOP LIGHT (Click here)
A


4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - REAR STOP LIGHT)
E174117E01
  1. Disconnect the A13 stop light switch connector.

  1. Disconnect the J41 and J42 rear combination light assembly connectors.

  1. Disconnect the J47 or J48 high mounted stop light assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A13-1 - J41-1
    Always
    Below 1 Ω
    A13-1 or J41-1 - Body ground
    Always
    10 kΩ or higher
    A13-1 - J42-1
    Always
    Below 1 Ω
    A13-1 or J42-1 - Body ground
    Always
    10 kΩ or higher
    A13-1 - J48-2*1
    Always
    Below 1 Ω
    A13-1 or J48-2*1 - Body ground
    Always
    10 kΩ or higher
    A13-1 - J47-1*2
    Always
    Below 1 Ω
    A13-1 or J47-1*2 - Body ground
    Always
    10 kΩ or higher

    1. *1: w/ Rear spoiler
    2. *2: w/o Rear spoiler

  1. Reconnect the stop light switch connector.

  1. Reconnect the rear combination light assembly connectors.

  1. Reconnect the high mounted stop light assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR STOP LIGHT - BODY GROUND) 

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - STOP FUSE AND BODY GROUND)


    E142629E23
  1. Disconnect the J55 stop light control relay connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    J55-2 (STP) - Body ground
    Brake pedal released
    Below 1 V
    Brake pedal depressed
    11 to 14 V
    J55-6 (+B) - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J55-4 (GND) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the stop light control relay connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT STOP LIGHT CONTROL RELAY


    E150985E15
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    J55-8 (OUT) - Body ground
    Brake pedal released
    Below 1 V
    Brake pedal depressed
    11 to 14 V



NG
REPLACE STOP LIGHT CONTROL RELAY
OK


7.INSPECT BULB (REAR STOP LIGHT BULB)
B129902E03
  1. Remove the rear combination light assembly.

  1. Remove the high mounted stop light assembly.

  1. Apply battery voltage to the terminals and check that the rear stop light and high mounted stop light illuminate.

    OK:
    High Mounted Stop Light:
    Measurement Condition
    Specified Condition
    Positive battery - Terminal 1
    Negative battery - Terminal 2
    High mounted stop light illuminates
    Rear Stop Light:
    Measurement Condition
    Specified Condition
    Positive battery - Terminal 5
    Negative battery - Terminal 6
    Rear stop light illuminates

  1. Reinstall the rear combination light assembly.

  1. Reinstall the high mounted stop light assembly.
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Hatchback with Stop Light Bulb)
    B
    NG (for Hatchback with High Mounted Stop Light)
    C



B
REPLACE STOP LIGHT BULB (Click here)

C
REPLACE HIGH MOUNTED STOP LIGHT (Click here)
A


8.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - REAR STOP LIGHT)
E174092E04
  1. Disconnect the J55 stop light control relay connector.

  1. Disconnect the J3 and J4 rear combination light assembly connectors.

  1. Disconnect the M1 high mounted stop light assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J55-8 (OUT) - J3-5
    Always
    Below 1 Ω
    J55-8 (OUT) or J3-5 - Body ground
    Always
    10 kΩ or higher
    J55-8 (OUT) - J4-5
    Always
    Below 1 Ω
    J55-8 (OUT) or J4-5 - Body ground
    Always
    10 kΩ or higher
    J55-8 (OUT) - M1-1
    Always
    Below 1 Ω
    J55-8 (OUT) or M1-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the stop light control relay connector.

  1. Reconnect the rear combination light assembly connectors.

  1. Reconnect the high mounted stop light assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR STOP LIGHT - BODY GROUND)