Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Brake Actuator (Skid Control ECU) Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
Brake Actuator (Skid Control ECU) Communication Stop Mode
  1. "ABS/VSC/TRC" not displayed on "Communication Bus Check" screen of intelligent tester
  2. Applies to "Brake Actuator (Skid Control ECU) Communication Stop Mode" in "DTC combination table"
  1. Power source circuit of brake actuator (skid control ECU)
  2. Brake actuator (skid control ECU) branch wire or connector
  3. Brake actuator (skid control ECU)

HINT:
For vehicle with ABS only.


WIRING DIAGRAM


C120497E38


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.CHECK CAN BUS LINE FOR DISCONNECTION (BRAKE ACTUATOR (SKID CONTROL ECU) BRANCH WIRE)


    C168930E15
  1. for Hatchback:

    1. Turn the ignition switch off.

    2. Disconnect the A15 brake actuator (skid control ECU) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      A15-25 (CANH) - A15-14 (CANL)
      Ignition switch off
      54 to 69 Ω



    C118165E34
  1. for Sedan:

    1. Turn the ignition switch off.

    2. Disconnect the A15 brake actuator (skid control ECU) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      A15-6 (CANH) - A15-5 (CANL)
      Ignition switch off
      54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BRAKE ACTUATOR (SKID CONTROL ECU) (CAN-H, CAN-L)
OK


2.CHECK HARNESS AND CONNECTOR (IG1, GND1)


    C168930E18
  1. for Hatchback:

    1. Disconnect the A15 brake actuator (skid control ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A15-1 (GND) - Body ground
      Always
      Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A15-34 (IG1) - Body ground
      Ignition switch ON
      11 to 14 V



    C118165E35
  1. for Sedan:

    1. Disconnect the A15 brake actuator (skid control ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A15-2 (GND1) - Body ground
      Always
      Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A15-25 (IG1) - Body ground
      Ignition switch ON
      11 to 14 V

Result 
Result
Proceed to
NG
A
OK (for Sedan)
B
OK (for Hatchback)
C


B
REPLACE BRAKE ACTUATOR (SKID CONTROL ECU) (Click here)

C
REPLACE BRAKE ACTUATOR (SKID CONTROL ECU) (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR