Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode
  1. "ABS/VSC/TRC" not displayed on "Communication Bus Check" screen of intelligent tester
  2. Applies to "ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode" in "DTC combination table"
  1. Power source circuit of ABS and traction actuator (skid control ECU)
  2. ABS and traction actuator (skid control ECU) branch wire or connector
  3. ABS and traction actuator (skid control ECU)

HINT:
For vehicle with VSC only.


WIRING DIAGRAM


E191954E02


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
  4. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.CHECK CAN BUS LINE FOR CONNECTION (ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) BRANCH WIRE)


    E191940E18
  1. Turn the ignition switch off.

  1. Disconnect the A31 ABS and traction actuator (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A31-25 (CANH) - A31-14 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ABS and Traction Actuator (Skid Control ECU))



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) (CAN-H, CAN-L)
OK


2.CHECK HARNESS AND CONNECTOR (IG1, GND1, GND2)


    E191940E19
  1. Disconnect the A31 ABS and traction actuator (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A31-13 (GND2) - Body ground
    Always
    Below 1 Ω
    A31-1 (GND1) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ABS and Traction Actuator (Skid Control ECU))

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A31-34 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Result 
    Result
    Proceed to
    OK
    (for Hatchback)
    A
    OK
    (for Sedan)
    B
    NG
    C



B
REPLACE ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) (Click here)