Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > CAN Main Wire for Disconnection (LHD Models)

for Preparation Click here


DESCRIPTION

There may be an open circuit in the main wire and/or the DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or higher.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 69 Ω or higher.
  1. CAN main wire or connector
  2. D-CAN junction connector
  3. P-CAN junction connector
  4. ECM
  5. Power steering ECU

WIRING DIAGRAM


E173564E03


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.CHECK DLC3


    C140672E07
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D15-6 (CANH) - D15-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    NOTICE:
    When the measured value is 132 Ω or higher and a CAN communication system diagnostic trouble code is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "How to Proceed with Troubleshooting" (Click here) after repairing the trouble area.



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK


2.CHECK CAN MAIN WIRE OR CONNECTOR (D-CAN J/C SIDE)


    E160790E01
  1. Turn the ignition switch off.

  1. Disconnect the D42 P-CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-11 (TOLH) - D42-22 (TOLH)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 7
OK


3.CONNECT CONNECTOR
  1. Reconnect the P-CAN junction connector.


NEXT


4.CHECK CAN MAIN WIRE OR CONNECTOR (POWER STEERING ECU)


    G100242E32
  1. Turn the ignition switch off.

  1. Disconnect the D31 power steering ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D31-1 (CANH) - D31-7 (CANL)
    Ignition switch off
    108 to 132 Ω

Result 
Result
Proceed to
NG
A
OK (for Hatchback)
B
OK (for Sedan)
C


B
REPLACE POWER STEERING ECU (Click here)

C
REPLACE POWER STEERING ECU (Click here)
A


5.CONNECT CONNECTOR
  1. Reconnect the power steering ECU connector.


NEXT


6.CHECK CAN MAIN WIRE CONNECTED TO POWER STEERING ECU (P-CAN J/C - POWER STEERING ECU)


    E160790E04
  1. Turn the ignition switch off.

  1. Disconnect the D42 P-CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-4 (EPS) - D42-15 (EPS)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER STEERING ECU (CAN-H, CAN-L)
OK

REPLACE P-CAN JUNCTION CONNECTOR 

7.CONNECT CONNECTOR
  1. Reconnect the P-CAN junction connector.


NEXT


8.CHECK CAN MAIN WIRE OR CONNECTOR (ECM)


    C125895E19
  1. Turn the ignition switch off.

  1. Disconnect the A21 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A21-41 (CANH) - A21-49 (CANL)
    Ignition switch off
    108 to 132 Ω

Result 
Result
Proceed to
NG
A
OK (for 1NZ-FE)
B
OK (for 2NZ-FE)
C


B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A


9.CONNECT CONNECTOR
  1. Reconnect the ECM connector.


NEXT


10.CHECK CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - ECM)


    E160790E02
  1. Turn the ignition switch off.

  1. Disconnect the D41 D-CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance::
    Tester Connection
    Switch Condition
    Specified Condition
    D41-4 (EFI) - D41-15 (EFI)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - D-CAN J/C (CAN-H, CAN-L))
OK


11.CHECK CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - P-CAN J/C)


    E160790E03
  1. Turn the ignition switch off.

  1. Disconnect the D41 D-CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance::
    Tester Connection
    Switch Condition
    Specified Condition
    D41-11 (TORH) - D41-22 (TORH)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - P-CAN J/C)
OK

REPLACE D-CAN JUNCTION CONNECTOR