CAN COMMUNICATION SYSTEM > CAN Main Wire for Disconnection (RHD Models) |
| Symptom | Trouble Area |
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 69 Ω or higher. |
|

| 1.CHECK DLC3 |
![]() |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D15-6 (CANH) - D15-14 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | |
| 2.CHECK CAN MAIN WIRE OR CONNECTOR (D-CAN J/C SIDE) |
![]() |
Turn the ignition switch off.
Disconnect the D41 P-CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D41-11 (TORH) - D41-22 (TORH) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | |
| 3.CONNECT CONNECTOR |
Reconnect the P-CAN junction connector.
| NEXT | |
| 4.CHECK CAN MAIN WIRE OR CONNECTOR (ECM) |
![]() |
Turn the ignition switch off.
Disconnect the A21 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A21-41 (CANH) - A21-49 (CANL) | Ignition switch off | 108 to 132 Ω |
| Result | Proceed to |
| NG | A |
| OK (for 1NZ-FE) | B |
| OK (for 2NZ-FE) | C |
|
| ||||
|
| ||||
| A | |
| 5.CONNECT CONNECTOR |
Reconnect the ECM connector.
| NEXT | |
| 6.CHECK CAN MAIN WIRE OR CONNECTOR (P-CAN J/C - ECM) |
![]() |
Turn the ignition switch off.
Disconnect the D41 P-CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D41-4 (EFI) - D41-15 (EFI) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 7.CONNECT CONNECTOR |
Reconnect the P-CAN junction connector.
| NEXT | |
| 8.CHECK CAN MAIN WIRE OR CONNECTOR (POWER STEERING ECU) |
![]() |
Turn the ignition switch off.
Disconnect the D31 power steering ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D31-1 (CANH) - D31-7 (CANL) | Ignition switch off | 108 to 132 Ω |
| Result | Proceed to |
| NG | A |
| OK (for Hatchback) | B |
| OK (for Sedan) | C |
|
| ||||
|
| ||||
| A | |
| 9.CONNECT CONNECTOR |
Reconnect the power steering ECU connector.
| NEXT | |
| 10.CHECK CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - POWER STEERING ECU) |
![]() |
Turn the ignition switch off.
Disconnect the D42 D-CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D42-4 (EPS) - D42-15 (EPS) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | |
| 11.CHECK CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - P-CAN J/C) |
![]() |
Turn the ignition switch off.
Disconnect the D42 D-CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D42-11 (TOLH) - D42-22 (TOLH) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||